Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

Connections for On-Board Road Vehicle Electrical Wiring Harnesses--Part 2: Tests and General Performance Requirements

2005-02-02
HISTORICAL
J2223/2_200502
This SAE Standard defines tests methods and general performance requirements of single-pole and multiple connectors for on-board electrical wiring harnesses of road vehicles. These requirements are not intended for connections internal to electronic devices. This document applies to connectors designed to be disconnected after mounting in the vehicle in the case of repair and/or maintenance.
Standard

Connections for On-Board Road Vehicle Electrical Wiring Harnesses - Part 2: Tests and General Performance Requirements

2018-10-22
WIP
J2223/2
Procedures included within this specification are intended to cover performance testing at all phases of development, production, and field analysis of electrical terminals, connectors, and components that constitute the electrical connection systems in low voltage (0 - 20 VDC) road vehicle applications. These procedures are only applicable to terminals used for In-Line, Header, and Device Connector systems with and without Shorting Bars. They are not applicable to Edge Board connector systems, greater than 20 VAC or DC, or to eyelet type terminals.
Standard

Connections for On-Board Road Vehicle Electrical Wiring Harnesses—Part 2: Tests and General Performance Requirements

2011-02-18
CURRENT
J2223/2_201102
Procedures included within this specification are intended to cover performance testing at all phases of development, production, and field analysis of electrical terminals, connectors, and components that constitute the electrical connection systems in low voltage (0 - 20 VDC) road vehicle applications. These procedures are only applicable to terminals used for In-Line, Header, and Device Connector systems with and without Shorting Bars. They are not applicable to Edge Board connector systems, > 20 VAC or DC, or to eyelet type terminals.
Standard

Primary Single Phase Nominal 120 VAC Wiring Distribution Assembly Design—Truck and Bus

2018-10-04
CURRENT
J2698_201810
This SAE Recommended Practice covers the design and application of primary on-board wiring distribution system harnessing for surface vehicles. This document is intended for single phase nominal 120 VAC circuits that provide power to truck sleeper cab hotel loads so that they may operate with the main propulsion engine turned off. The power supply comes from alternative sources such as land-based grid power, DC-AC inverters and auxiliary power generators. The circuits may also provide power to improve vehicle performance through charging batteries or operating cold-weather starting aids.
Standard

Primary Single Phase Nominal 120 VAC Wiring Distribution Assembly Design—Truck and Bus

2014-11-24
HISTORICAL
J2698_201411
This SAE Recommended Practice covers the design and application of primary on-board wiring distribution system harnessing for surface vehicles. This document is intended for single phase nominal 120 VAC circuits that provide power to truck sleeper cab hotel loads so that they may operate with the main propulsion engine turned off. The power supply comes from alternative sources such as land-based grid power, DC-AC inverters and auxiliary power generators. The circuits may also provide power to improve vehicle performance through charging batteries or operating cold-weather starting aids.
Standard

15 Pole Connector Between Towing Vehicles and Trailers with 12 Volt Nominal Supply

2013-04-09
HISTORICAL
J2691_201304
This SAE standard establishes the minimum construction and performance requirements for a 15 Pole Connector Between Towing Vehicles and Trailers, for trucks, trailers, and dollies in conjunction with SAE J2742 “Combination 11 Conductors and 4 Pairs ECBS Cable”. The connector accommodates both power and ISO 11992-1 signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.
Standard

15 Pole Connector Between Towing Vehicles and Trailers with 12 Volt Nominal Supply

2018-04-15
CURRENT
J2691_201804
This SAE standard establishes the minimum construction and performance requirements for a 15 Pole Connector Between Towing Vehicles and Trailers, for trucks, trailers, and dollies in conjunction with SAE J2742. The connector accommodates both power and ISO 11992-1 signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.
Standard

Electrical Terminals Blade Type

2001-12-01
HISTORICAL
J858_200112
Blade terminals listed in this SAE Recommended Practice may be used for terminating wire ends, or for terminating circuits on devices other than wire.
Standard

Bumper Jack Requirements--Motor Vehicles

1967-01-01
HISTORICAL
J979_196701
The following requirements and test information can be used to obtain reasonable quality and uniformity for bumper jacks. For this specification, a fully loaded vehicle includes curb weight, optional equipment, weight at 150 lb each for specified number of passengers, and a 150 lb load in the trunk. Vehicles with a gvw rating will be loaded to the maximum specified gvw.
X