Refine Your Search

Search Results

Standard

General Specification for Elastomeric Bearings

2017-05-23
WIP
AS85598
This document defines the requirements for spherical, radial-journal, conical and thrust bearings which are of laminated elastomeric construction. These bearings are for use in an environment having a temperature spectrum within a maximum ambient temperature range of -65 degrees F to +160 degrees F while reacting oscillating loads and motions.
Standard

Bearings, Plain, Self-Aligning, All Metal General Specification for

2012-02-08
CURRENT
AS8976A
This specification covers all metal plain spherical bearings which are self-aligning for use between 65 °F to 250 °F. This specification covers bearings with alloy steel races, aluminum bronze races, and an entierly CRES bearing (ball and race). All units are inches, unless otherwise stated.
Standard

Rod End Locking Device Selection Criteria

2020-07-01
CURRENT
ARP6910
This ARP discusses common rod end locking devices with recommended applications and some of the advantages and disadvantages of specific configurations. An appendix is included with factors to be considered for selection of positive locking devices and a discussion of safetying devices for rod end assemblies.
Standard

Plain Bearing Wear Measurement

2016-12-12
CURRENT
ARP5448/7A
This standard details two methods of inspecting PTFE lined spherical or journal bearing wear outside the test apparatus. The methods described herein are applicable only to bearings which were unidirectionally loaded and the area of sliding wear is known and held constant throughout the dynamic test. The two methods described are: a Destructive Inspection - Cut and measure (not applicable to molded liners) b Nondestructive Inspection - Radial play (gauge) measurement
Standard

Plain Spherical Bearing Radial and Axial Clearance Measurement

2007-02-27
CURRENT
ARP5448/8A
This test method provides a guidance for determining the total free play between the ball and outer ring of a spherical bearing when measured in both the radial and axial directions. Bearings covered by this test method include all plain spherical type bearings, both self-lubricated (lined) and metal-to-metal.
Standard

Plain Bearing Wear Measurement

2002-07-31
HISTORICAL
ARP5448/7
This standard details two methods of inspecting TFE lined spherical or journal bearing wear outside the test apparatus. The methods described herein are applicable only to bearings which were unidirectionally loaded and the area of sliding wear is known and held constant throughout the dynamic test. The two methods described are: a Destructive Inspection - Cut and measure (not applicable to molded liners) b Non-destructive Inspection - Radial play (gage) measurement
Standard

Plain Spherical Bearing Radial and Axial Clearance Measurement

2001-04-01
HISTORICAL
ARP5448/8
This test method provides a guidance for determining the total free play between the ball and outer ring of a spherical bearing when measured in both the radial and axial directions. Bearings covered by this test method include all plain spherical type bearings, both self-lubricated (lined) and metal-to-metal.
Standard

Plain Spherical Bearing Conformity Examination

2002-05-21
HISTORICAL
ARP5448/6
This method outlines a standard procedure for performing conformity tests of bearings utilizing liners of bonded polytetrafluoroethylene (PTFE). The data from these tests shall be used to determine if the product meets the conformity requirements of the applicable specification.
Standard

Plain Bearing Low Speed Oscillation Test

2002-07-31
HISTORICAL
ARP5448/3
This test method outlines a standard procedure for performing unidirectional load dynamic testing of self-lubricating bearings at room temperature, elevated temperature or sub-zero temperature, dry or contaminated with fluids. The wear data from these tests is to be used for qualification and to establish bearing design criteria.
Standard

Plain Bearing Low Speed Oscillation Test

2016-07-19
CURRENT
ARP5448/3A
This test method outlines a recommended procedure for performing unidirectional load dynamic testing of self-lubricating bearings at room temperature, elevated temperature or sub-zero temperature, dry or contaminated with fluids. The wear data from these tests is to be used for qualification and to establish bearing design criteria.
Standard

Plain Spherical Bearing Conformity Examination

2017-02-21
CURRENT
ARP5448/6A
This method outlines a standard procedure for performing conformity tests of bearings utilizing liners of bonded polytetrafluoroethylene (PTFE). The data from these tests shall be used to determine if the product meets the conformity requirements of the applicable specification.
X