Refine Your Search

Topic

Author

Affiliation

Search Results

Training / Education

Fundamentals of Motor Vehicle Fire Investigation

The manner in which a motor vehicle fire is initiated and subsequently spreads is dependent on a number of complex, interdependent, phenomena including combustion kinetics, heat transfer and fluid dynamics. Because the damage caused by a fire is coupled to these phenomena, damage patterns can sometimes be used to understand certain characteristics about the fire. In many cases, the goal is to determine the cause and origin of the fire.
Standard

SAE Electrical Energy Storage Device Labeling Recommended Practice

2012-12-07
CURRENT
J2936_201212
This SAE Recommended Practice provides for labeling guidelines at all levels of component, subsystem and system level architectures describing content, placement and durability requirements of specific unit throughout the total product life cycle from inception to reclamation.
Standard

Refrigerant 12 Automotive Air-Conditioning Hose

2015-04-21
CURRENT
J51_201504
This SAE Standard covers reinforced hose, or hose assemblies, intended for conducting liquid and gaseous dichlorodifluoromethane (refrigerant 12) in automotive air-conditioning systems. The hose shall be designed to minimize permeation of refrigerant 12 and contamination of the system and to be serviceable over a temperature range of −30 to 120 °C (−22 to 248 °F). Specific construction details are to be agreed upon between user and supplier.1 NOTE—R12 refrigerant has been placed on a banned substance list due to its ozone depletion characteristics. SAE J51 specification will be phased out as new automotive A/C systems are using R134a. SAE J2064 is the Standard for refrigerant 134a hose. For refrigerant 134a use, refer to SAE J2064.
Standard

Spark Arrester Test Carbon

1990-09-01
HISTORICAL
J997_199009
This SAE Standard establishes physical properties required of SAE Coarse Test Carbon and SAE Fine Test Carbon and establishes test methods to ensure that these requirements are met.
Standard

Spark Arrester Test Carbon

1988-06-01
HISTORICAL
J997_198806
This SAE Standard establishes physical properties required of SAE Coarse Test Carbon and SAE Fine Test Carbon and establishes test methods to ensure that these requirements are met.
Standard

Spark Arrester Test Carbon

1988-10-01
HISTORICAL
J997_198810
This SAE Standard establishes physical properties required of SAE Coarse Test Carbon and SAE Fine Test Carbon and establishes test methods to ensure that these requirements are met.
Standard

Low-Permeation Fuel Fill and Vent Tube

2007-07-02
CURRENT
J2405_200707
This SAE Standard covers the minimum requirements for a low-permeation tubing (100 g/m2·day or less) for use as a low pressure (14.5 kPa) liquid- or vapor-carrying component for use in gasoline or diesel fuel filler, vent, and vapor systems. The construction shall be designed to be functional over a temperature range of –40 °C to 100 °C for the T1 designation, or –40 °C to 125 °C for the T2 designation.
Standard

Fastener Part Standard - Hexagon Socket, Square Head, and Slotted Headless Set Screws - Inch Dimensioned

2016-11-15
CURRENT
J2656_201611
This SAE Part Standard covers selected inch dimensioned set screws manufactured in accordance with American Society for Mechanical Engineers dimensional standards. This SAE standard covers material most often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This standard permits the fasteners to be identified and ordered by a part identification number (PIN) as defined in this document.
Standard

SELECTION AND HEAT TREATMENT OF TOOL AND DIE STEELS

1970-04-01
HISTORICAL
J437_197004
The information in this report covers data relating to SAE J438, Tool and Die Steels, and is intended as a guide to the selection of the steel best suited for the intended purpose and to provide recommended heat treatments and other data pertinent to their use. Specific requirements as to physical properties are not included because the majority of tool and die steels are either worked or given special heat treatments by the purchaser. The purchaser may or may not elect to use the accompanying data for specification purposes.
Standard

Selection and Heat Treatment of Tool and Die Steels

2018-01-09
CURRENT
J437_201801
The information in this report covers data relating to SAE J438, Tool and Die Steels, and is intended as a guide to the selection of the steel best suited for the intended purpose and to provide recommended heat treatments and other data pertinent to their use. Specific requirements as to physical properties are not included because the majority of tool and die steels are either worked or given special heat treatments by the purchaser. The purchaser may or may not elect to use the accompanying data for specification purposes.
Standard

WROUGHT NICKEL AND NICKEL-RELATED ALLOYS

1976-07-01
HISTORICAL
J470_197607
This Report presents general information on over 50 alloys in which nickel either predominates or is a significant alloying element. It covers primarily wrought materials, and is not necessarily all inclusive. Values given are in most cases average or nominal, and if more precise values are required the producer(s) should be contacted. This report does not cover the so-called "superalloys," or the iron base stainless steels. Refer to SAE J467, Special Purpose Alloys, and SAE J405, Chemical Compositions of SAE Wrought Stainless Steels, respectively, for data on these alloys.
Standard

Wrought Nickel and Nickel-Related Alloys

2018-02-15
CURRENT
J470_201802
This Report presents general information on over 50 alloys in which nickel either predominates or is a significant alloying element. It covers primarily wrought materials, and is not necessarily all inclusive. Values given are in most cases average or nominal, and if more precise values are required the producer(s) should be contacted. This report does not cover the so-called "superalloys," or the iron base stainless steels. Refer to SAE J467, Special Purpose Alloys, and SAE J405, Chemical Compositions of SAE Wrought Stainless Steels, respectively, for data on these alloys.
Standard

PENETRATING RADIATION INSPECTION

1991-03-01
HISTORICAL
J427_199103
The purpose of this SAE Information Report is to provide basic information on penetrating radiation, as applied in the field of nondestructive testing, and to supply the user with sufficient information so that he may decide whether penetrating radiation methods apply to his particular inspection need. Detailed information references are listed in Section 2.
Standard

Penetrating Radiation Inspection

1988-12-01
HISTORICAL
J427_198812
The purpose of this SAE Information Report is to provide basic information on penetrating radiation, as applied in the field of nondestructive testing, and to supply the user with sufficient information so that he may decide whether penetrating radiation methods apply to his particular inspection need. Detailed information references are listed in Section 2.
X