Refine Your Search

Topic

Author

Affiliation

Search Results

Training / Education

Introduction to Advanced High Strength Steel Applications and Manufacturing

2019-10-08
Advanced High Strength Steels (AHSS) are now commonly used in automotive body structural applications. The high strength of this grade classification is attractive to help reduce mass in the automotive body through reduction in thickness. Strength also supports improvements in safety requirements so that mass increases are minimized. In some specific grades of AHSS, energy absorption is possible in addition to the high strength. This course will review the definition and properties of AHSS and cover several common applications in automotive body structures.
Standard

A Tilt Table Procedure for Measuring the Static Rollover Threshold for Heavy Trucks

2011-05-17
CURRENT
J2180_201105
The test procedure applies to roll coupled units such as straight trucks, tractor semitrailers, full trailers, B-trains, etc. The test is aimed at evaluating the level of lateral acceleration required to rollover a vehicle or a roll-coupled unit of a vehicle in a steady turning situation. Transient, vibratory, or dynamic rollover situations are not simulated by this test. Furthermore, the accuracy of the test decreases as the tilt angle increases, although this is a small effect at the levels of tilt angle used in testing heavy trucks. The test accuracy is accepted for vehicles that will rollover at lateral acceleration levels below 0.5 g corresponding to a tilt table angle of less than approximately 27 degrees. Even so, the results for heavy trucks with rollover thresholds greater than 0.5 g could be used for comparing their relative static roll stability.
Standard

Braking Performance - Asphalt Pavers

2012-09-12
HISTORICAL
J2118_201209
This SAE Standard specifies brake system performance and test criteria to enable uniform evaluation of the braking capability of self-propelled, rubber-tired and tracked asphalt pavers. Service, secondary, and parking brakes are included.
Standard

Braking Performance - Asphalt Pavers

2018-10-04
CURRENT
J2118_201810
This SAE Standard specifies brake system performance and test criteria to enable uniform evaluation of the braking capability of self-propelled, rubber-tired and tracked asphalt pavers. Service, secondary, and parking brakes are included.
Video

SAE Eye on Engineering: Ford's new steel-bodied Ranger

2018-11-08
Today, ford motor company begins U.S. production of its 2019 Ranger, the company's first midsize pickup. In this episode of SAE Eye on Engineering, Editor-in-Chief Lindsay Brooke looks at the new steel-bodied Ranger. SAE Eye on Engineering also airs Monday mornings on WJR 760 AM Detroit's Paul W. Smith Show.
Standard

Categorization of Low Carbon Automotive Sheet Steel

1997-09-15
CURRENT
J2096_199709
This SAE Recommended Practice establishes a nomenclature for categorizing low carbon automotive hot rolled sheet, cold rolled sheet, and zinc and zinc alloy coated sheets.
Standard

SAE MANUAL ON BLAST CLEANING

1968-06-01
CURRENT
J792A_196806
Blast cleaning may be defined as a secondary manufacturing process in which a suitable stream of solid particles is propelled with sufficient velocity against a work surface to cause a cleaning or abrading action when it comes in contact with the workpiece. As indicated in the definition, blast cleaning may be employed for a variety of purposes. Ordinarily, it is considered as a method for removing sand from castings, burrs or scale from forgings, mill products, or heat treated parts; to promote machinability, and to minimize the possibility of interference in actual operation. In addition to this use, blast cleaning also produces an excellent surface for industrial coatings. All these objectives are often accomplished in the one operation.
Standard

Nomenclature--Industrial and Agricultural Mowers

1986-05-01
HISTORICAL
J990_198605
This Standard provides names of many of the major components and parts peculiar to agricultural and industrial rotary, flail and sickle bar type mowers. Illustrations used are not intended to include all existing industrial or agricultural machines, or to be exactly descriptive of any particular machine. They have been picked to describe the principles to be used in applying this standard.
Standard

Engine Rotation and Cylinder Numbering

1986-01-01
HISTORICAL
J824_198601
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
Standard

Crane Hoist Line Speed and Power Test Procedure

2017-06-07
CURRENT
J820_201706
This document applies primarily to mobile cranes that lift loads by means of a drum and hoist line mechanism. It can be used to determine the hoist line speed and power of other hoist line mechanisms, if the load can be held constant and hoist line travel distance is sufficient for the accuracy of the line speed measurements prescribed. This recommended practice applies to all mechanical, hydraulic, and electric powered hoist mechanisms.
Standard

Crane Hoist Line Speed and Power Test Code

1998-07-01
HISTORICAL
J820_199807
This code applies primarily to mobile cranes that lift loads by means of a drum and hoist line mechanism. It can be used to determine the hoist line speed and power of other hoist line mechanisms, if load can be held constant and hoist line travel distance is sufficient for the accuracy of the line speed measurements prescribed.
Standard

Split Type Bushings – Design and Application

2011-06-13
CURRENT
J835_201106
This SAE Standard presents the standard sizes, important dimensions, specialized measurement techniques, and tolerances for split type bushings. Both SI and inch sizes are shown; their dimensions are not exact equivalents. New designs shall use SI units. Unless specifically stated as ±, all tolerances are total.
Standard

Push-On Hose and Mating Hose Fittings

2014-06-06
CURRENT
J2552_201406
SAE J2552 provides limited, dimensional and general performance requirements for low pressure, field attachable, push-on hose and their mating hose fittings. The intended application is for fluid and pneumatic power used with petroleum base hydraulic fluids, lube oils, water glycols and air, within the temperature ranges listed in Table 1. The maximum working pressure is 1.7 MPa (see Table 2). For air applications the maximum working pressure is at 0.7 MPa. Hose and hose fittings are manufactured within certain dimensions with tolerance ranges in order to provide the proper gripping and sealing. SAE J2552 hose from one manufacturer may not be compatible with SAE J2552 hose fittings supplied by another manufacturer. It is the responsibility of the fabricator to always follow the manufacturers’ instructions for proper preparation and fabrication of hose assemblies.
Standard

Ship Systems and Equipment—Part Standard for Studs—Continuous and Double End (Inch Series)

2009-05-04
CURRENT
J2271_200905
This SAE Parts Standard provides dimensional and quality assurance requirements for studs in the following configurations in standard materials used for ship system applications: a Continuous thread studs in UNRC and 8UNR series in the following threads and diameters: UNRC threads (1/4 through 4 inches) UNRF threads (1/4 through 1-1/2 inches) 8UNR threads (1-1/8 through 4 inches) b Double end studs (clamping type) where both ends are of the same minimum thread length in the following threads and diameters: UNRC threads (1/4 through 4 inches) UNRF threads (1/4 through 1-1/2 inches) 8UNR threads (1-1/8 through 4 inches) Different thread forms on each end are permissible. c Double end studs (tap end type) where the tap end thread length is equivalent to 1-1/2 nominal diameters: Tap End Thread Forms and Diameters Nut End Thread Forms and Diameters NC-5 interference-fit tap end threads (1/4 through 1-1/2 inches) UNRC threads (1/4 through 4 inches) UNRC threads (1/4 through 4 inches) UNRF threads (1/4 through 1-1/2 inches) UNRF threads (1/4 through 1-1/2 inches) 8UNR threads (1-1/8 through 4 inches) 8UNR threads (1-1/8 through 4 Inches)
X