Search Results

The target of the work is to find out the algorithm of definition of the ratios of mechanical part of complex powersplit CVT/IVT system with regard to the highest achievable efficiency. The presented synthesis is focused on powersplit systems, which will consist of a CVT part, differential and eventually by-pass gear. The algorithm will be programmed and become an integral part of the program Sungear developed on Czech Technical University in Prague for analyses and synthesis of planetary stepped transmissions and CVT/IVT powersplit systems. The article will mainly present the algorithm of definition of efficient powersplit system. For the search of the efficient powersplit system we assume that the following parameters are given: a Spread and efficiency of used CVT system. b Total spread of the whole powersplit CVT/IVT mechanism. c Optional: Ratios of the used CVT system. d Optional: Ratios of the whole powersplit CVT/IVT system.

The presented paper deals with a methodology to model cycle-to-cycle variations (CCV) in 0-D/1-D simulation tools. This is achieved by introducing perturbations of combustion model parameters. To enable that, crank angle resolved data of individual cycles (pressure traces) have to be available for a reasonable number of engine cycles. Either experimental data or 3-D CFD results can be applied. In the presented work, experimental data of a single-cylinder research engine were considered while predicted LES 3-D CFD results will be tested in the future. Different engine operating points were selected - both stable ones (low CCV) and unstable ones (high CCV). The proposed methodology consists of two major steps. First, individual cycle data have to be matched with the 0-D/1-D model, i.e., combustion model parameters are varied to achieve the best possible match of pressure traces - an automated optimization approach is applied to achieve that.

The physical 1-D model of a radial turbine consists in a set of gas ducts featuring total pressure and/or temperature changes and losses. This model has been developed using the basic modules of generalized 1-D manifold solver. The tools for it were presented at SAE 2008 and 2009 World Congresses. The model published before is amended by a semi-empiric mechanical loss and windage loss modules. The instantaneous power of a turbine is integrated along the rotating impeller channel using Euler turbine theorem, which respects the local unsteadiness of mass flow rate along the channel. The main aim of the current contribution is to demonstrate the use of measured turbine maps for calibration of unsteady turbine model for different lay-outs of turbine blade cascades. It is important for VG turbines for the optimal matching to different engine speeds and loads requirements.

This article presents results of the Design Assistance System (DASY) development and examples of its application for engine concept modeling. The software (DASY) for creating and maintaining knowledge database was developed. This software is targeted to simplify and speed up the concept design process. The targets were met by providing the high level of flexibility along with a simple user interface. Two examples that show interaction of DASY with computer-aided design (CAD) software are presented. The DASY creates a template for conserving the knowledge acquired during engine design in the past. It provides hints for the future design tasks by offering a data of similar engines, based on experiments and simulations at different levels of complexity and profoundness.

In spark-ignition engines, fluctuations of the in-cylinder pressure trace and the apparent rate of heat release are usually observed from one cycle to another. These Cycle-to-Cycle Variations (CCV) are affected by the early flame development and the subsequent flame front propagation. The CCV are responsible for engine performance (e.g. fuel consumption) and the knock behavior. The occurrence of the phenomena is unpredictable and the stochastic nature offers challenges in the optimization of engine control strategies. In the present work, CCV are analyzed in terms of their impact on the engine knock behavior and the related efficiency. Target is to estimate the possible fuel consumption savings in steady-state operation and in the drivecycle, when CCV are reduced. Since CCV are immanent on real engines, such a study can only be done by means of simulation.

The current state-of-the-art offers two extremes of engine mechanical loss models: pure empirical models, using, e.g., regression models based on experimental results, and full-sized 3-D hydrodynamic friction models, solving Reynolds-like lubrication equations for complicated geometry of piston ring/cylinder liner or load-distorted shapes of crankshaft/connecting rod bearings and journals. Obviously, the former method cannot be reliably extrapolated while the latter is too complicated, especially for the early stage of design. The aim of the current paper is describing the development and experimental calibration of the physical cranktrain model for FMEP prediction, based on simplified phenomenological model of mixed friction. The model uses simply defined shapes of Stribeck curves (friction coefficient) in dependence on Sommerfeld number, i.e., on effective sliding velocity, oil viscosity, dimension scaling factor and the normal force load.

The paper describes a way to a 1-D central streamline model of a radial turbine flow, suitable for twin-scroll description and based on approximation of real physics of flow mixing and energy transformation. The original 1-D model of a single scroll turbine, described earlier in numerous SAE papers, has been amended by twin-scroll nozzles (both vaneless or with blade cascades) and mixing of individual partitions of flows upstream of additional vaneless nozzle and an impeller. This model is transferable to 1-D unsteady simulations as it is (i.e., using quasi-steady approach) or using 1-D unsteady solvers. It has suitable features even for more detailed description of turbine flows and energy transformation. The first results of pulse influence on turbine maps delivered expected results consisting of complicated interaction between individual losses.

The objective of this paper is to present the results of the GT Power calibration with engine test results of the air loop system technology down selection described in the SAE Paper No. 2012-01-0831. Two specific boosting systems were identified as the preferred path forward: (1) Super-turbo with two speed Roots type supercharger, (2) Super-turbo with centrifugal mechanical compressor and CVT transmission both downstream a Fixed Geometry Turbine. The initial performance validation of the boosting hardware in the gas stand and the calibration of the GT Power model developed is described. The calibration leverages data coming from the tests on a 2 cylinder 2-stroke 0.73L diesel engine. The initial flow bench results suggested the need for a revision of the turbo matching due to the big gap in performance between predicted maps and real data. This activity was performed using Honeywell turbocharger solutions spacing from fixed geometry waste gate to variable nozzle turbo (VNT).