Refine Your Search

Topic

Search Results

Viewing 1 to 18 of 18
Training / Education

Fundamentals of GD&T for Inspectors 2-day

This course builds on geometric dimensioning and tolerancing fundamentals and teaches an introduction of how to inspect GD&T requirements. Utilizing the expertise of world-renowned GD&T expert Alex Krulikowski, this course offers an explanation of the geometric symbols, rules, and concepts, the datum system, and how to inspect GD&T requirements using tools from the four categories of inspection tools (CMM; comparison instruments and fixed gages; hand tools and open set up; and production gaging systems). Newly acquired learning is reinforced throughout the class with numerous practice problems.
Training / Education

Navigating Requirements for International Certification of Aviation Products

This course describes the basic elements of the process for achieving a successful aircraft certification globally once certification by the State of Design has been accomplished. The regulatory framework established under ICAO is presented with discussion of how major countries around the world comply with the ICAO Standards and Recommended Practices (SARPs). The uncertainty of how each country performs validation is a challenge. This course identifies common validation practices and key bilateral agreements which facilitate acceptance of aviation products from one country to another.
Training / Education

FAA/EASA Certification, Methods of Compliance for 29.801 Ditching

Certifying an aircraft, part or appliance can be a challenge. The FAA/EASA procedures can be frustrating and a maze of rules, policy and guidance. Understanding the process and procedures can provide you with a competitive edge and reduce your time obtaining a Certification approval. This course provides an overview of the Federal Aviation Administration (FAA) and European Aviation Safety Agency (EASA) policies, guidelines and requirements leading to Type and Supplemental Type airworthiness approvals. This course has a focus on 29.801 Ditching and EASA 29.802 Emergency Flotation.
Training / Education

Aircraft Virtual Flight Testing and Certification in Off-nominal Multifactorial Situations

The behavior of a 'pilot-automaton-aircraft-operating environment' system (the System) in off-nominal situations with multiple risks can be unpredictably dangerous. Most multifactorial flight scenarios (corner cases) are considered as theoretically improbable. Such anomalies do nonetheless occur in operations and can lead to inconceivable accidents - 'black swan' events.
Training / Education

FAA/EASA Certification, Methods of Compliance for 29.865 External Loads

Certifying an aircraft, part or appliance can be challenge. The FAA/EASA procedures can be frustrating and a maze of rules, policy and guidance. Understanding the process and procedures can provide you with a competitive edge and reduce your time obtaining a Certification approval. This course provides an overview of the Federal Aviation Administration (FAA) and European Aviation Safety Agency (EASA) policies, guidelines and requirements leading to Type and Supplemental Type airworthiness approvals. This course has a focus on 29.865 External loads to include hoists, belly-mounted external structure and cargo hook loads
Training / Education

AS13002 Qualifying an Alternate Inspection Frequency Plan

2021-06-28
AS13002 defines the process for qualifying an Alternate Inspection Frequency Plan for suppliers within the aero-engine sector. This two-day course will provide common requirements for developing and qualifying an alternate inspection plan, other than 100% inspection of all features. This course is designed to cover the basic elements of the process to be applied to design characteristics (as defined in AS9102), and parts or inspection processes as defined by the purchaser.
Training / Education

Fundamentals of GD&T 2018 3-day

2021-02-09
This course teaches the terms, rules, symbols, and concepts of GD&T as prescribed in the ASME Y14.5-2018 Standard. This course offers an in-depth explanation of geometric tolerancing symbols, their tolerance zones, applicable modifiers, common applications, and verification principles. The class includes a comparison of GD&T to the directly toleranced dimensioning method; Rules #1 and #2; form and orientation controls; tolerance of position; runout and profile controls. Newly acquired learning is reinforced throughout the class with more than 150 practice problems.
Standard

Air Cycle Air Conditioning Systems for Air Vehicles

2019-08-20
CURRENT
AS4073B
This SAE Aerospace Standard (AS) defines the requirements for air cycle air conditioning systems used on military air vehicles for cooling, heating, ventilation, and moisture and contamination control. General recommendations for an air conditioning system, which may include an air cycle system as a cooling source, are included in MIL-E-18927E and JSSG-2009. Air cycle air conditioning systems include those components which condition high temperature and high pressure air for delivery to occupied and equipment compartments and to electrical and electronic equipment. This document is applicable to open and closed loop air cycle systems. Definitions are contained in Section 5 of this document.
Standard

Automotive Gear Lubricants for Commercial and Military Use

2020-07-01
WIP
J2360
The gear lubricants covered by this standard exceed American Petroleum Institute (API) Service Classification API GL-5 and are intended for hypoid-type, automotive gear units, operating under conditions of high-speed/shock load and low speed/high-torque. These lubricants may be appropriate for other gear applications where the position of the shafts relative to each other and the type of gear flank contact involve a large percentage of sliding contact. Such applications typically require extreme pressure (EP) additives to prevent the adhesion and subsequent tearing away of material from the loaded gear flanks. These lubricants are not appropriate for the lubrication of worm gears. Appendix A is a mandatory part of this standard. The information contained in Appendix A is intended for the demonstration of compliance with the requirements of this standard and for listing on the Qualified Products List (QPL) administered by the Lubricant Review Institute (LRI).
Standard

Automotive Gear Lubricants for Commercial and Military Use

2019-01-07
CURRENT
J2360_201901
The gear lubricants covered by this standard exceed American Petroleum Institute (API) Service Classification API GL-5 and are intended for hypoid-type, automotive gear units, operating under conditions of high-speed/shock load and low-speed/high-torque. These lubricants may be appropriate for other gear applications where the position of the shafts relative to each other and the type of gear flank contact involve a large percentage of sliding contact. Such applications typically require extreme pressure (EP) additives to prevent the adhesion and subsequent tearing away of material from the loaded gear flanks. These lubricants are not appropriate for the lubrication of worm gears. Appendix A is a mandatory part of this standard. The information contained in Appendix A is intended for the demonstration of compliance with the requirements of this standard and for listing on the Qualified Products List (QPL) administered by the Lubricant Review Institute (LRI).
Magazine

Tech Briefs: October 2018

2018-10-01
Detecting Drones with Doppler-Based Radar Digital Transformation for a Connected Enterprise Using Electromagnetic Brakes to Keep Thrust Reversers in Place Thermostatic Solutions for Temperature Control Applications Bringing RF into the Embedded World: It's Time Compact Power Amplifier Solution for Electronic Warfare Burner Rig Testing of A500® C/SiC Test method simulates, in a laboratory environment, the service conditions ceramic-matrix composite material would experience in turbine engine exhaust applications. Space Debris Orbit and Attitude Prediction for Enhanced and Efficient Space Situational Awareness Developing accurate models to predict the behavior of manmade debris in space could be the key to preventing collisions with satellites. Maintaining Enterprise Resiliency Via Kaleidoscopic Adaption and Transformation of Software Services (MEERKATS) Implementing new technologies to create a more resilient, secure cloud computing environment.
Magazine

Tech Briefs: August 2018

2018-08-01
Designing a High-Speed Decoy Unmanned Aerial Vehicle (UAV) Using Thermoplastics in Aerospace Applications In-Flight Real-Time Avionics Adaptation Using Turbine Flow Meters for Aerospace Test and Measurement Applications Communicating from Space: The Front End of Multiscale Modeling Laser-Based System Could Expand Space-to-Ground Communication Hydraulic Testing of Polymer Matrix Composite 102mm Tube Section Research could lead to development of a composite material that can be processed at a low temperature and still be used at 1000°F. Permeation Tests on Polypropylene Fiber Materials Study attempts to determine if polypropylene nanofiber materials can be used in air filtration systems to remove toxic vapors. Inter-Laboratory Combat Helmet Blunt Impact Test Method Comparison Ensuring consistent test methods could reduce the risk of head injuries.
Standard

National Aerospace and Defense Contractors Accreditation Program Requirements for Stripping

1995-03-01
HISTORICAL
AS7109/4
This Aerospace Standard (AS) is to be used as a supplement to SAE AS7109. In addition to the requirements contained in AS7109, the requirements contained herein shall apply to suppliers seeking NADCAP Coatings accreditation who are engaged in stripping of coated material. The requirements for accreditation for the following classifications are contained herein: a. electrolytic; b. mechanical 1) grit blast 2) grinding and 3) machining; c. water jet; d. molten salt; and e. chemical.
Standard

National Aerospace and Defense Contractors Accreditation Program Requirements for Nonconventional Machining

2002-02-01
HISTORICAL
AS7116
This Aerospace Standard (AS) establishes the requirements for suppliers of Nonconventional Machining Services to be accredited by the National Aerospace and Defense Contractors Accreditation Program (NADCAP). NADCAP accreditation is granted in accordance with SAE AS7003 after demonstration of compliance with the requirements herein. The requirements may be supplemented by additional requirements specified by the NADCAP Nonconventional Machining and Surface Enhancement (NMSE) Task Group. Using the corresponding Audit Criteria (PRI AC7116) will ensure that accredited Nonconventional Machining suppliers meet all of the requirements in this standard and all applicable supplementary standards. The purpose of this audit program is to assess a supplier's ability to consistently provide a product or service that conforms to the technical specifications and customer requirements.
X