Search Results

The field of motor vehicle rollover research and testing has been one of multiple and varied approaches, dating back to at least the 1930's. The approach has been as simple as tipping a vehicle over at the top of a steep hill ( Wilson et al., 1972 ), to as complex as releasing a vehicle from an elevated roll spit mounted to the rear of a moving tractor and trailer ( Cooper et al., 2001 and Carter et al., 2002 ). Presenter Peter Luepke, P Luepke Consulting

APPLICATION: Premium quality bolts and screws for use up to 600 F (315 C) where a high strength lightweight fastener is required.

Abstract In motorcycles, when they are traveling at medium to high speed, the roll stability is usually maintained by the restoration force generated by self-steering effect. However, when the vehicle is stationary or traveling in low speed, sufficient restoring force does not occur because some of the forces, such as centrifugal force, become small. In our study, we aimed at prototyping a motorcycle having a roll stability realized by a steering control when the vehicle is stationary or traveling in low speed. When we considered a mathematical control model to be applied, general models of four-degree-of-freedom had a critical inconvenience that the formulae include nonlinear second derivatives making them excessively complicated for deriving a practically applicable control method. Accordingly, we originally constructed a new control model which has equivalent two point masses (upper and lower from the vehicle’s center of gravity).

Abstract The suspension system has been shown to have significant effects on vehicle performance, including handling, ride, component durability, and even energy efficiency during the design process. In this study, a new roll-plane hydraulically interconnected suspension (HIS) system is proposed to enhance both roll and lateral dynamics of a two-axle bus. The roll-plane stability analysis for the HIS system has been intensively explored in a number of studies, while only few efforts have been made for suspension tuning, especially considering lateral plane stability. This article aims to explore the integrated lateral and roll dynamics by suspension tuning of a two-axle bus equipped with HIS system. A ten-degree-of-freedom (DOF) lumped-mass vehicle model is integrated with either transient mechanical-hydraulic model for HIS or the traditional suspension components, namely, shock absorber and anti-roll bar (ARB).

This specification covers an aluminum alloy in the form of bars and rods 0.500 inch (12.7 mm) to 8.000 inches (203.2 mm) in nominal diameter or least difference between parallel sides and up to 50 square inches (322.6 square centimeters) in cross-sectional area (see 8.7).

The purpose of this document is to provide guidance on in-flight thrust determination of engines that are impacted by intentional or unintentional thrust vectoring. However, as indicated in the Foreword, the field of aircraft thrust vectoring is varied and complex. For simplicity and coherence of purpose, this document will be limited in scope to multi-axis thrust vectoring nozzles or vanes attached to the rear of the engine or airfame; single-axis thrust vectoring and unintentional thrust vectoring (fixed shelf or deck configuration) are special cases of this discussion. Specifically excluded from this scope are thrust vectoring created primarily by airframe components such as wing flaps, etc.; lift engines, propulsive fans and thrust augmenting ejectors; and powerplants that rotate or otherwise move with respect to the airframe.

This SAE Information Report describes results of testing of the SAE J1746 ISP-Vehicle Standard for the communication of spatial data references between central sites and mobile vehicles on roads. Testing was performed by the Oak Ridge National Laboratory and its contractors, resulting in a document from which this Information Report has been extracted. Tests were performed by computer analysis and corroborated by field tests with a mobile vehicle.

This specification covers one type of high-contrast, medium-grain radiographic film in the form of cut sheets or rolls.

This specification covers one type of high-contrast, medium-grain radiographic film in the form of cut sheets or rolls.

This paper describes an effective integrated method for estimation of subject-specific mass, inertia tensor, and center of mass of individual body segments of a digital avatar for use with physics-based digital human modeling simulation environment. One of the main goals of digital human modeling and simulation environments is that a user should be able to change the avatar (from male to female to a child) at any given time. The user should also be able to change the various link dimensions, like lengths of upper and lower arms, lengths of upper and lower legs, etc. These customizations in digital avatar's geometry change the kinematic and dynamic properties of various segments of its body. Hence, the mass and center of mass/inertia data of the segments must be updated before simulating physics-based realistic motions. Most of the current methods use mass and inertia properties calculated from a set of regression equations based on average of some population.

A truck-trailer combination is modeled using ADAMS/Car from MSC Software for handling and ride comfort performance simulations. The handling events include a double lane change and lateral roll stability. The ride comfort performance events include several sized half-rounds and various RMS courses. The variables for handling performance evaluation include lateral acceleration, roll angles and tire patch normal loads. The variables for ride performance evaluation are absorbed power and peak acceleration. This study considers the trailer spring stiffness, anti-roll bar and jounce bumper gap as the design variables. Through DOE simulations, we derived the response surface models of various performance variables so that we could consider the performance sensitivities to the design variables.

The ride performance potentials of a prototype torsio-elastic axle suspension for an off-road vehicle were investigated analytically and experimentally. A forestry vehicle was fitted with the prototype suspension at its rear axle to assess its ride performance benefits. Field measurements of ride vibration along the vertical, lateral, fore-aft, roll and pitch axes were performed for the suspended and an unsuspended vehicle, while traversing a forestry terrain. The measured vibration responses of both vehicles were evaluated in terms of unweighted and frequency-weighted rms accelerations and the acceleration spectra, and compared to assess the potential performance benefits of the proposed suspension. The results revealed that the proposed suspension could yield significant reductions in the vibration magnitudes transmitted to the operator's station.

The wear of thrust 51100 rolling bearings was investigated and their dissipative responses in a bench test rig were associated to their heating, elastic energy of mechanical vibration and Sound Pressure Level [dB], regarding two greases, both from the same supplier, being one with graphite and the other with Molybdenum Disulfide. The samples were commercially acquired and submitted to a normal load of 450±5N and 3100±30 CPM, determined after the screening tests. Four variables were measured: temperature [K], electrical power [W], global velocity vibration [mm/s] and Sound Pressure Level [dB]. After 106 cycles, the tracks were analyzed by Optical Microscopy. The bearings lubricated with the grease with graphite showed different responses in relation to the ones lubricated with MoS2 thrust bearings. The signal of the signatures and the damage morphology are presented and discussed.

The authors have developed a measurement technique using a new digital telemeter which measures the piston secondary motion as ensuring high accuracy while under the operation. We applied this new digital telemeter to several measurements and analysis on the piston secondary motion that can cause piston noises, and here are some of the results from our measurement. We have confirmed that these piston motions vary by only several tenths of millimeter changes of the piston specifications such as the piston-pin offset and the center of gravity of the piston. As in other cases, we have found that a mere change of pressure in the crankcase or the amount of lubricating oil supplied on the cylinder bore varies the piston motion that may give effect on the piston noises.

This paper employs the motion-mode energy method (MEM) to investigate the effects of a roll-plane hydraulically interconnected suspension (HIS) system on vehicle body-wheel motion-mode energy distribution. A roll-plane HIS system can directly provide stiffness and damping to vehicle roll motion-mode, in addition to spring and shock absorbers in each wheel station. A four degree-of-freedom (DOF) roll-plane half-car model is employed for this study, which contains four body-wheel motion-modes, including body bounce mode, body roll mode, wheel bounce mode and wheel roll mode. For a half-car model, its dynamic energy contained in the relative motions between its body and wheels is a sum of the energy of these four motion-modes. Numerical examples and full-car experiments are used to illustrate the concept of the effects of HIS on motion-mode energy distribution.

A method for the measurement of the full mass properties of vehicles and subsystems is presented. The knowledge of the center of gravity location and of the inertia tensor of vehicles and subsystems is fundamental for performing accurate dynamic simulations, ranging from handling to durability. The accurate estimation of the inertia tensor can be achieved primarily via experimental tests. Given a rigid body and its mass, the proposed method allows to measure the center of mass location and the inertia tensor during a single test. The proposed technique is based on the analysis of the free motion of a multi-cable pendulum to which the vehicle or the subsystem is connected. The body under test is made rotating around three axes passing nearby the body center of mass with a highly non linear motion.

The (Vehicle Inertia Parameter Evaluation Rig) VIPER II is a full vehicle mass and inertia parameter measurement machine. The VIPER II expands upon the capabilities of its predecessor and is capable of measuring vehicles with a mass of up to 45,360 kg (100,000 lb), an increase in capacity of 18,100 kg (40,000 lb). The VIPER II also exceeds its predecessor in both the length and width of vehicles it can measure. The VIPER II's maximum vehicle width is 381 cm (150 in) an increase of 76 cm (30 in) and maximum distance from the vehicle CG to the outer most axle is 648 cm (255 in) an additional 152 cm (60 in) The VIPER II is capable of performing measurements including vehicle CG height, pitch, roll, and yaw moments of inertia and the roll/yaw cross product of inertia. While being able to measure both heavier and larger vehicles, the VIPER II is designed to maintain a maximum error of 3% for all inertia measurements and 1% for CG height.

This paper proposes a new integrated chassis control (ICC) using a predictive model-based control (MPC) for optimal allocation of sub-chassis control systems where a predictive model has 6 Degree of Freedom (DoF) for rigid body dynamics. The 6 DoF predictive vehicle model consists of longitudinal, lateral, vertical, roll, pitch, and yaw motions while previous MPC research uses a 3 DoF maximally predictive model such as longitudinal, lateral and yaw motions. The sub-chassis control systems in this paper include four wheel individual braking torque control, four wheel individual driving torque control and four corner active suspension control. Intermediate control inputs for sub-chassis control systems are simplified as wheel slip ratio changes for driving and braking controls and vertical suspension force changes for an active suspension control.