Search Results

The drive to reduce particle emissions from heavy-duty diesel engines has reached the stage where the contribution from the lubricant can have a major impact on the total amount of particulate matter (PM). This paper proposes a model to predict the survival rate (unburnt oil divided by oil consumption) of the hydrocarbons from the lubricant consumed in the cylinder. The input data are oil consumption and cylinder temperature versus crank angle. The proposed model was tuned to correlate well with data from a six-cylinder heavy-duty diesel engine that meets the Euro 5 legislation without exhaust gas aftertreatment. The measured (and modelled) oil survival shows a strong correlation with engine power. The maximum oil survival rate measured (19%) was at motoring conditions at high speed. For this engine, loads above 100 kW yielded an oil survival rate of nearly zero.

EGR has been proven to reduce NOx emissions from diesel engines significantly and is nowadays widely used in production engines. To reach future emission legislation standards, alternative EGR-routings that deliver higher EGR-rates get into the focus of researchers. As the steady-state emissions are reduced more and more, the emission peaks in transient parts of driving cycles gain importance. Therefore it is interesting to analyze the transient behavior of different EGR-routings. In this work, a 1-D simulation is performed in GT-Power for a 1.9 liter passenger car diesel engine equipped with cooled short-route EGR and a variable geometry turbine. For calibration of the simulation, load transients are measured including the measurement of transient EGR-rates using a fast CO2-analyzer and cylinder pressure to obtain heat-release data.

In order for premixed methane diesel dual fuel engines to meet current and future legislation, the emissions of unburned hydrocarbons must be reduced while high efficiency and high methane utilization is maintained. This paper presents an experimental investigation into the effects of in cylinder air motion, swirl and tumble, on the emissions, heat transfer and combustion characteristics of dual fuel combustion at different air excess ratios. Measurements have been carried out on a single cylinder engine equipped with a fully variable valve train, Lotus AVT. By applying different valve lift profiles for the intake valves, the swirl was varied between 0.5 and 6.5 at BDC and the tumble between 0.5 and 4 at BDC. A commercial 1D engine simulation tool was used to calculate swirl number and tumble for the different valve profiles. Input data for the simulation software was generated using a steady-state flow rig with honeycomb torque measurements.

In the last couple of decades, countries have enacted new laws concerning environmental pollution caused by heavy-duty commercial and passenger vehicles. This is done mainly in an effort to reduce smog and health impacts caused by the different pollutions. One of the legislated pollutions, among a wide range of regulated pollutions, is nitrogen oxides (commonly abbreviated as NOx). The SCR (Selective Catalytic Reduction) was introduced in the automotive industry to reduce NOx emissions leaving the vehicle. The basic idea is to inject a urea solution (AdBlue™) in the exhaust gas before the gas enters the catalyst. The optimal working temperature for the catalyst is somewhere in the range of 300 to 400 °C. For the reactions to occur without a catalyst, the gas temperature has to be at least 800 °C. These temperatures only occur in the engine cylinder itself, during and after the combustion.

An afterburner-assisted turbocharged single-cylinder 425 cc two-stroke SI-engine is described in this simulation study. This engine is intended as a Backup Range Extender (REX) application for heavy-duty battery electric vehicles (BEV) when external electric charging is unavailable. The 425 cc engine is an upscaled version of a 125 cc port-injected engine [26] which demonstrated that the selected technology could provide a specific power level of 400 kW/L and the desired 150 kW in a heavy duty BEV application. The 425 cc single cylinder two-stroke engine is an existing engine as one half of a 850 cc snowmobile engine. This simulation study includes upscaling of the swept volume, impact on engine speed and gas exchange properties. In the same way as for the 125cc engine [26], the exhaust gases reaches the turbine through a tuned exhaust pipe and an afterburner or oxidation catalyst.

Diesel engine manufacturers strive towards further efficiency improvements. Thus, reducing in-cylinder heat losses is becoming increasingly important. Understanding how location, thermal insulation, and engine operating conditions affect the heat transfer to the combustion chamber walls is fundamental for the future reduction of in-cylinder heat losses. This study investigates the effect of a 1mm-thick plasma-sprayed yttria-stabilized zirconia (YSZ) coating on a piston. Such a coated piston and a similar steel piston are compared to each other based on experimental data for the heat release, the heat transfer rate to the oil in the piston cooling gallery, the local instantaneous surface temperature, and the local instantaneous surface heat flux. The surface temperature was measured for different crank angle positions using phosphor thermometry.

Biofuel can enable a sustainable transport solution and lower greenhouse gas emissions compared to standard fuels. This study focuses on biodiesel, implemented in the easiest way as drop in fuel. When mixing biodiesel into diesel one can run into problems with solubility causing contaminants precipitating out as insolubilities. These insolubilities, also called soft particles, can cause problems such as internal injector deposits and nozzle fouling. One way to overcome the problem of soft particles is by filtration. It is thus of great interest to be able to quantify fuel filters’ ability to intercept soft particles. The aim of this study is to test different fuel filters for heavy-duty engines and their ability to filter out synthetic soft particles. A custom-built fuel filter rig is presented, together with some of its general design requirements. For evaluation of the efficiency of the filters, fuel samples were taken before and after the filters.

Partially Premixed Combustion (PPC) is a combustion concept which aims to provide combustion with low smoke and NOx with high thermal efficiency. Extending the ignition delay to enhance the premixing, avoiding spray-driven combustion and controlling the combustion temperature at an optimum level through use of suitable lambda and EGR levels have been recognized as key factors to achieve such a combustion. Fuels with high ignitability resistance have been proven to be a useful to extend the ignition delay. In this work pure ethanol has been used as a PPC fuel. The objective of this research was initially to investigate the required operating conditions for PPC with ethanol. Additionally, a sensitivity analysis was performed to understand how the required parameters for ethanol PPC such as lambda, EGR rate, injection pressure and inlet temperature influence the combustion in terms of controllability, stability, emissions (i.e.

In the automotive industry, the piezo-based in-cylinder pressure sensor is getting commercialized and used in production vehicles. For example, the pressure sensor offers the opportunity to design algorithms for estimation of engine emissions, such as soot and NO , during a combustion cycle. In this paper a zero-dimensional NO model for a diesel engine is implemented that will be used in real time. The model is based on the thermal NO formation and the Zeldovich mechanism using two non-geometrical zones: burned and unburned zone. The influence of EGR on combustion temperature was modeled using a well-known thermodynamic identity where specific heat at constant pressure is included. Specific heat will vary with temperature and the gas composition. The model was implemented in LabVIEW using tools specific for an FPGA (Field-Programmable Gate Array).

Emissions of unburned methane are the Achilles heel of premixed gas engines whether they are spark ignited or diesel pilot ignited. If the engine is operated lean, lower temperatures prevail in the combustion chamber and several of the mechanisms behind the hydrocarbon emissions are aggravated. This paper presents an experimental investigation of the contribution from combustion chamber crevices and quenching to the total hydrocarbon emissions from a diesel-methane dual fuel engine at different operating conditions and air excess ratios. It is shown that the sensitivity to a change in topland crevice volume is greater at lean conditions than at stoichiometry. More than 70% of hydrocarbon emissions at air excess ratios relevant to operation of lean burn engines can be attributed to crevices.

In this work simulation results of a round spray jet are presented using the combination of Large-Eddy Simulation (LES) and Lagrangian Particle Tracking (LPT). The simulation setup serves as a synthetic model of non-atomizing spray particles taken from the Rosin-Rammler size distribution that enter a chamber filled with gas through an inlet hole with diameter D. At the inlet gas velocity and droplet velocities are specified in addition to the initial size distribution of droplets. The Reynolds number as referred to the gas inflow velocity and jet diameter is Re=10000. The setup is advantageous for understanding the details of diesel sprays since it avoids near-nozzle spray modeling and thereof the corresponding error which is especially important in LES. Here, the implicit LES is applied so that the compressible Navier-Stokes equations are solved directly with a numerical algorithm in a fine mesh without a subgrid scale model.

A diesel engine developed for an international market must be able to run on different fuels considering the diesel fuel qualities and the increasing selection of biofuels in the world. This leads to the question of how different fuels perform relative to a standard diesel fuel when not changing the hardware settings. In this study five fuels (Japanese diesel, MK3, EN590 with 10% RME, EN590 with 30% RME and pure RME) have been compared to a reference diesel fuel (Swedish MK1) when run on three different speeds and three different loads at each speed. The experiments are run on a Scania 13l Euro5 engine with standard settings for Swedish MK1 diesel. In general the differences were not large between the fuels. NO x usually increased compared to MK1 and then soot decreased as would be expected. The combustion efficiency increased with increased RME contents of the fuel but the indicated efficiency was not influenced by RME except for at higher loads.

Achieving upcoming HD emissions legislation, Euro VI/EPA 10, is a challenge for all engine manufacturers. A likely solution to meet the NOx limit is to use a combination of EGR and SCR. Combining these two technologies poses new challenges and possibilities when it comes to optimization and calibration. Using a complete system approach, i.e., considering the engine and the aftertreatment system as a single unit, is important in order to achieve good performance. Optimizing the complete system is a tedious task; first there are a large number of variables which affect both emissions and fuel consumption (injection timing, EGR rate, urea dosing, injection pressure, pilot/post injections, for example). Secondly, the chemical reactions in the SCR catalyst are substantially slower than the dynamics of the diesel engine and the rest of the system, making the optimization problem time dependent.

For diesel engines the major exhaust problem is particulate matter and NOx emissions. To reduce NOx, exhaust gas recirculation (EGR) is often used. The behavior of the EGR-level will therefore influence the emissions and it is therefore valuable to keep track of the EGR-level. Especially during transients it is difficult to predict how the EGR-level varies. In this paper the CO2-level in the intake is modeled on a 1-cylinder diesel engine to predict the in cylinder behavior during transients. The model is based on simple thermodynamics together with the ideal gas law. Using this, the model is validated by experimental data during transients and the correlation between model and experiment is shown to be strong. Furthermore, the total tank volume is decreased to achieve a faster mixing with the intention of simulating the behavior of the CO2-level in a full-size engine which has a higher gas flow.

Increasingly stringent emission legislation as well as increased demand on fuel efficiency calls for further research and development in the diesel engine field. Spray formation, evaporation and ignition delay are important factors that influence the combustion and emission formation processes in a diesel engine. Increased understanding of the mixture formation process is valuable in the development of low emission, high efficiency diesel engines. In this paper spray formation and ignition under real engine conditions have been studied in an optical engine capable of running close to full load for a real HD diesel engine. Powerful external lights were used to provide the required light intensity for high speed camera images in the combustion chamber prior to ignition. A specially developed software was used for spray edge detection and tracking. The software provides crank angle resolved spray penetration data.

A simplified combustion and emission formation model for diesel engines has been developed in a project where the long term objective is to predict emissions during transient operation. The intended application implies that the final model must be both computationally inexpensive and comprehensive so that it can be used for optimization of engine control variables when coupled to full-engine simulation software. As starting point, the proposed model uses diesel spray correlations established in combustion vessels regarding spray penetration, dispersion, gas entrainment, ignition and flame lift-off. It has been found that with minor adaption, these correlations are valid also for combustion in an engine. By assuming a fully mixing controlled combustion after ignition and by use of simplified emission models, the correlations have been found useful for predicting trends in engine-out emission with low computational cost.

During braking, both the rotor and the pads are worn in disc brakes. This wear process generates particles which may become airborne. In passenger car field tests it is difficult to distinguish these particles from others in the surrounding environment. It may therefore be preferable to use laboratory test stands and/or simulation models to study the amount of airborne wear particles generated. This paper discusses the possibility of predicting the number distribution of airborne wear particles generated from the pad to rotor contact in disc brakes by using general purpose finite element software. A simulation methodology is proposed where the particle coefficient is established by testing at material level. This coefficient is then used in numerical wear simulation at component level. The simulated number distribution is compared to experimental measurements at component level.

The tightening legislation in the on-road heavy-duty diesel area means that pollution control systems will soon be widely introduced on such engines. A number of different aftertreatment systems are currently being considered to meet the incoming legislation, including Diesel Particulate Filters (DPF), Diesel Oxidation Catalysts (DOC) and Selective Catalytic Reduction (SCR) systems. Relatively little is known about the interactions between lubricant-derived species and such aftertreatment systems. This paper describes the results of an experimental program carried out to investigate these interactions within DPF, DOC and SCR systems on a state-of-the-art 9 litre engine. The influence of lubricant composition and lube oil ash level was investigated on the different catalyst systems. In order to reduce costs and to speed up testing, test oil was dosed into the fuel. Tests without dosing lubricant into the fuel were also run.

Advanced functionalities unthinkable a few decades ago are now being introduced into automotive vehicles through embedded systems for reasons like emission control, vehicle connectivity, safety and cooperative behaviors. As the development often involves stakeholders from different engineering disciplines and organizations, the complexity due to shared requirements, interdependencies of data, functions, and resources, as well as tight constraints in regards to timing, safety, and resource efficiency makes the system integration, quality control and assurance, reuse and change management increasingly more difficult. This calls for a more rigorous approach to the development of automotive embedded systems and components.

Due to demanding legislation on exhaust emissions for internal combustion engines and increasing fuel prices, automotive manufacturers have focused their efforts on optimizing turbocharging systems. Turbocharger system control optimization is difficult: Unsteady flow conditions combined with not very accurate compressor maps make the real time turbocharger rotational speed one of the most important quantities in the optimization process. This work presents a methodology designed to obtain the turbocharger rotational speed via vibration analysis. Standard knock sensors have been employed in order to achieve a robust and accurate, yet still a low-cost solution capable of being mounted on-board. Results show that the developed method gives an estimation of the turbocharger rotational speed, with errors and accuracy acceptable for the proposed application. The method has been evaluated on a heavy duty diesel engine.