Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

Vision Factors Considerations in Rearview Mirror Design

2009-02-13
HISTORICAL
J985_200902
The design and location of rear-viewing mirrors or systems, and the presentation of the rear view to the driver can best be achieved if the designer and the engineer have adequate references available on the physiological functions of head and eye movements and on the perceptual capabilities of the human visual system. The following information and charts are provided for this purpose. For more complete information of the relationship of vision to forward vision, see SAE SP-279.
Standard

Vision Factors Considerations in Rearview Mirror Design

2016-11-07
CURRENT
J985_201611
The design and location of rear-viewing mirrors or systems, and the presentation of the rear view to the driver can best be achieved if the designer and the engineer have adequate references available on the physiological functions of head and eye movements and on the perceptual capabilities of the human visual system. The following information and charts are provided for this purpose. For more complete information of the relationship of vision to forward vision, see SAE SP-279.
Standard

Bumper Jack Requirements--Motor Vehicles

1967-01-01
HISTORICAL
J979_196701
The following requirements and test information can be used to obtain reasonable quality and uniformity for bumper jacks. For this specification, a fully loaded vehicle includes curb weight, optional equipment, weight at 150 lb each for specified number of passengers, and a 150 lb load in the trunk. Vehicles with a gvw rating will be loaded to the maximum specified gvw.
Standard

Crane and Cable Excavator Basic Operating Control Arrangements

1998-10-01
CURRENT
J983_199810
This SAE Recommended Practice applies to mobile, construction type, crane and cable excavator hand and foot controls. It should not be construed to limit the use of, or to apply to combination controls, automatic controls, or any other special operating control requirements.
Standard

Ship Systems and Equipment--Part Standard for Studs--Continuous and Double End (Inch Series)

2009-01-23
HISTORICAL
J2271_200901
This SAE Parts Standard provides dimensional and quality assurance requirements for studs in the following configurations in standard materials used for ship system applications: a. Continuous thread studs in UNRC and 8UNR series in the following threads and diameters: - UNRC threads (0.190 through 4 inches) - UNRF threads (0.190 through 1-1/2 inches) - 8UNR threads (1-1/8 through 4 inches) b. Double end studs (clamping type) where both ends are of the same thread length in the following threads and diameters: - UNRC threads (1/4 through 4 inches) - UNRF threads (1/4 through 1-1/2 inches) - 8UNR threads (1-1/8 through 4 inches) c.
Standard

Ship Systems and Equipment - Part Standard for Studs - Continuous and Double End (Inch Series)

2004-06-21
HISTORICAL
J2271_200406
This SAE Parts Standard provides dimensional and quality assurance requirements for 1/4 through 2 in sizes of studs in the following configurations in standard materials used for ship system applications: a. Continuous thread studs in UNRC and 8UNR series. b. Double end studs (clamping type) where both ends are of the same thread series (UNRC or 8UN). Also called bolt-studs. (These are suitable for mating with nuts or the set end may be installed with anaerobic thread locking compound.) c. Double end studs (interference thread type) with the nut end having UNRC or 8UNR series thread and where the tap end has NC 5 HFS interference fit thread forms. Also called a tap end stud. A complete metric companion to this document is provided in SAE J2271M, therefore no metric equivalents are presented. These studs are primarily or use in ship systems and equipment.
Standard

Torque Ratings for Power Take-off Mounting Pads

2003-07-25
HISTORICAL
J2662_200307
This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.
X