Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

R134a Refrigerant Charge Determination Test Method

2018-09-11
CURRENT
J3023_201809
The purpose of this document is to establish guidelines for determining the critical R134a refrigerant charge for off-road, self-propelled work machines as defined in SAE J1116 and Agricultural Tractors as defined in ANSI/ASAE S390. It will develop a minimum to maximum refrigerant charge range in which the HVAC system can maintain proper operation. Operating conditions and characteristics of the equipment will influence the optimum charge. Since these conditions and characteristics vary greatly from one application to another, careful consideration should be taken to determine the optimum R134a refrigerant charge for the HVAC system.
Standard

Measurement of Passenger Compartment Refrigerant Concentrations Under System Refrigerant Leakage Conditions

2011-02-04
CURRENT
J2772_201102
This Standard is restricted to refrigeration circuits that provide air-conditioning for the passenger compartments of passenger and commercial vehicles. This Standard includes analytical and physical test procedures to evaluate concentration inside the passenger compartment. In the early phases of vehicle evaluation, usage of the analytical approach may be sufficient without performing physical tests. The physical test procedure involves releasing refrigerant from an external source to a location adjacent to the evaporator core (inside the HVAC-Module). An apparatus is used to provide a repeatable, calibrated leak rate. If the system has multiple evaporators, leakage could be simulated at any of the evaporator locations. This standard gives detail information on the techniques for measuring R-744 [CO2] and R-1234yf [HFO-1234yf], but the general techniques described here can be used for other refrigerants as well.
Standard

Top Speed Test Procedure for Electric Motorcycles

2014-02-21
CURRENT
J3007_201402
This SAE Recommended Practice incorporates a track-based test procedure that produces a representative value for vehicle top speed when operating on a level paved road with a fully charged battery.
Standard

Air Dryer Test Procedure

2012-11-09
CURRENT
J2384_201211
This SAE Recommended Practice establishes uniform Test Procedures for desiccant Air Dryers used in vehicles with compressed air systems per SAE J2383. Continuous flow desiccant Air Dryers are excluded from the scope of this document.
Standard

SAE MANUAL ON BLAST CLEANING

1968-06-01
CURRENT
J792A_196806
Blast cleaning may be defined as a secondary manufacturing process in which a suitable stream of solid particles is propelled with sufficient velocity against a work surface to cause a cleaning or abrading action when it comes in contact with the workpiece. As indicated in the definition, blast cleaning may be employed for a variety of purposes. Ordinarily, it is considered as a method for removing sand from castings, burrs or scale from forgings, mill products, or heat treated parts; to promote machinability, and to minimize the possibility of interference in actual operation. In addition to this use, blast cleaning also produces an excellent surface for industrial coatings. All these objectives are often accomplished in the one operation.
Standard

Diesel Injection Pump Testing—Part 2: Orifice Plate Flow Measurement

2015-09-22
CURRENT
J968/2_201509
This part of SAE J968 specifies the flow measuring system, including the fixture, to be used for flow testing the single hole orifice plates used in an orifice plate type nozzle and holder assembly (described in SAE J968-1) which is intended for testing and setting diesel fuel injection pumps on test benches. The flow measuring system and fixture ensure accurate flow testing of the entire range of orifices from 0.4 to 0.8 mm diameter as specified in SAE J968-1. It is intended primarily for use by the manufacturers of single hole orifice plates.
Standard

Diesel Injection Pump Testing—Part 2: Orifice Plate Flow Measurement

2002-12-20
HISTORICAL
J968/2_200212
This part of SAE J968 specifies the flow measuring system, including the fixture, to be used for flow testing the single hole orifice plates used in an orifice plate type nozzle and holder assembly (described in SAE J968-1) which is intended for testing and setting diesel fuel injection pumps on test benches. The flow measuring system and fixture ensure accurate flow testing of the entire range of orifices from 0.4 to 0.8 mm diameter as specified in SAE J968-1. It is intended primarily for use by the manufacturers of single hole orifice plates.
Book

Nonlinear and Hybrid Systems in Automotive Control

2003-05-01
A new generation of strategies for vehicle and engine control systems has become necessary because of increasing requirements for accuracy, ride, comfort, safety, complexity, and emission levels. In contrast with earlier systems, new control systems are based on dynamic physical models and the principles of advanced nonlinear control. With contributions from leading scientists in the field, this book presents an overview of research in this rapidly-expanding area. New approaches to solving theoretical problems, as well as numerous systems and control research issues, are covered.
Standard

Brake System Road Test Code - Passenger Car and Light-Duty Truck

2013-03-28
CURRENT
J843_201303
This SAE Recommended Practice establishes a uniform procedure for the level road test of the brake systems of new light-duty trucks and new multipurpose passenger vehicles1 up to and including 2700 kg (6000 lb) GVW and all classes of new passenger cars.
Standard

Voltage Regulators for Automotive-Type Generators

2006-01-09
CURRENT
J2669_200601
This SAE Definition Document contains historic voltage regulation methods and test requirements that have not been previously published. The purpose of this document is to recommend a set of definitions and practices for use on current and future 12 V vehicle electric power regulation and control systems in internal combustion engine road vehicles. This document is not intended to include nor exclude regulators used in higher voltage vehicle electrical systems. The term “generator” rather than “alternator” will be used even though these terms may be used interchangeably in practice.
Standard

Pneumatic Spring Terminology

2016-04-01
CURRENT
J511_201604
This pneumatic spring terminology has been developed to assist engineers and designers in the preparation of specifications and descriptive material relating to pneumatic springs and their components. It does not include gas supply or control systems.
Standard

PNEUMATIC SPRING TERMINOLOGY

1989-06-01
HISTORICAL
J511_198906
This pneumatic spring terminology has been developed to assist engineers and designers in the preparation of specifications and descriptive material relating to pneumatic springs and their components. It does not include gas supply or control systems.
Standard

SINTERED CARBIDE TOOLS

1977-02-01
HISTORICAL
J439_197702
This recommended practice covers methods for measuring or evaluating five properties or characteristics of sintered carbide which contribute significantly to the performance of sintered carbide tools. These properties are: hardness, specific gravity, apparent porosity, structure, and grain size. They are covered under separate headings below.
Standard

Sintered Carbide Tools

2018-01-09
CURRENT
J439_201801
This recommended practice covers methods for measuring or evaluating five properties or characteristics of sintered carbide which contribute significantly to the performance of sintered carbide tools. These properties are: hardness, specific gravity, apparent porosity, structure, and grain size. They are covered under separate headings below.
Standard

Maximum Sound Level Potential for Motorcycles

2011-08-04
CURRENT
J47_201108
This SAE Recommended Practice establishes the test procedure, environment, and instrumentation for determining the maximum sound level potential for motorcycles under wide open throttle acceleration and closed throttle deceleration.
Standard

Rated (Advertised) Fuel Capacity - Passenger Car, Multi-Purpose Passenger Vehicles, and Light Duty Trucks

2012-11-01
CURRENT
J398_201211
This recommended practice provides a method for establishing the rated or advertised fuel capacity for a vehicle utilizing liquid fuel at atmospheric pressure. It applies to passenger cars, multi-purpose passenger vehicles and light duty trucks (10 000 lb (4536 kg) maximum GVW), (Ref. SAE J1100). It also includes a standardized procedure for creating a full tank when another test requires that condition as a starting point. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.
X