Search Results

Most rollover literature is statistical in nature, focuses on reconstructed field data and experiences, or utilizes a very broad pool of dissimilar test data. When test data is presented, nearly all of it involves hard surface rollover tests performed at speeds near 30 mph, with a mix of passenger cars, sport utility vehicles and minivans. Five full-scale dolly rollover tests on dirt of production sport utility vehicles (SUV) and multi-purpose vehicles (MPV) were performed with similar input parameters. The similarities included Federal Motor Vehicle Safety Standard (FMVSS) 208 rollover dolly initiated events, level dirt rollover surfaces, and initiation speeds over 40 mph. All tests were recorded with multiple high-speed and real-time cameras. Additionally, some of the tests included detailed documentation of the rollover surface and the resulting evidence and debris patterns, as well as onboard angular rate sensing instrumentation.

Objective: A friction rollover test was conducted as part of a rollover sensing project. This study evaluates vehicle and occupant responses in the test. Methods: A flat dolly carried a Saab 9-3 sedan laterally, passenger-side leading to a release point at 42 km/h (26 mph) onto a high-friction surface. The vehicle was equipped with roll, pitch and yaw gyros near the center of gravity. Accelerometers were placed at the vehicle center tunnel, A-pillar near the roof, B-pillar near the sill, suspension sub-frame and wheels. Five off-board and two on-board cameras recorded kinematics. Hybrid III dummies were instrumented for head and chest acceleration and upper neck force and moment. Belt loads were measured. Results: The vehicle release caused the tires and then wheel rims to skid on the high-friction surface. The trip involved roll angular velocities >300 deg/s at 0.5 s and a far-side impact on the driver’s side roof at 0.94 s. The driver was inverted in the far-side, ground impact.

Rear impacts in the crash test data base compiled by the NHTSA are analyzed and compared to the CRASH3 rear stiffness coefficients. The CRASH3 values do not represent the test data adequately. This is because the values were derived from limited data, and because some of the rear moving barrier test data were miscoded as fixed barrier tests. A review of the larger NHTSA data base does not support the CRASH3 assumption that vehicles of similar size (wheelbase) have similar rear stiffness characteristics. Therefore, it is important when reconstructing individual accidents to use crash test data specific to the vehicles involved. Repeated rear fixed barrier test data on four vehicles are analyzed to study the data trend at speeds below and above the NHTSA test data. Constant stiffness and constant force models are compared and a combination of the two is shown to fit available test data.

The National Highway Traffic Safety Administration (NHTSA) has recently opened a rulemaking docket seeking comments on the design of automobile seats and their performance in rear Impacts. There are two philosophies of seat design: one advocates rigid seats, the other advocates seats which yield in a controlled manner. A review of the legislative history of seat back design standards indicates that yielding seats have historically been considered a better approach for passenger cars. The design characteristics of current production automobile seats are evaluated and show no significant changes over the past three decades. Concerns about the performance of rigid seat backs in real world rear impacts are discussed, specifically increased injury exposure due to ramping, rebound and out-of-position occupants.

Much has been written about reconstruction techniques and testing methods concerning vehicle rollovers. To date, most of the literature describes rollovers as one-dimensional events. Rollovers account for a disproportionate fraction of serious injuries and fatalities among all motor vehicle accidents. The three-dimensional nature of rollover sequences in which a rolling vehicle experiences multiple ground contacts contributes to the environment where such injuries occur. An analytical technique is developed to model the airborne segments of a rollover sequence as a parabolic path of the vehicle center of gravity. A formulation for the center of gravity descent from maximum elevation to full ground contact is developed. This formulation contains variables that may be readily determined from a thorough reconstruction. Ultimately, this formulation will also provide a vertical ground impact velocity at contact.

Research focusing on automotive rollovers has garnered a great deal of attention in recent years. Substantial effort has been directed toward the evaluation of rollover resistance. Issues related to crashworthiness, such as roof strength and restraint performance, have also received a great deal of attention. Much less research effort has been directed toward a more detailed study of the rollover dynamics from point-of-trip to point-of-rest. The reconstruction of rollover crashes often requires a thorough examination of the events taking place between point-of-trip and point-of-rest. Increasing demands are placed on reconstructionists to provide greater levels of detail regarding the roll sequence. Examples include, but are not limited to, roll rates at the quarter-roll level, CG trajectory (horizontal and vertical), roll angle at impact, and ground contact velocity. Often the detail that can be provided in a rollover reconstruction is limited by a lack of physical evidence.

The appropriateness of the set of eight frontal stiffness coefficients used by the CRASH3 program to estimate vehicle deformation energy (and to subsequently derive estimates of vehicle delta-V) is examined. This examination consists of constructing so-called CRASH energy plots based on 402 frontal fixed barrier impact tests contained in the NHTSA's Vehicle Test Center Data Base (VTCDB) digital tape file. It is concluded that the use of category coefficients within the CRASH3 program can result in large delta-V errors, reaffirming the inappropriateness of this program for use in individual accident reconstructions. The use of the CRASH3 category stiffness coefficients is seen to generally overestimate vehicle energy absorption for vehicles with small amounts of frontal crush and to underestimate vehicle energy absorption for vehicles sustaining large crush.

This paper summarizes work relating to the assessment of societal benefits of side impact protection. National Crash Severity Study (NCSS) and National Accident Sampling System (NASS) accident data technigues were reviewed with respect to the reliability of output information concerning the distribution of side impact accidents by impact severity and relationships between injury and impact severity. NCSS and NASS are confounded by errors and inadequacies, primarily as a result of improper accident reconstruction based upon the CRASH computer program. Based on review of several sample cases, it is believed that the NCSS/NASS files underestimate Lower severities and overestimate higher severities in side impact, with delta-V errors probably overestimated by 25-30 percent in the case of the more serious accidents. These errors cannot be properly quantified except on a case-by-case basis. They introduce unknown biases into NCSS/NASS.

The NHTSA notices of proposed rulemaking on side impact protection have focused worldwide attention on one of the most difficult and frustrating efforts in automobile crash safety. Traditional vehicle design has evolved obvious structural contrasts between the side of the struck vehicle and the front of the striking vehicle. Protection of near-side occupants from intruding door structure is a most perplexing engineering challenge. Much useful and insightful engineering work has been done in conjunction with NHTSA's proposed rulemaking. However, there are many major engineering issues which demand further definition before reasonable side impact rulemaking test criteria can be finalized. This paper reviews recent findings which characterize the human factors, biomechanics, and occupant position envelope of the typical side impact crash victim.

The original Malibu II study, conducted by Bahling et al, found that neck compression loading in rollover crashes is caused by the occupant moving toward the ground and therefore, roof crush was not causally related to the loading. Some have disputed this finding claiming that the occupant does not “dive toward the roof,” but rather, the roof “moves in” toward the occupant, and that roof deformation is the primary cause of cervical spine injuries in rollover crashes. The original study included a detailed analysis of film and force transducer data for 10 Potentially Injurious Impacts (PII's). This paper presents an independent analysis of these 10 PII's and one additional PII. This analysis uses the film and transducer data to evaluate the timing of roof deformation and neck loading, the magnitude of roof deformation at the time of peak neck load, and the motion of the vehicle and occupants in the inertial reference system.

Occupant simulation models have been used to study trends or specific design changes in “typical” accident modes such as frontal, side, rear, and rollover. This paper explores the usage of the Articulated Total Body Program (ATB) as an accident reconstruction tool. The importance of model validation is discussed. Specific areas of concern such as the contact model, force-deflection data, occupant parameters, restraint system models, head/neck loadings, padding, and intrusion are discussed in the context of accident reconstruction.

Based upon a review of the literature and new test data, the human and vehicle factors leading to head-to-roof contact in rollovers are quantified and illustrated. Vehicle design countermeasures and suggested areas of research are presented. Higher and stronger roofs and improved restraints must be analyzed as a system to evaluate the potential benefits in rollovers.

Automobile racing engine performance has historically progressed with and aided the development of automotive technology. Racing engine performance has been improved in various applications with specialized liquid fuels, such as nitroparaffins, alcohol (methanol) and certain hydrocarbons used in racing gasolines. This paper presents physical and thermodynamic properties of commonly used racing fuels and selected additives, including nitrous oxide and hydrazine. Improving the antiknock properties of gasoline for racing purposes is also discussed. Engine operating characteristics and power output for each fuel are discussed in terms of appropriate fuel properties and engine parameters such as air/fuel ratio and compression ratio. Combustion of various fuels is discussed along with the effect of dissociation and heat loss on performance. Some experimental performance data are presented, and theoretical and practical considerations which effect fuel utilization are also discussed.

The relatively rare occurrence of injury or fatality in fuel-fed fires has received considerable attention in automotive safety rulemaking and products liability litigation. The literature related to fatalities associated with fire is confirmed by recent FARS data, and there are no reliable field data which confirm a need for further injury-reducing effect related to FMVSS 301. NHTSA has acknowledged this by removing crash fire rulemaking from its priorities plan. The police-reported crash fire data now available must be supplemented with in-depth investigation by trained teams before informed judgements can be made regarding further safety improvements with respect to crash fire injury.

An economical alternative technique is presented for obtaining vehicle frontal crush characteristics from a series of repeated low speed barrier crashes. Results were analyzed using a technique of linear correlation of residual crush depth with a defined crush energy parameter. The data compared closely with crashes reported in the literature, and suggested that the structure exhibits only a slight strain rate sensitivity. Crush energy is shown to correlate well with dynamic crush depth. Relations among dynamic and residual crush and recovery distance are reported, Velocity restitution is shown to be about constant at 15% over the impact velocity range employed. A force-deflection relation based on the offset force linear harmonic oscillator theory is suggested, shown to agree quite well with data. Repeated crash testing can be an effective method to obtain information needed for development of analytical and predictive tools useful in design and reconstruction.

Collision Safety Engineering, Inc. (CSE), has developed a test prototype system to protect occupants during lateral impacts. It is an inflatable system that offers the potential of improved protection from thoracic, abdominal and pelvic injury by moving an impact pad into the occupant early in the crash. Further, it shows promise for head and neck protection by deployment of a headbag that covers the major target areas of B-pillar, window space, and roofrail before head impact. Preliminary static and full-scale crash tests suggest the possibility of injury reduction in many real-world crashes, although much development work remains before the production viability of this concept can be established. A description of the system and its preliminary testing is preceded by an overview of side impact injury and comments on the recent NHTSA Rule Making notices dealing with side-impact injury.

The issues of front seat energy absorption and seat belt effectiveness are investigated first through the review of prior experimental and analytical studies of rear impact dynamics. These prior studies indicate that the current energy absorption characteristic of seats is a safety benefit. Prior efforts to construct a rigidized seat indicate that such designs are likely to be impractical due to excessive weight and cost. Additionally, these studies indicate that seat belts provide an important safety function in rear impacts. Static tests of production seats were conducted, added to an existing data base, and analyzed to better understand the strength and energy absorbing characteristics of production seats. Crash test results from the New Car Assessment Program as well as earlier test programs were analyzed to describe the response of occupants and seats in rear impact and the protective function of seat belts in such collisions.

Recent detailed field accident data are examined with regard to injuries associated with rear impacts. The distribution of “Societal Harm” associated with various injury mechanisms is presented, and used to evaluate the performance of current seat back and restraint system designs. Deformation associated with seat back yield is shown to be beneficial in reducing overall Societal Harm in rear impacts. The Societal Harm associated with ejection and contact with the vehicle rear interior (the two injury mechanisms addressed by a rigid seat approach), is shown to be minimal. The field accident data also confirm that restraint usage in rear impacts has a substantial injury-reducing effect. Laboratory tests and computer simulations were run to investigate the mechanism by which seat belts protect occupants in rear impacts.

Understanding occupant kinematics is an important part of accident reconstruction, particularly with respect to injury causation. Injuries are generally sustained as the occupant interacts with the vehicle interior surfaces and is rapidly accelerated to the struck component's post-impact velocity. This paper describes some methods for assessing occupant kinematics in a collision, and discusses their limitations. A useful technique is presented which is based on free-body analysis and can be used to establish an occupant's path of motion relative to the vehicle, locate the point of occupant contact, and determine the occupant's velocity relative to that contact location.

The relationship between occupant crash injury and occupant compartment intrusion is seen in the perspectives of the velocity-time analysis and the NCSS statistical data for two important accident injury modes, lateral and rollover collisions. Restraint system use, interior impacts, and vehicle design features are considered. Side impact intrusion is analyzed from physical principles and further demonstrated by reference to staged collisions and NCSS data. Recent publications regarding findings of the NCSS data for rollovers, as well as the NCSS data itself, are reviewed as a background for kinematic findings regarding occupant injury in rollovers with roof crush.