Search Results

Methanol-fueled diesels may be an attractive means of meeting future, more restrictive diesel particulate standards since methanol combustion forms very little soot. Unfortunately, methanol's autoignition temperature is high, and some means of improving its ignition is required. Therefore, we have investigated the use of dimethyl ether (DME), aspirated with the combustion air, to enhance the ignition of the injected methanol. A small, on-board catalytic reactor could be used to generate DME from the methanol fuel. This system requires minimal modifications to the engine design, and does not require use of an additive or fuel other than methanol. In this study, we measured maximum cylinder pressure and rate of pressure rise, ignition delay, emissions, and relative efficiencies for a single-cylinder, direct injection, high-speed diesel engine operated on both diesel fuel and methanol-DME.

The control of trace contaminants on the International Space Station (ISS) is carried out by a combination of activated carbon absorption and catalytic oxidation. The carbon bed absorbs most hydrocarbons, chloro and chlorofluorocarbons (CHCs and CFCs) while the catalytic oxidizer removes compounds such as methane, ethylene, ethane, and carbon monoxide that cannot be absorbed by the charcoal bed. Unfortunately, the Space Station catalyst of 0.5% palladium on alumina does not effectively oxidize CHCs and CFCs, and in fact is powerfully poisoned by them (Wright et al. 1996). Thus, even though the charcoal bed has little affinity for CFCs and CHCs, it must be sized to completely remove these compounds in order to protect the crew and prevent poisoning of the catalytic oxidizer. TDA Research Inc. (TDA), under contract to NASA-JSC, has designed, built, and tested an all-catalytic trace contaminant control system (TCCS) to be used in Phase III of the Early Human Testing Program.

Pressure-sensitive paint (PSP) technology is a technique used to experimentally determine surface pressures on models during wind tunnel tests. The key to this technique is a specially formulated pressure-sensitive paint that responds to, and can be correlated with the local air pressure. Wind tunnel models coated with pressure-sensitive paint are able to yield quantitative pressure data on an entire model surface in the form of light intensity values in recorded images. Quantitative results in terms of pressure coefficients (Cp) are obtained by correlating PSP data with conventional pressure tap data. Only a small number of surface taps are needed to be able to obtain quantitative pressure data with the PSP method. This technique is gaining acceptance so that future automotive wind tunnel tests can be done at reduced cost by eliminating most of the expensive pressure taps from wind tunnel models.

This paper summarizes the results to date of an on-going research program being conducted by NASA in conjunction with the FAA vertical flight program office. The goal of the program is to reduce pilot workload and increase safety for rotorcraft category A terminal area procedures. Two piloted simulations were conducted on the NASA Ames Vertical Motion Simulator to examine the benefits of optimal procedures, cockpit displays, and alternate cueing methods. Measures of performance, handling qualities ratings and pilot comments indicate that such enhancements can greatly assist a pilot in handling an engine failure in the terminal area.

Hover and ground-effect tests were conducted with the Lockheed-Martin Large Scale Powered Model (LSPM) during June-November 1995 at the Outdoor Aerodynamics Research Facility (OARF) located at NASA Ames Research Center. This was done in support of the Joint Strike Fighter (JSF) Program being lead by the Department of Defense. The program was previously referred to as the Joint Advanced Strike Technology (JAST) Program. The tests at the OARF included: engine thrust calibrations out of ground effect, measurements of individual nozzle jet pressure decay characteristics, and jet-induced hover force and moment measurements in and out of ground effect. The engine calibrations provide data correlating propulsion system throttle and nozzle settings with thrust forces and moments for the bare fuselage with the wings, canards, and tails removed. This permits measurement of propulsive forces and moments while minimizing any of the effects due to the presence of the large horizontal surfaces.

This paper describes research and development for reducing the aerodynamic drag of heavy vehicles by demonstrating new approaches for the numerical simulation and analysis of aerodynamic flow. In addition, greater use of newly developed computational tools holds promise for reducing the number of prototype tests, for cutting manufacturing costs, and for reducing overall time to market. Experimental verification and validation of new computational fluid dynamics methods are also an important part of this approach. Experiments on a model of an integrated tractor-trailer are underway at NASA Ames Research Center and the University of Southern California. Companion computer simulations are being performed by Sandia National Laboratories, Lawrence Livermore National Laboratory, and California Institute of Technology using state-of- the-art techniques, with the intention of implementing more complex methods in the future.

This paper describes research and development for reducing the aerodynamic drag of heavy vehicles by demonstrating new approaches for the numerical simulation and analysis of aerodynamic flow. Experimental validation of new computational fluid dynamics methods are also an important part of this approach. Experiments on a model of an integrated tractor-trailer are underway at NASA Ames Research Center and the University of Southern California (USC). Companion computer simulations are being performed by Sandia National Laboratories (SNL), Lawrence Livermore National Laboratory (LLNL), and California Institute of Technology (Caltech) using state-of-the-art techniques.