Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

Top Speed Test Procedure for Electric Motorcycles

2014-02-21
CURRENT
J3007_201402
This SAE Recommended Practice incorporates a track-based test procedure that produces a representative value for vehicle top speed when operating on a level paved road with a fully charged battery.
Standard

Refrigerant 12 Automotive Air-Conditioning Hose

2015-04-21
CURRENT
J51_201504
This SAE Standard covers reinforced hose, or hose assemblies, intended for conducting liquid and gaseous dichlorodifluoromethane (refrigerant 12) in automotive air-conditioning systems. The hose shall be designed to minimize permeation of refrigerant 12 and contamination of the system and to be serviceable over a temperature range of −30 to 120 °C (−22 to 248 °F). Specific construction details are to be agreed upon between user and supplier.1 NOTE—R12 refrigerant has been placed on a banned substance list due to its ozone depletion characteristics. SAE J51 specification will be phased out as new automotive A/C systems are using R134a. SAE J2064 is the Standard for refrigerant 134a hose. For refrigerant 134a use, refer to SAE J2064.
Standard

Connections for On-Board Road Vehicle Electrical Wiring Harnesses - Part 1: Single-Pole Connectors - Flat Blade Terminals - Dimensional Characteristics and Specific Requirements

2011-12-20
CURRENT
J2223/1_201112
This SAE Standard specifies dimensional characteristics of flat blades of single-pole connectors and specific requirements for on-board electrical harnesses of road vehicles, which can be fitted into female connectors such as those given as in Appendix A. This document applies to connectors designed to be disconnected after mounting in the vehicle in the case of repair and/or maintenance only.
Standard

Snowmobile Stop Lamp

2011-03-12
CURRENT
J278_201103
This document provides test methods and requirements for the stop lamp on snowmobiles.
Standard

Low-Permeation Fuel Fill and Vent Tube

2007-07-02
CURRENT
J2405_200707
This SAE Standard covers the minimum requirements for a low-permeation tubing (100 g/m2·day or less) for use as a low pressure (14.5 kPa) liquid- or vapor-carrying component for use in gasoline or diesel fuel filler, vent, and vapor systems. The construction shall be designed to be functional over a temperature range of –40 °C to 100 °C for the T1 designation, or –40 °C to 125 °C for the T2 designation.
Standard

SELECTION AND HEAT TREATMENT OF TOOL AND DIE STEELS

1970-04-01
HISTORICAL
J437_197004
The information in this report covers data relating to SAE J438, Tool and Die Steels, and is intended as a guide to the selection of the steel best suited for the intended purpose and to provide recommended heat treatments and other data pertinent to their use. Specific requirements as to physical properties are not included because the majority of tool and die steels are either worked or given special heat treatments by the purchaser. The purchaser may or may not elect to use the accompanying data for specification purposes.
Standard

Selection and Heat Treatment of Tool and Die Steels

2018-01-09
CURRENT
J437_201801
The information in this report covers data relating to SAE J438, Tool and Die Steels, and is intended as a guide to the selection of the steel best suited for the intended purpose and to provide recommended heat treatments and other data pertinent to their use. Specific requirements as to physical properties are not included because the majority of tool and die steels are either worked or given special heat treatments by the purchaser. The purchaser may or may not elect to use the accompanying data for specification purposes.
Standard

WROUGHT NICKEL AND NICKEL-RELATED ALLOYS

1976-07-01
HISTORICAL
J470_197607
This Report presents general information on over 50 alloys in which nickel either predominates or is a significant alloying element. It covers primarily wrought materials, and is not necessarily all inclusive. Values given are in most cases average or nominal, and if more precise values are required the producer(s) should be contacted. This report does not cover the so-called "superalloys," or the iron base stainless steels. Refer to SAE J467, Special Purpose Alloys, and SAE J405, Chemical Compositions of SAE Wrought Stainless Steels, respectively, for data on these alloys.
Standard

Wrought Nickel and Nickel-Related Alloys

2018-02-15
CURRENT
J470_201802
This Report presents general information on over 50 alloys in which nickel either predominates or is a significant alloying element. It covers primarily wrought materials, and is not necessarily all inclusive. Values given are in most cases average or nominal, and if more precise values are required the producer(s) should be contacted. This report does not cover the so-called "superalloys," or the iron base stainless steels. Refer to SAE J467, Special Purpose Alloys, and SAE J405, Chemical Compositions of SAE Wrought Stainless Steels, respectively, for data on these alloys.
Standard

Fastener Part Standard - Machine Screw Nuts (Metric and Inch)

2012-12-20
CURRENT
J2485_201212
This SAE Part Standard covers selected machine screw nuts manufactured in accordance with American Society for Mechanical Engineers (ASME) dimensional standards. This document covers material most often used in ship systems and equipment but its use may be applied wherever nuts of the covered materials are used. This document permits the nuts to be identified and ordered by a part identification number (PIN) as defined in this document.
Standard

Power Steering Pressure Hose - Low Volumetric Expansion Type

2014-09-09
CURRENT
J191_201409
This SAE Standard covers hose fabricated from fabric braid and synthetic rubber, assembled with end fittings for use in automotive power steering applications at pressures as indicated in Table 1B, as flexible connections within the temperature range of -40 °C (-40 °F) to 121°C (250 °F) average, 135 °C (275 °F) maximum peaks. These hoses are intended for use in applications where reduction in amplitude of pump pressure pulsations is not required.
Standard

Power Steering Pressure Hose - High Volumetric Expansion Type

2012-07-05
CURRENT
J188_201207
This document covers two types of hose fabricated from fabric braid and synthetic rubber, assembled with end fittings for use in automotive power steering applications as flexible connections within the temperature range of -40 °C to +120 °C (-40 °F to +250 °F) average, and 135 °C (275 °F) maximum peaks. These hoses are intended for use in applications where reduction in amplitude of pump pressure pulsations is required. Type 1 hose shall be suitable for 10.3 MPa (1500 psi) maximum working pressure. Type 2 hose shall be suitable for 10.3 MPa (1500 psi) maximum working pressure.
Standard

Power Steering Return Hose - Low Pressure

2012-07-05
CURRENT
J189_201207
This SAE Standard covers hose fabricated from fabric braid and synthetic rubber, assembled with end fittings or user applied clamps for use in automotive power steering applications as flexible connections within the temperature range of -40 °C to +120 °C (-40 °F to 250 °F) average and 135 °C (275 °F) maximum peaks. Hose assemblies shall be suitable for 1.72 MPa (250 psi) maximum working pressure with end fittings and 0.69 MPa (100 psi) maximum working pressure with user applied clamps.
Standard

Classification System for Thermoplastic Elastomers

2005-10-10
HISTORICAL
J2558_200510
This SAE Standard provides a system for specifying significant material properties of thermoplastic elastomers (TPEs) that are intended for, but not limited to, use in automotive applications. NOTE 1—For the purposes of this document a TPE is defined as a polymeric material that, without further chemical modifications, is capable of recovering from deformations quickly and forcibly and is also capable of being repeatedly softened by heating and hardened by cooling within a temperature range characteristic of the material. NOTE 2—When the TPE product is to be used for purposes where the requirements are too specific to be completely prescribed by this classification system, it is necessary for the purchaser to consult the supplier in advance to establish the appropriate properties, test methods, and specification test limits.
Standard

Instrusion Resistance of Safety Glazing Systems for Road Vehicles

2001-04-24
HISTORICAL
J2568_200104
This SAE Recommended Practice specifies an intrusion resistance test method for glazing systems installed in motor vehicles. Intrusion resistance performance is determined not solely by the glazing but also by the glazing attachment to the vehicle and by the vehicle structure. Therefore, the glazing/ attachment /vehicle structure must be tested as a single unit. This test determines intrusion resistance only. The test applies to those materials that meet the requirements for use as safety glazing materials as specified in Safety Standard ANSI/SAE Z26.1 or other applicable standards. The test applies to all installation locations.
Standard

Intrusion Resistance of Safety Glazing Systems for Road Vehicles

2003-02-12
HISTORICAL
J2568_200302
This SAE Recommended Practice specifies an intrusion resistance test method for glazing systems installed in motor vehicles. Intrusion resistance performance is determined not solely by the glazing but also by the glazing attachment to the vehicle and by the vehicle structure. Therefore, the glazing/ attachment /vehicle structure must be tested as a single unit. This test determines intrusion resistance only. The test applies to those materials that meet the requirements for use as safety glazing materials as specified in Safety Standard ANSI/SAE Z26.1 or other applicable standards. The test applies to all installation locations.
Standard

Positive Temperature Coefficient Overcurrent Protection Devices (PTCs)

2014-12-03
CURRENT
J2685_201412
This SAE Recommended Practice defines the test conditions, procedures, and performance requirements for PTC (positive temperature coefficient of resistance) overcurrent protection devices. PTCs are typically either polymeric (PPTC) or ceramic (CPTC). It is important to note battery voltages versus powernets/system voltage versus max battery voltages: (12 V/14 V/16 V, 24 V/28 V/32 V, and 36 V/42 V/58 V). All voltages are DC. These devices are typically rated with a maximum operating voltage, which for vehicular systems need to be 16 V (for 12 V batteries), 32 V (for 24 V batteries), and 58 V (for 36 V batteries/42 V powernets). PTC devices are considered to be self-resetting after responding to overcurrent conditions and after such condition has been removed from the affected circuit containing the PTC.
X