Search Results

Selective catalytic reduction (SCR) catalysts will be used to reduce oxides of nitrogen (NOx) emissions from internal combustion engines in a number of applications [1,2,3,4]. Southwest Research Institute® (SwRI)® performed an Internal Research & Development project to study SCR catalyst thermal deactivation. The study included a V/W/TiO2 formulation, a Cu-zeolite formulation and an Fe-zeolite formulation. This work describes NOx timed response to ammonia (NH3) transients as a function of thermal aging time and temperature. It has been proposed that the response time of NOx emissions to NH3 transients, effected by changes in diesel emissions fluid (DEF) injection rate, could be used as an on-board diagnostic (OBD) metric. The objective of this study was to evaluate the feasibility and practicality of this OBD approach.

Classical diesel engine combustion with relatively short ignition delay, including papers dealing with low CR and high EGR calibrations. Papers describing experiments and test data, simulation results focused on applications, fuel/additive effects, combustion control, and mode change are part of this collections.

Abstract Introduction: This study evaluates driving ability in those with Charcot Marie Tooth Disease Type 1A, a hereditary peripheral neuropathy. Methods: Individuals with Charcot Marie Tooth Disease Type 1A (n = 18, age = 42 ± 7) and controls (n = 19; age = 35 ± 10) were evaluated in a driving simulator. The Charcot Marie Tooth Neuropathy Score version 2 was obtained for individuals. Rank Sum test and Spearman rank correlations were used for statistical analysis. Results: A 74% higher rate of lane departures and an 89% higher rate of lane deviations were seen in those with Charcot Marie Tooth Disease Type 1A than for controls (p = 0.005 and p < 0.001, respectively). Lane control variability was 10% higher for the individual group and correlated with the neuropathy score (rS = 0.518, p = 0.040), specifically sensory loss (rS = 0.710, p = 0.002) and pinprick sensation loss in the leg (rS = 0.490, p = 0.054).

Abstract Automotive-grade high-strength steels are galvanized for improved corrosion resistance. However, selective oxidation of alloying elements during annealing heat-treatment may influence the subsequent zinc (Zn) coating quality. The formation of internal and external oxides depends on the alloy composition, especially the Si/Mn ratio, and the oxygen potential of the annealing atmosphere. In this work, a dual-phase (DP) steel was intercritically annealed with varied fuel-to-air ratios in a direct-fired furnace and then galvanized in a Zn bath with 0.2 wt% Al. The type of internal and external oxides and the interfacial structures between the steel substrate, the Al-Fe-Zn inhibition layer, and the Zn coating were examined by using site-specific focused ion beam (FIB) and transmission electron microscopy (TEM).

The effect that thermally and compositionally stratified flowfields have on the spatial progression of iso-octane-fueled homogeneous charge compression ignition (HCCI) combustion were directly observed using highspeed chemiluminescence imaging. The stratified in-cylinder conditions were produced by independently feeding the intake valves of a four-valve engine with thermally and compositionally different mixtures of air, vaporized fuel, and argon. Results obtained under homogeneous conditions, acquired for comparison to stratified operation, showed a small natural progression of the combustion from the intake side to the exhaust side of the engine, a presumed result of natural thermal stratification created from heat transfer between the in-cylinder gases and the cylinder walls. Large differences in the spatial progression of the HCCI combustion were observed under stratified operating conditions.

A thorough understanding of vehicle exhaust aftertreatment system performance requires time-resolved emissions measurements that accurately follow driving transients, and that are correctly time-aligned with exhaust temperature and flow measurements. The transient response of conventional gas analyzers is characterized by both a time delay and an attenuation of high-frequency signal components. The distortion that this imposes on transient emissions measurements causes significant errors in instantaneous calculations of aftertreatment system efficiency, and thus in modal mass analysis. This creates difficulties in mathematical modeling of emissions system performance and in optimization of powertrain control strategies, leading to suboptimal aftertreatment system designs. A mathematical method is presented which improves the response time of emissions measurements. This begins with development of a model of gas transport and mixing within the sampling and measurement system.

Due to the stringent requirements to reduce the tail pipe emissions of NOx, Selective Catalytic Reduction (SCR) systems are used to remove NOx using ammonia. When a urea solution is injected into the exhaust system, urea will undergo hydrolysis and decomposition reaction that produces ammonia. At the catalyst surface, ammonia will react with the exhaust gases to convert NOx into nitrogen, N2 and water, H2O. One of the challenging problems is to make sure the urea solution is available for the SCR system at cold start conditions. At extreme cold temperatures, the urea solution will begin to freeze at −12°C. At the start up of a vehicle under such low ambient temperatures, a heating system is used to provide the heat required for melting the frozen urea. Therefore, there will be a time lag between the vehicle start up and the availability of urea solution to the SCR system.

The purpose of this document is to establish the requirements for Real-Time Communication Protocols (RTCP). Systems for real-time applications are characterized by the presence of hard deadlines where failure to meet a deadline must be considered a system fault. These requirements have been driven predominantly, but not exclusively, by aerospace type military platforms and commercial aircraft, but are generally applicable to any distributed, real-time, control systems. These requirements are primarily targeted for the Transport and Network Layers of peer to peer protocols, as referenced in the Open System Interconnect Reference Model (2.2.1 and 2.2.2), developed by the International Standards Organization (ISO). These requirements are intended to complement SAE AS4074 (2.1.1) and AS4075 (2.1.2), and future SAE communications standards.

The purpose of this document is to establish the requirements for Real-Time Communication Protocols (RTCP). Systems for real-time applications are characterized by the presence of hard deadlines where failure to meet a deadline must be considered a system fault. These requirements have been driven predominantly, but not exclusively, by aerospace type military platforms and commercial aircraft, but are generally applicable to any distributed, real-time, control systems. These requirements are primarily targeted for the Transport and Network Layers of peer to peer protocols, as referenced in the Open System Interconnect Reference Model (2.2.1 and 2.2.2), developed by the International Standards Organization (ISO). These requirements are intended to complement SAE AS4074 (2.1.1) and AS4075 (2.1.2), and future SAE communications standards.

Previous research has shown that elevating fuel injection pressure results in better air-fuel mixture formation, allowing for a further increase in maximum exhaust gas recirculation (EGR) rate while consequently reducing NOx emissions. The aim of this paper is to find out whether there is an optimum injection pressure for lowest soot-NOx emissions at a given boost pressure in high-speed diesel engines. Experiments are carried out on a single-cylinder research engine with a prototype common-rail system, capable of more than 200 MPa injection pressure. The effect of injection pressure on soot-NOx formation is investigated for a variety of boost conditions, representing the conditions of single to multi-stage turbocharger systems. Analysis of the data is performed at the application relevant soot to NOx ratio of approximately 1:10. It is observed that above a critical injection pressure, soot-NOx emissions are not reduced any further.

Simultaneous crank-angle-resolved measurements of gasoline concentration and gas temperature were made with two-color mid-infrared (mid-IR) laser absorption in a production spark-ignition engine (Nissan MR20DE, 2.0L, 4 cyl, MPI with premium gasoline). The mid-IR light was coupled into and out of the cylinder using fiber optics incorporated into a modified spark plug. The absorption line-of-sight was a 5.3 mm optical path located closely adjacent to the ignition spark providing spatially resolved absorption. Two sensor wavelengths were selected in the strong bands associated with the carbon-hydrogen (C-H) stretching vibration near 3.4 μm, which have an absorption ratio that is strongly temperature dependent. Fuel concentration and temperature were determined simultaneously from the absorption at these two wavelengths.

The post-flame oxidation of unburned hydrocarbons released from the ring-pack crevice was investigated for a small, air-cooled, spark-ignition utility engine. Spark timing sweeps were performed at 50, 75 and 100% load and speeds of 1800, 2400 and 3060 RPM while operating at a 12:1 air-fuel ratio, which is typical for these engines. A global HC consumption rate (GCR) was introduced based on the temporal profile of the mass released from the ring pack; the mass release after CA90 and up to the point where the remainder of the ring pack HC mass is equal to the exhaust HC level was taken as the mass oxidized, and a rate was defined based on this mass and the corresponding crank angle period over which this took place. For all conditions tested, the GCR varied with the spark timing; advanced spark timing gave higher GCR.

Lean burn natural gas engines have high potential in terms of efficiency and NOx emissions in comparison with stoichiometric natural gas engines, and much lower particulate emissions than diesel engines. They are a promising solution to meet the increasingly stringent exhaust emission targets for both light and heavy-duty engines. Partially Stratified-Charge (PSC) is a novel concept which was conceived by prof. Evans (University of British Columbia, Vancouver). This technique allows to further limit pollutant emissions and improve efficiency of an otherwise standard spark-ignition engine fuelled by natural gas, operating with lean air-fuel ratio. The potential of the PSC technique lies in the control of load without throttling by further extending the lean flammability limit.

Different optimization strategies for the optimization of the calibration of a turbocharged GDI engine through numerical simulation were analyzed, aiming to evaluate the opportunities offered by direct optimization techniques. A one-dimensional fluid dynamic engine model was used to predict engine performance, taking into account knock and exhaust temperature constraints. Air fuel ratio, spark advance, boost pressure and cam phasing were optimized by means of different optimization strategies, including direct search as well as numerical methods. Both full load (with maximum bmep targets) and part load (with minimum bsfc targets) were considered.

In HCCI engines, the Air/Fuel Ratio (AFR) and Residual Gas Fraction (RGF) are difficult to control during the SI-HCCI-SI transition, and this may result in incomplete combustion and/or high pressure raise rates. As a result, there may be undesirably high engine load fluctuations. The objectives of this work are to further understand this process and develop control methods to minimize these load fluctuations. This paper presents data on instantaneous AFR and RGF measurements, both taken by novel experimental techniques. The data provides an insight into the cyclic AFR and RGF fluctuations during the switch. These results suggest that the relatively slow change in the intake Manifold Air Pressure (MAP) and actuation time of the Variable Valve Timing (VVT) are the main causes of undesired AFR and RGF fluctuations, and hence an unacceptable Net IMEP (NIMEP) fluctuation. We also found large cylinder-to-cylinder AFR variations during the transition.

In pursuit of reducing dependencies on foreign oil coupled with U.S. renewable fuel standards and an overall focus and interest in greenhouse gas emissions, investigations continue on feasibility of replacement biologically derived fuels such as ethanol and butanol. Majority of existing recreational products such as marine outboard engines, boats, personal watercraft, all terrain vehicles and snowmobiles are carbureted or operate open-loop, meaning the engine does not have the capability to sense air-fuel ratio. Ethanol has a specific energy content that is less than gasoline. Without means to compensate for air-fuel ratio requirements of specific fuels, open-loop engines may suffer from a condition known as enleanment, in which catastrophic engine failure may result. On the contrary, butanol has specific energy content closer to that of gasoline, suggesting open-loop engines may be less prone to negative effects of increased biologically derived fuel concentrations in gasoline.

Engine downsizing has become one of the main strategies to reduce C02 emission. Turbochargers are well-adapted to this purpose but one of their biggest drawbacks is the turbo-lag which reduces the driving comfort especially during acceleration. Electrically driven compressors also known as E-compressor or E-booster could be a well-adapted solution to boost the engine intake pressure in order to reduce the turbo-lag. Since centrifugal compressors operate at high rotational speeds, high speed electric machines are therefore required. To achieve a significant reduction of the turbo-lag, a very fast response time is needed leading to the development of electric machines able to typically spin from idle to 75kRPM in less than 300ms. With 20 years of expertise in the development of innovative brushless DC motors for automotive applications, MMT has recently investigated the design of such high power-high rotation speed motors.

Regarding the strongly growing two-wheeler market fuel economy, price and emission legislations are in focus of current development work. Fuel economy as well as emissions can be improved by introduction of engine management systems (EMS). In order to provide the benefits of an EMS for low cost motorcycles, efforts are being made at BOSCH to reduce the costs of a port fuel injection (PFI) system. The present paper describes a method of how to reduce the number of sensors of a PFI system by the use of sophisticated software functions based on high-resolution engine speed evaluation. In order to improve the performance of a system working without a MAP-sensor (manifold air pressure sensor) an air charge feature (ACFn) based on engine speed is introduced. It is shown by an experiment that ACFn allows to detect and adapt changes in manifold air pressure. Cross-influences on ACFn are analyzed by simulations and engine test bench measurements.

Using a 109.2 cm3, four-stroke, single-cylinder, two-valve gasoline engine, improvement of fuel economy by extension of lean burn range has been attempted with invented way to intensify tumble flow from a simple mechanical arrangement. With a part of the intake valve was jutted out beyond the perimeter of the cylinder bore, the masking effects from the valve recess on top of the cylinder sleeve created a strong tumble flow, which enabled lean burn at an air fuel ratio leaner than the conventional design by two points. The motorcycle equipped with this engine attained better fuel economy by 5.7% to the base model when measured in Indian Driving Cycle (IDC). The outward-laid intake valve also increased the clearance from the exhaust valve, which enabled use of a large-diameter intake valve to minimize the reduction of maximum power.