Refine Your Search

Search Results

Standard

ABS Excitor Ring Location Standardization

2004-07-27
HISTORICAL
J1730_200407
This SAE Recommended Practice is to establish the Antilock Brake System (ABS) sensor interface and envelope dimensions for standardizing the location of the Antilock Brake System (ABS) rings mounted on the inner end of the hub on the following axle designations. a. FF front b. FL front c. L powered rear d. R powered rear e. U powered rear f. W powered rear g. N trailer h. P trailer
Standard

ABS Exciter Ring Location Standardization

2012-03-15
CURRENT
J1730_201203
This SAE Recommended Practice establishes the Antilock Brake System [ABS] sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on the inner end of spoke wheels, hubs and hub-rotor assemblies on the following axle designations. FF FL FC FH L R U W N P
Standard

ABS Excitor Ring Location Standardization

1996-10-01
HISTORICAL
J1730_199610
This SAE Recommended Practice is to establish the Antilock Brake System (ABS) sensor interface and envelope dimensions for standardizing the location of the Antilock Brake System (ABS) rings mounted on the inner end of the hub on the following axle designations: a. FF front; b. FL front; c. L powered rear; d. R powered rear; e. U powered rear; f. W powered rear; g. N trailer and h. P trailer. This document provides standardized wheel end Antilock Brake System (ABS) sensor interface dimensions for spoke wheels and hubs intended for normal highway use on trucks, buses, truck trailers, and multipurpose passenger vehicles.
Standard

ABS Excitor Ring Location Standardization

1999-10-09
HISTORICAL
J1730_199910
This SAE Recommended Practice is to establish the Antilock Brake System (ABS) sensor interface and envelope dimensions for standardizing the location of the Antilock Brake System (ABS) rings mounted on the inner end of the hub on the following axle designations. a. FF front b. FL front c. L powered rear d. R powered rear e. U powered rear f. W powered rear g. N trailer h. P trailer
Standard

ABS Exciter Ring Location Standardization

2018-01-16
WIP
J1730
This SAE Recommended Practice establishes the Antilock Brake System [ABS] sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on the inner end of spoke wheels, hubs and hub-rotor assemblies on the following axle designations. a. FF b. FL c. FC d. FH e. L f. R g. U h. W j. N k. P
Standard

Dimensions--Wheels for Demountable Rims, Demountable Rims,and Spacer Bands--Commercial Vehicles

2001-07-31
HISTORICAL
J851_200107
This SAE Recommended Practice establishes dimensions for wheels for demountable rims, demountable rims, and rim spacers. The dimensions given are those necessary to maintain serviceability and interchangeability of the demountable rims, rim spacers, and wheels for demountable rims. Special and less common applications are not covered in this recommended practice.
Standard

Dimensions--Wheels for Demountable Rims, Demountable Rims, and Spacer Bands--Truck and Bus

2007-09-07
HISTORICAL
J851_200709
This SAE Recommended Practice establishes dimensions for wheels for demountable rims, demountable rims, and rim spacers. The dimensions given are those necessary to maintain serviceability and interchangeability of the demountable rims, rim spacers, and wheels for demountable rims. Special and less common applications are not covered in this recommended practice.
Standard

Dimensions - Wheels for Demountable Rims, Demountable Rims, and Spacer Bands - Truck and Bus

1987-06-01
HISTORICAL
J851_198706
This SAE Recommended Practice establishes dimensions for wheels for demountable rims, demountable rims, and rim spacers. The dimensions given are those necessary to maintain serviceability and interchangeability of the demountable rims, rim spacers, and wheels for demountable rims. Special and less common applications are not covered in this recommended practice.
Standard

Dimensions - Wheels for Demountable Rims, Demountable Rims, and Spacer Bands - Truck and Bus

2011-03-30
CURRENT
J851_201103
This SAE Recommended Practice establishes dimensions for wheels for demountable rims, demountable rims, and rim spacers. The dimensions given are those necessary to maintain serviceability and interchangeability of the demountable rims, rim spacers, and wheels for demountable rims. Special and less common applications are not covered in this recommended practice.
Standard

Balance Weight and Rim Flange Design Specifications, Test Procedures, and Performance Recommendations for Heavy Vehicle Applications

2018-04-12
WIP
J3172
This SAE Recommended Practice is intended to serve as a guide for standardization of features, dimensions, and configurations of balance weights for aluminum and steel wheels intended for use on Heavy Truck/Vehicles (Class 5-8) to assure good installation and retention of the balance weight. This document also provides test procedures and minimum performance requirements for testing balance weight retention.
Standard

Biaxial Wheel Fatigue Test - Truck, Bus, and Trailer

2013-03-11
WIP
J3036
To provide uniform laboratory procedures and radial/lateral load pairs for biaxial fatigue testing of disc wheel intended for normal highway use on trucks, buses, and trailers applicable for the North America market. Load cases considered include steer, drive, and trailer vehicle positions. The radial/lateral load pairs are not specific to one particular vehicle or OEM manufacturer.
Standard

Inboard Mounted Disc Brake Rotor/Disc Wheel Hub Interface Dimensions - Commercial Vehicles

2012-05-29
CURRENT
J2696_201205
This SAE Recommended Practice establishes dimensions and tolerances for the interface between inboard mounted disc brake rotors and disc wheel hubs. The geometric features described in this document are shown at true position. This document is intended for inboard mounted disc brake rotors and disc wheel hubs for Class 5, 6, 7, and 8 commercial vehicles. Special and less common applications are not covered.
Standard

Inboard Mounted Disc Brake Rotor/Disc Wheel Hub Interface Dimensions - Commercial Vehicles

2018-01-16
WIP
J2696
This SAE Recommended Practice establishes dimensions and tolerances for the interface between inboard mounted disc brake rotors and disc wheel hubs. The geometric features described in this document are shown at true position. This document is intended for inboard mounted disc brake rotors and disc wheel hubs for Class 5, 6, 7, and 8 commercial vehicles. Special and less common applications are not covered.
Standard

Dimensional Compatibility for Commercial Vehicle Wheels to Air Disc Brake Calipers—Truck and Bus

2018-01-10
WIP
J2803
This SAE Recommended Practice defines the boundary line for establishing dimensional compatibility between air disc brake calipers and 22.5 inch diameter disc wheels and includes valve stem consideration. The line establishes the minimum wheel with valve stem envelope to allow interchangeability. This document addresses dimensional characteristics only and makes no reference to the performance, operational dynamic deflections or heat dissipation of the system. It is up to the system integrator to ensure sufficient clearance exists between the caliper, wheel and valve stem to provide safe operating conditions. Mounting systems as noted are referenced in SAE J694.
Standard

Wheels/Rims - Military Vehicles - Test Procedures and Performance Requirements

2012-04-23
CURRENT
J1992_201204
This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of disc wheels, demountable rims, and bolt-together divided wheels intended for normal highway use on military trucks, buses, truck-trailers, and multipurpose vehicles. For wheels and rims intended for normal highway use on trucks and buses, see SAE J267. For wheels intended for normal highway use on passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. This document does not cover off-highway or other special application wheels and rims.
Standard

Wheels/Rims--Military Vehicles--Test Procedures and Performance Requirements

2001-03-31
HISTORICAL
J1992_200103
This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of disc wheels, demountable rims, and bolt-together wheels intended for normal highway use on military trucks, buses, truck-trailers, and multipurpose vehicles. For wheels and rims intended for normal highway use by trucks, see SAE J267. For wheels intended for normal highway use by passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. This document does not cover off-highway or other special application wheels and rims.
Standard

Wheels/Rims - Military Vehicles - Test Procedures and Performance Requirements

2017-06-19
WIP
J1992
This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of disc wheels, demountable rims, and bolt-together divided wheels intended for normal highway use on military trucks, buses, truck-trailers, and multipurpose vehicles. For wheels and rims intended for normal highway use on trucks and buses, see SAE J267. For wheels intended for normal highway use on passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. This document does not cover off-highway or other special application wheels and rims.
Standard

Dimensions-Wheels for Demountable Rims, Demountable Rims and Spacer Bands-Commercial Vehicles

1995-12-01
HISTORICAL
J851_199512
This SAE Recommended Practice establishes dimensions for wheels for demountable rims, demountable rims, and rim spacers. The dimensions given are those necessary to maintain serviceability and interchangeability of the demountable rim, rim spacer, and wheels for demountable rims. Special and less common applications are not covered in this recommended practice.
Standard

Wheel End Assembly and Axle Spindle Interface Dimensions--Truck and Bus

2018-05-02
WIP
J2475

This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, seal and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, N, P, R, U, and W.

Standard

Wheel End Assembly and Axle Spindle Interface Dimensions--Truck and Bus

2000-01-24
HISTORICAL
J2475_200001
This SAE Recommended Practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include bearing cones, bearing spacers, and wheel hubs. This document is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, R, N, and P. SAE configurations FC, FL, K, L, U, and W are not included, but may be added in the future. The purpose of this document is to establish dimensional guidelines to promote a functional standardization of spindle dimensions wheel end assemblies. Proper hub component dimensions can then be established.
X