Search Results

Fuel injection is a key process influencing the performance of Gasoline Direct Injection (GDI) Engines. Injecting fuel at elevated temperature can initiate flash boiling which can lead to faster breakup, reduced penetration, and increased spray-cone angle. Thus, it impacts engine efficiency in terms of combustion quality, CO2, NOx and soot emission levels. This research deals with modelling of flash boiling processes occurring in gasoline fuel injectors. The flashing mass transfer rate is modelled by the advanced Hertz-Knudsen model considering the deviation from the thermodynamic-equilibrium conditions. The effect of nucleation-site density and its variation with degree of superheat is studied. The model is validated against benchmark test cases and a substantiated comparison with experiment is achieved.

DiMethyl Ether (DME) has been shown to be a very attractive fuel for low emission direct injection compression ignition (DICI) engines. It combines the advantages of the high efficiencies of diesel cycle engines with soot free combustion. However, its greatest drawback is the need to develop new fuel injection and handling systems. Previous approaches have been common rail type injection systems which have shown great potential in reducing harmful exhaust emissions and achieving good engine performance and efficiency due to good control of both the fuel injection characteristics and temperature. The concept also has proven benefits with respect to convenient and safe fuel handling. The logical evolution of this concept simplifies the fuel system and avoids special components for DME handling such as high pressure rail pumps while retaining all the benefits of the common rail principle.

Over the last few years there has been much interest in DiMethyl Ether (DME) as an alternative fuel for diesel cycle engines. It combines the advantages of a high cetane number with soot free combustion, which makes it eminently suitable for compression ignition engines. However, due to the fact that it is a gas under ambient conditions, it requires special fuel handling and a specially designed fuel injection system, which until recently, was not available. The use of the digital hydraulic operating system (DHOS), combined with a fuel handling system designed to cope with the properties of DME, enables the fuel to be safely and conveniently handled, In addition, the flexibility of the injection system enables injection pressures to be chosen according to the needs of the combustion.

Alternative fuels, especially fuels based on biological matter, are gaining more and more attention. Not only as a pure substitute of oil but also in terms of a possibility for further reduction in emission and as an option to improve the global CO2 balance. For improving the engine performance (emissions, fuel consumption, torque and drivability) the adjustment of fuel injection, the fuel evaporation process and the combustion process itself is paramount. In order to exploit the full potential of alternative fuels excellent knowledge of the fuel properties, including the impact on ignition and flame propagation, is required. This needs suitable tools for analysis of the fuel injection and combustion process. These tools have to support the optimization of the combustion system and the dynamic engine calibration for lowest emissions and most efficient use of fuel. As the term “Alternative Fuels” covers a very wide area a brief overview on available fuel types will be made.

A Large-Eddy-Simulation (LES) approach is applied to the calculation of multiple SI-engine cycles in order to study the causes of cycle-to-cycle combustion variations. The single-cylinder research engine adopted in the present study is equipped with direct fuel-injection and variable valve timing for both the intake and exhaust side. Operating conditions representing cases with considerably different scatter of the in-cylinder pressure traces are selected to investigate the causes of the cycle-to-cycle combustion variations. In the simulation the engine is represented by a coupled 1D/3D-CFD model, with the combustion chamber and the intake/exhaust ports modeled in 3D-CFD, and the intake/exhaust pipework set-up adopting a 1D-CFD approach. The adopted LES flow model is based upon the well-established Smagorinsky approach. Simulation of the fuel spray propagation process is based upon the discrete droplet model.

The worldwide trend to increasingly stringent exhaust emissions standards, together with consumer requirements, are forcing both vehicle and engine manufacturers, as well as manufacturers of ancilliary equipment, to introduce new and often novel technology in order to produce clean, quiet and socially acceptable transport at affordable prices. The combustion process lies at the heart of the engine and the quality of the combustion determines the acceptability of the product to a very large extent. The fuel injection system plays a large role in the combustion process and in consequence, the fuel system type and capabilities strongly influence the performance of the combustion system. There has never been such a range of fuel injection systems available at one time as there is today. High pressure hydraulically actuated systems /1/ compete with cam driven fuel injection systems /2/ to deliver the injection requirements demanded by the vehicles both of today and in the future.

A series calculation methodology from the injector nozzle internal flow to the in-cylinder fuel spray and mixture formation in a diesel engine was developed. The present method was applied to a valve covered orifice (VCO) nozzle with the recent common rail injector system. The nozzle internal flow calculation using an Eulerian three-fluid model and a cavitation model was performed. The needle valve movement during the injection period was taken into account in this calculation. Inside the nozzle hole, cavitation appears at the nozzle hole inlet edge, and the cavitation region separates into two regions due to a secondary flow in the cross section, and it is distributed to the nozzle exit. Unsteady change of the secondary flow caused by needle movement affects the cavitation distribution in the nozzle hole, and the spread angle of the velocity vector at the nozzle exit.

A detailed investigation of the influence of intake port design on the in-cylinder flow structure during the intake and compression strokes, the mixing of the residual gas and a non-premixed intake charge, and the extent and pattern of charge inhomogenity near the time of combustion is described. The engine geometry is typical of the current lean-burn design and the study includes comparison of a helical (swirl) port and an idealized direct (no swirl) port designs. The results show marked dependence of the in-cylinder charge mixing characteristics on the intake port design. It is found that combinations of intake port design and manifold fuel injection timing produce favourably-stratified or irregularly-mixed charge distributions at the time of spark ignition. The consequences with respect to combustion characteristics are pointed out.

To meet the future demands on internal combustion engines regarding efficiency emissions and durability all design parameters must be optimized together. As a result of progress in material engineering fuel injection technology turbo charging technology exhaust gas after treatment there arise a multiplicity of possible parameters, such as: design parameters (compression ratio, dimensioning depending on peak firing pressure and mean effective pressure), injection system (rate shaping, split injection, injection pressure, hole diameter), air management (turbo charging with or without VTG, EGR rate) combustion optimization (timing, air access ratio). The interaction of all these parameters can not be over-looked without simulation and optimization tools. This is valid for the concept layout, the optimization and the application process later on.

The subject of this paper is the discussion of a non-dimensional combustion model that relies on the concept of mixing controlled combustion (MCC Heat Release Rate) avoiding the detailed description of the individual mixture formation and fuel oxidation processes. For diffusion combustion in today's direct injection diesel engines it can be shown that the rate of heat release (ROHR) is controlled mainly by two items, i.e. the instantaneous fuel mass present in the cylinder charge and the local density of turbulent kinetic energy. Both items can be derived from the injection process, the instantaneous fuel mass being the difference of fuel injected minus fuel burnt and the turbulent kinetic energy being produced mainly by the momentum of the fuel sprays. Following this strategy, the injection process is now understood as the most important controlling factor for the heat release rate.