Refine Your Search

Topic

Author

Search Results

Standard

Cartridge Cavity

2018-10-30
CURRENT
J2494/4_201810
This SAE Standard covers complete general and dimensional data for the manufacture of, T6061-T6 Aluminum cavities designed to receive Push To Connect threadless fittings known as “cartridges“, for air brake applications. This document is not intended to specify or recommend any style or manufacture of such cartridges but to establish uniform cavity dimensions for interchangeability purposes.
Standard

Standard Rainflow File Format

2002-04-30
HISTORICAL
J2623_200204
This SAE Standard provides a definition of a rainflow file format. This type of simple text file would contain all relevant information about the rainflow cycle content of a time history. Included information are Comments, Signal Range, Signal Mean, Number of Cycles, Signal Maximum, Signal Minimum. Rainflow cycle counting has become the most accepted procedure for identifying material fatigue relevant cycles in complex variable amplitude load time histories. The cycle counting methods account for the effects of material plasticity and material memory of prior deformation, and the resulting compressed history information is used by durability analysts to estimate the effects of a given service or test history.
Standard

Standard Rainflow File Format

2018-08-24
CURRENT
J2623_201808
This SAE Standard provides a definition of a rainflow file format. This type of simple text file would contain all relevant information about the rainflow cycle content of a time history. Included information are Comments, Signal Range, Signal Mean, Number of Cycles, Signal Maximum, Signal Minimum. Rainflow cycle counting has become the most accepted procedure for identifying material fatigue relevant cycles in complex variable amplitude load time histories. The cycle counting methods account for the effects of material plasticity and material memory of prior deformation, and the resulting compressed history information is used by durability analysts to estimate the effects of a given service or test history.
Standard

Crane Boom Hoist Disengaging Device

2011-08-04
CURRENT
J999_201108
This SAE Standard applies to cranes which are equipped to adjust the boom angle by hoisting and lowering means through rope reeving.
Standard

Discharge Forward Lighting System and Subsystems

2005-10-03
HISTORICAL
J2009_200510
This SAE Recommended Practice applies to motor vehicle forward illumination systems and subsystems generated by discharge sources. It provides test methods, requirements, and guidelines applicable to the special characteristics of gaseous discharge lighting devices which supplement those required for forward illumination systems using incandescent light sources. The document is applicable to both discharge forward lighting systems, subsystems and components. This document is intended to be a guide to standard practice and is subject to change to reflect additional experience and technical advances.
Standard

Fuel Tank Filler Cap and Cap Retainer

2012-06-29
CURRENT
J829_201206
This SAE Standard was developed primarily for passenger car and truck applications for the sizes indicated, but it may be used in marine, industrial, and similar applications.
Standard

Brake-Stroke Indicator Design Guideline for Cam or Disc Air-Brake Actuators

2012-06-19
HISTORICAL
J1953_201206
This SAE Recommended Practice shall cover mechanical- readjust stroke indicators for actuators with visible exposed pushrods and electrical-readjust stroke indicators for all air-brake actuators. This device shall indicate the foundation brake(s) may require adjustment or service when inspected per vehicle manufacturer's procedures. A measurement shall be made to determine actual stroke measurement for any system not factory calibrated. Stroke indication accuracy of an air-brake actuator can be assured only when all of its components are supplied by the original brake actuator manufacturer.
Standard

Guidelines for Liquid Level Indicators

2007-04-30
HISTORICAL
J48_200704
This SAE Recommended Practice pertains to liquid level determination for any compartment of off-road machinery as defined in SAE J1116 and J1057.
Standard

Holes in Bolt and Screw Shanks and Slots in Nuts for Cotter Pins

2013-04-16
HISTORICAL
J485_201304
SAE J485 specifies the recommended nominal diameters and locations of holes in bolt or screw shanks, and nominal widths and depths of slots in nuts, for use with the recommended sizes of inch-series cotter pins, as shown in Table 1.
Standard

Countersunk Square Holes for Cutting Edges and End Bits

2011-10-25
CURRENT
J740_201110
To be used on cutting edges and end bits in conjunction with No. 3 head plow bolts (Ref. ANSI B18.9) typically used on off-road self-propelled work machines as described in SAE J1116. Cutting edges are further defined in SAE J737, J739 and J1304. End bits are further defined in SAE J63. 1 When section thickness exceeds A in drawing 1 (Figure 2) (countersunk one side) or B in drawing 4 (countersunk both sides), use counterbore with diameter D, as shown in cross section drawings 2, 5 and 6, or extended countersink C, as shown in cross section drawings 3 and 7. 2 The inscribed circle of the square holes shall be concentric with countersink or counterbore within 0.03 in (0.8 mm).
Standard

Maintenance Interval Chart

2018-09-25
WIP
J753
Instructions on this chart are intended to be used as a ready reference by personnel responsible for servicing off-road self-propelled work machines described in SAE J1116, categories 1, 2, 3, and 4. Detailed maintenance and service guidelines are reserved for maintenance, operator, and lubrication manuals as defined in SAE J920.
Standard

Maintenance Interval Chart

2011-10-27
CURRENT
J753_201110
Instructions on this chart are intended to be used as a ready reference by personnel responsible for servicing off-road self-propelled work machines described in SAE J1116, categories 1, 2, 3, and 4. Detailed maintenance and service guidelines are reserved for maintenance, operator, and lubrication manuals as defined in SAE J920.
Standard

Loading Ability Test Procedure - Scrapers

2011-10-27
CURRENT
J764_201110
This SAE Information Report applies to all independent or combination construction and industrial machines that are designed to scraper-load and transport material. (See SAE J1116 and J1057a.)
Standard

Effective Dates of New or Revised Technical Reports

1985-06-01
J301_198506
The final approval date for Fuels and Lubricants technical reports is shown following the J-report number. This approval date is the date of final approval by the Fuels and Lubricants Council. It is effective immediately subsequent to Council approval for newly issued Standards, Recommended Practices, and Information Reports, and also for revised Information Reports. In the case of revised or cancelled Standards or Recommended Practices (used to define product quality), an 18 month grace period is advised before they become fully effective.
Standard

Effective Dates of New or Revised Technical Reports

1987-06-01
J301_198706
The final approval date for Fuels and Lubricants technical reports is shown following the J-report number. This approval date is the date of final approval by the Fuels and Lubricants Council. It is effective immediately subsequent to Council approval for newly issued Standards, Recommended Practices, and Information Reports, and also for revised Information Reports. In the case of revised or cancelled Standards or Recommended Practices (used to define product quality), an 18 month grace period is advised before they become fully effective.
Standard

Survey of Known Protocols

1993-04-01
HISTORICAL
J2056/2_199304
This SAE Information Report is a summary comparison of existing protocols found in manufacturing, automotive, aviation, military, and computer applications which provide background or may be applicable for Class C application. The intent of this report is to present a summary of each protocol, not an evaluation. This is not intended to be a comprehensive review of all applicable protocols. The form for evaluation of a protocol exists in this paper and new protocols can be submitted on this form to the committee for consideration in future revisions of this report. This report contains a table which provides a side-by-side comparison of each protocol considered. The subsequent section provides a more detailed examination of the protocol attributes. Many of the protocols do not specify a method for one or more of the criteria. In these circumstances 'under defined' or 'not specified' will appear under the heading.
Standard

Elastomeric Bushing "TRAC" Application Code

2017-02-09
CURRENT
J1883_201702
The bushing "TRAC" code is intended to be a tool that will aid in the definition of the geometric environment for the test, or use, of an elastomeric bushing.
X