Refine Your Search

Search Results

Viewing 1 to 17 of 17
Standard

Overhead Protection for Agricultural Tractors - Test Procedures and Performance Requirements

1986-12-01
HISTORICAL
J167_198612
This SAE Standard applies to an overhead cover installed on a protective frame or enclosure conforming to SAE J2194 or alternately SAE J1194 and the following additional requirement of a drop test to verify the effectiveness of the overhead cover in protecting the operator from falling objects. The test procedures and performance requirements outlined in this document are based on currently available engineering data.
Standard

Safety for Agricultural Tractors

1977-06-01
HISTORICAL
J208C_197706
This standard is a guide to provide a reasonable degree of personal safety for operators and other persons during the normal operation and servicing of agricultural tractors.
Standard

Safety for Agricultural Tractors

1993-06-01
HISTORICAL
J208_199306
This standard is a guide to provide a reasonable degree of personal safety for operators and other persons during the normal operation and servicing of agricultural tractors.
Standard

Safety for Agricultural Tractors

1986-08-01
HISTORICAL
J208_198608
This standard is a guide to provide a reasonable degree of personal safety for operators and other persons during the normal operation and servicing of agricultural tractors.
Standard

Safety for Agricultural Tractors

1983-07-01
HISTORICAL
J208_198307
This standard is a guide to provide a reasonable degree of personal safety for operators and other persons during the normal operation and servicing of agricultural tractors.
Standard

Safety for Agricultural Tractors

1978-05-01
HISTORICAL
J208D_197805
This standard is a guide to provide a reasonable degree of personal safety for operators and other persons during the normal operation and servicing of agricultural tractors.
Standard

Safety for Agricultural Tractors

1996-08-01
CURRENT
J208_199608
This standard is a guide to provide a reasonable degree of personal safety for operators and other persons during the normal operation and servicing of agricultural tractors.
Standard

Roll-Over Protective Structures (ROPS) for Wheeled Agricultural Tractors

1993-06-01
HISTORICAL
J2194_199306
Any ROPS meeting the performance requirement of ISO 5700 (Static ROPS Test Standard) or ISO 3463 (Dynamic ROPS Test Standard) meets the performance requirements of this SAE Standard if the ROPS temperature/material and seat belt requirements of this document are also met. Fulfillment of the intended purpose requires testing as follows: A temperature-material requirement (6.9). This can be satisfied by using the appropriate materials or by performing any of the structural performance tests (Sections 7, 8, or 9) at -18 °C. A laboratory test, under repeatable and controlled loading, to permit analysis of the ROPS for compliance with the performance requirements of this document. Either the static test sequence (Section 7) or the impact test sequence (Section 8 ) shall be conducted. See Figure 1. A seat belt anchorage test (Section 10). The test procedures and performance requirements outlined in this document are based on currently available engineering data.
Standard

Roll-Over Protective Structures (ROPS) for Wheeled Agricultural Tractors

1987-12-01
HISTORICAL
J2194_198712
Any ROPS meeting the performance requirement of ISO 5700 (Static ROPS Test Standard) or ISO 3463 (Dynamic ROPS Test Standard) meets the performance requirements of this SAE Standard if the ROPS temperature/material and seat belt requirements of this document are also met. Fulfillment of the intended purpose requires testing as follows: A temperature-material requirement (6.9). This can be satisfied by using the appropriate materials or by performing any of the structural performance tests (Sections 7, 8, or 9) at -18 °C. A laboratory test, under repeatable and controlled loading, to permit analysis of the ROPS for compliance with the performance requirements of this document. Either the static test sequence (Section 7) or the impact test sequence (Section 8 ) shall be conducted. See Figure 1. A seat belt anchorage test (Section 10). The test procedures and performance requirements outlined in this document are based on currently available engineering data.
Standard

Roll-Over Protective Structures (ROPS) for Wheeled Agricultural Tractors

2002-08-29
HISTORICAL
J2194_200208
Any ROPS meeting the performance requirement of ISO 5700 (Static ROPS Test Standard) or ISO 3463 (Dynamic ROPS Test Standard) meets the performance requirements of this SAE Standard if the ROPS temperature/material and seat belt requirements of this document are also met. Fulfillment of the intended purpose requires testing as follows: A temperature-material requirement (6.9). This can be satisfied by using the appropriate materials or by performing any of the structural performance tests (Sections 7, 8, or 9) at -18 °C. A laboratory test, under repeatable and controlled loading, to permit analysis of the ROPS for compliance with the performance requirements of this document. Either the static test sequence (Section 7) or the impact test sequence (Section 8 ) shall be conducted. See Figure 1. A seat belt anchorage test (Section 10). The test procedures and performance requirements outlined in this document are based on currently available engineering data.
Standard

Roll-Over Protective Structures (Rops) for Wheeled Agricultural Tractors

1997-09-01
HISTORICAL
J2194_199709
Any ROPS meeting the performance requirement of ISO 5700 (Static ROPS Test Standard) or ISO 3468 (Dynamic ROPS Test Standard) meets the performance requirements of this SAE Standard if the ROPS temperature/material and seat belt requirements of this document are also met. Fulfillment of the intended purpose requires testing as follows: A temperature-material requirmenet. This can be satisfied by using the appropriate materials or by performing any of the structural performance tests at -18 degrees C. A laboratory test, under repeatable and controlled loading, to permit anaysis of the ROPS for compliance with the performance requirements of this document. Either the static test sequence or the impact test sequence shall be conducted. A set belt anchorage test. The test procedures and performance requirements outlined in this document are based on currently available engineering data.
Standard

Rollover Protective Structures (ROPS) for Wheeled Agricultural Tractors

1999-11-22
HISTORICAL
J1194_199911
Fulfillment of the intended purpose requires testing as follows: A laboratory test, under repeatable and controlled loading, to permit analysis of the ROPS for compliance with the performance requirements of this SAE Standard. Either the static test (6.1) or the dynamic test (6.2) shall be conducted. A crush test to verify the effectiveness of the deformed ROPS in supporting the tractor in an upset attitude. A field upset test under reasonably controlled conditions, both to the rear and side, to verify the effectiveness of the protective system under actual dynamic conditions. (See 6.4.1.1 for requirements for the omission of this test). In addition to the laboratory and field loading requirements, there is a temperature-material requirement. (See 7.1.2.) The test procedures and performance requirements outlined in this document are based on currently available engineering data.
Standard

Rollover Protective Structures (Rops) for Wheeled Agricultural Tractors

1994-09-01
HISTORICAL
J1194_199409
Fulfillment of the intended purpose requires testing as follows: a laboratory test, under repeatable and controlled loading, to permit analysis of the ROPS for compliance with the performance requirements of this SAE standard. Either the static test (5.1) or the dynamic test (5.2) shall be conducted; a crush test to verify the effectiveness of the deformed ROPS in supporting the tractor in an upset attitude; a field upset test under reasonable controlled conditions, both to the rear and side, to verify the effectiveness of the protective system under actual dynamic conditions. (See 5.4.1.1 for requirements for the omission of this test.); and in addition to the laboratory and field loading requirements, there is a temperature-material requirement. The test procedures and performance requirements outlined in this document are based on currently available engineering data.
Standard

Rollover Protective Structures (ROPS) for Wheeled Agricultural Tractors

1983-07-01
HISTORICAL
J1194_198307
Fulfillment of the intended purpose requires testing as follows: A laboratory test, under repeatable and controlled loading, to permit analysis of the ROPS for compliance with the performance requirements of this SAE Standard. Either the static test (6.1) or the dynamic test (6.2) shall be conducted. A crush test to verify the effectiveness of the deformed ROPS in supporting the tractor in an upset attitude. A field upset test under reasonably controlled conditions, both to the rear and side, to verify the effectiveness of the protective system under actual dynamic conditions. (See 6.4.1.1 for requirements for the omission of this test). In addition to the laboratory and field loading requirements, there is a temperature-material requirement. (See 7.1.2.) The test procedures and performance requirements outlined in this document are based on currently available engineering data.
Standard

Rollover Protective Structures (ROPS) for Wheeled Agricultural Tractors

1989-05-01
HISTORICAL
J1194_198905
Fulfillment of the intended purpose requires testing as follows: A laboratory test, under repeatable and controlled loading, to permit analysis of the ROPS for compliance with the performance requirements of this SAE Standard. Either the static test (6.1) or the dynamic test (6.2) shall be conducted. A crush test to verify the effectiveness of the deformed ROPS in supporting the tractor in an upset attitude. A field upset test under reasonably controlled conditions, both to the rear and side, to verify the effectiveness of the protective system under actual dynamic conditions. (See 6.4.1.1 for requirements for the omission of this test). In addition to the laboratory and field loading requirements, there is a temperature-material requirement. (See 7.1.2.) The test procedures and performance requirements outlined in this document are based on currently available engineering data.
Standard

Rollover Protective Structures (ROPS) for Wheeled Agricultural Tractors

1977-06-01
HISTORICAL
J1194_197706
Fulfillment of the intended purpose requires testing as follows: A laboratory test, under repeatable and controlled loading, to permit analysis of the ROPS for compliance with the performance requirements of this SAE Standard. Either the static test (6.1) or the dynamic test (6.2) shall be conducted. A crush test to verify the effectiveness of the deformed ROPS in supporting the tractor in an upset attitude. A field upset test under reasonably controlled conditions, both to the rear and side, to verify the effectiveness of the protective system under actual dynamic conditions. (See 6.4.1.1 for requirements for the omission of this test). In addition to the laboratory and field loading requirements, there is a temperature-material requirement. (See 7.1.2.) The test procedures and performance requirements outlined in this document are based on currently available engineering data.
X