Refine Your Search

Topic

Author

Affiliation

Search Results

Video

Future Development of EcoBoost Technology

2012-05-10
Ford's EcoBoost GTDI engine technology (Gasoline Direct Injection, Turbo-charging and Downsizing) is being successfully implemented in the market place with the EcoBoost option accounting for significant volumes in vehicle lines as diverse as the F150 pickup truck, Edge CUV and the Lincoln MKS luxury sedan. A logical question would be what comes after GTDI? This presentation will review some of the technologies that will be required for further improvements in CO2, efficiency and performance building on the EcoBoost foundation as well as some of the challenges inherent in the new technologies and approaches. Presenter Eric W. Curtis, Ford Motor Co.
Technical Paper

The Mvma Investigation Into the Complexities of Heavy Truck Splash and Spray Problem

1985-01-01
856097
Splash and spray conditions created by tractor-trailer combinations operating on the Federal highway system have been studied and tested for many years with mixed results. Past events are reviewed briefly in this paper. In additional testing during 1983, using new state-of- the-art splash/spray suppressant devices, some encouragement was provided that these devices could work. The 1984 Motor Vehicle Manufacturers Association (MVMA) test program was designed to develop practicable and reliable test procedures to measure effectiveness of splash and spray reduction methods applied to tractor-trailer combination vehicles. Over 40 different combinations of splash/spray suppression devices on five different tractors and three van trailer types were tested. The spray-cloud densities for some 400 test runs were measured by laser transmissometers and also recorded by still photography, motion pictures, and videotape. On-site observers made subjective ratings of spray density.
Technical Paper

Inclusion of Crashworthiness in Concept Design

1985-01-01
856090
A side impact study carried out on a particular vehicle has been described and used as a case study to represent a methodology for incorporating side crashworthiness in a new vehicle concept design. In the automotive design environment, it has proved difficult to include side crashworthiness satisfactorily in the initial stages of the passenger car design. Lack of vehicle data at such a stage does not allow detailed finite element analysis. It is, however, possible to suggest the required collapse properties for individual components within the structure so that, through a coarse finite element idealization, a design for crashworthiness can be carried out. The crash properties of the structure can be arrived at by parametric studies of individual components that are absorbing the major portion of the crash energy.
Technical Paper

The Development of Ford's Natural Gas Powered Ranger

1985-11-11
852277
Operation of America's first factory built vehicles modified to operate on natural gas began in April, 1984, when Ford Motor Company delivered the first of 27 specially equipped 1984 Ranger pickup trucks to 25 major utility and natural gas related companies in the United States and Canada. In addition to the fuel system, modifications to these test vehicles include a 12.8:1 compression ratio engine and a unique distributor calibration to provide performance similar to the gasoline powered vehicle. The fuel tanks are significantly more expensive than gasoline tanks and remain one of the major cost issues with a natural gas powered vehicle. There are however, no unresolvable technological issues that would prevent motor vehicles from operating economically and efficiently on natural gas.
Technical Paper

Application of Tuned Mass Damper to Address Discrete Excitation Away From Primary Resonance Frequency of a Structure

2009-05-19
2009-01-2125
Tuned mass dampers (TMDs) or vibration absorbers are widely used in the industry to address various NVH issues, wherein, tactile-vibration or noise mitigation is desired. TMDs can be classified into two categories, namely, tuned-to-resonance and tuned-to-discrete-excitation. An overwhelming majority of TMD applications found in the industry belong to the tuned-to-resonance category, so much of information is available on design considerations of such dampers; however, little is published regarding design considerations of dampers tuned-to-discrete-excitation. During this study, a problem was solved that occurred at a discrete excitation frequency away from the primary resonance frequency of a steering column-wheel assembly. A solution was developed in multiple stages. First the effects of various factors such as mass and damping were analyzed by using a closed-form solution.
Technical Paper

A Method for Torsional Damper Tuning Based On Baseline Frequency Response Functions

2009-05-19
2009-01-2152
Based on Woodbury-Sherman-Morrison formula, a general and efficient method for torsional damper tuning is presented. This method is based on exact calculation of the resulting Frequency Response Functions (FRF's) of the system with the damper by using the original (old) FRF's of the original (baseline) system and the damper's parameters (the mass polar moment of inertia, stiffness and damping coefficient). The only requirement for this method is to have the baseline FRF's at the active points of the structure where the damper is to be attached and those point where the resulting FRF's are of interest. The baseline FRF's can be obtained by either analytical or experimental methods. Once this requirement is met, all possible scenarios of the dampers for their potential and feasibility can be efficiently evaluated before being put into service without the need for costly hardware modification and test cycles on actual structure.
Technical Paper

Low Rhodium Catalyst Technology for Gasoline and FFV Applications

2009-04-20
2009-01-1070
An investigation into the design, development and evaluation of a “new” washcoat technology family that enables significant reductions in rhodium usage levels has been concluded. These findings were demonstrated on three vehicle applications utilizing different calibration A/F control strategies. Additional testing investigated optimal Rh placement on a two brick catalyst system and the impact on FTP and US-06 test cycles. This study concludes with an evaluation of full useful life aged catalysts tested on 6 and 8 cylinder applications that are shown to have met Bin 4 FFV and ULEVII emission standards.
Technical Paper

Finite Element Analyses and Correlations on Oil Canning of a Door Outer Panel

2009-04-20
2009-01-0818
In this paper the nature and analytical methodologies for sheet metal panel oil canning are introduced. Lab tests, numerical predictions using finite element analysis and their correlations on oil canning of a door outer panel are described. Different modeling approaches in finite element analysis are discussed, and a simplified approach of loading by using a coupling element is recommended.
Technical Paper

Correlation of Dominant Noise Transfer Paths in Statistical Energy Analysis Vehicle Model from Test as Basis for Variant Vehicle Development

2013-05-13
2013-01-1994
For purposes of reducing development time, cost and risk, the majority of new vehicles are derived strongly or at least generally from a surrogate vehicle, often of the same general size or body style. Previous test data and lessons learned can be applied as a starting point for design of the new vehicle, especially at early phases of the design before definite design decisions have been finalized and before prototype of production test hardware is available. This is true as well of vehicle NVH development where most new vehicles being developed are variants of existing vehicles for which the main noise transfer paths from sources of interest are already understood via test results and existing targets. The NVH targets for new vehicles are defined via benchmarking, market considerations, and other higher-level decisions. The objective is then to bridge the gap between test data from surrogate vehicles to direct support of the NVH development of new vehicle programs.
Technical Paper

Optimization of New Plastic Bracket NVH Characteristics using CAE

2012-10-02
2012-36-0195
NVH requirements are critical in new driveline developments. Failure modes due to resonances must be carefully analyzed and potential root causes must have adequate countermeasures. One of the most common root causes is the modal alignment. This work shows the steps to design and optimize a new plastic bracket for an automotive half shaft bearing. This bracket replaces a very stiff bracket, made of cast iron. The initial design of plastic bracket was not stiff enough to bring natural frequency of the system above engine second order excitation at maximum speed. The complete power pack was modeled and NVH CAE analysis was performed. The CAE outputs included Driving Point Response, Frequency Response Function and Modal analysis. The boundary conditions were discussed deep in detail to make sure the models represented actual system.
Technical Paper

Methodology for Developing and Validating Air Brake Tubes for Commercial Vehicles

2012-10-02
2012-36-0272
The pneumatic air brake system for heavy commercial trucks is composed by a large number of components, aiming its proper work and compliance with rigorous criteria of vehicular safety. One of those components, present along the whole vehicle, is the air brake tube, ducts which feed valves and reservoirs with compressed air, carrying signals for acting or releasing the brake system. In 2011, due to a lack of butadiene in a global scale, the manufacturing of these tubes was compromised; as this is an important raw material present on the polymer used so far, PA12. This article introduces the methodology of selecting, developing and validating in vehicle an alternative polymer for this application. For this purpose, acceptance criteria have been established through global material specifications, as well as bench tests and vehicular validation requirements.
Technical Paper

Development of a Tunable Stamped Collector to Improve Exhaust System Performance

1994-11-01
942271
A tunable stamped collector was developed to improve vehicle performance, drive-by noise and subjective noise quality, and reduced thermal stress concentrations. The stamped collector is located at the junction of the legs of the down pipe/catalytic converter assembly for a transverse mounted V-6 engine and acts to equalize the leg length of the down pipe, as well as provide acoustic tuning volume. This collector differs from most other methods to equalize leg lengths on transverse mounted engines in that it has a tuning chamber incorporated into the design itself, which allows for specific noise frequencies to be reduced. Performance characteristics were measured for a conventional down-pipe and the stamped collector using the following analysis techniques: Frequency analysis of tailpipe noise emissions. Drive-by noise emissions. Horsepower measurements using an engine dynamometer.
Technical Paper

A General Formulation for Topology Optimization

1994-11-01
942256
Topology optimization is used for obtaining the best layout of vehicle structural components to achieve predetermined performance goals. Unlike the most common approach which uses the optimality criteria methods, the topology design problem is formulated as a general optimization problem and is solved by the mathematical programming method. One of the major advantages of this approach is its generality; thus it can solve various problems, e.g. multi-objective and multi-constraint problems. The MSC/NASTRAN finite element code is employed for response analyses. Two automotive examples including a simplified truck frame and a truck frame crossmember are presented.
Technical Paper

Diesel Fuel Delivery Module for Light Truck Applications

1993-11-01
932980
This paper reviews the design and development of a self-filling, in-tank fuel system reservoir intended for use in diesel engine vehicle applications. This new idea eliminates engine driveability concerns (stumbles, hesitations, stalling, etc.) associated with an inconsistent supply of fuel from the fuel tank to the engine, particularly during sudden vehicle maneuvers and with low fuel tank conditions.
Technical Paper

Impact of Computer Aided Engineering on Ford Motor Company Light Truck Cooling Design and Development Processes

1993-11-01
932977
This paper presents the benefits of following a disciplined thermal management process during the design and development of Ford Light Truck engine cooling systems. The thermal management process described has evolved through the increased use of Computer Aided Engineering (CAE) tools. The primary CAE tool used is a numerical simulation technique within the field of Computational Fluid Dynamics (CFD). The paper discusses the need to establish a heat management team, develop a heat management model, construct a three dimensional CFD model to simulate the thermal environment of the engine cooling system, and presents CFD modeling examples of Ford Light Trucks with engine driven cooling fans.
Technical Paper

Ranking of Lubricants for Flexible Fuel Vehicles (FFV) by a Short Engine Sequence Test

1993-10-01
932790
A short engine sequence test, based on the Sequence VD procedure, was used to screen FFV oil candidates more rapidly. Since only one engine is needed to compare the wear-protection performance of several lubricants, engine hardware variability is not a significant issue in this test procedure. Several lubricants, some specially formulated for FFV engines, were tested using standard Sequence VD engine hardware which includes molybdenum top piston-rings. Results showed clear discrimination of the performance of oil candidates. These lubricants were also tested using an engine with chromium-faced top rings and exhibited similar performance ranking.
Technical Paper

Effect of Engine Operating Parameters on Hydrocarbon Oxidation in the Exhaust Port and Runner of a Spark-Ignited Engine

1995-02-01
950159
The effect of engine operating parameters (speed, spark timing, and fuel-air equivalence ratio [Φ]) on hydrocarbon (HC) oxidation within the cylinder and exhaust system is examined using propane or isooctane fuel. Quench gas (CO2) is introduced at two locations in the exhaust system (exhaust valve or port exit) to stop the oxidation process. Increasing the speed from 1500 to 2500 RPM at MBT spark timing decreases the total, cylinder-exit HC emissions by ∼50% while oxidation in the exhaust system remains at 40% for both fuels. For propane fuel at 1500 rpm, increasing Φ from 0.9 (fuel lean) to 1.1 (fuel rich) reduces oxidation in the exhaust system from 42% to 26%; at 2500 RPM, exhaust system oxidation decreases from 40% to approximately 0% for Φ = 0.9 and 1.1, respectively. Retarded spark increases oxidation in the cylinder and exhaust system for both fuels. Decreases in total HC emissions are accompanied by increased olefinic content and atmospheric reactivity.
Technical Paper

Determination of Dimensional Changes in Injection Molded Bosses Using Strain Gages: Effects on Joint Durability

1994-03-01
940653
Improvements in clamp load retention of fastened joints in instrument panels are desired by automotive OEMs to minimize warranty claims due to squeak and rattle problems. The decrease in torque retention of these plastic boss and metal fastener joints over time and temperature cycling was described in a previous SAE technical paper.1 This loss in clamp load retention (which is another measure of joint durability), as measured by torque, was shown to be affected by differences in the thermal expansion rates of the captured materials. The purpose of this paper is to further quantify these differences by using strain gages to measure the thermal expansion rates and dimensional changes of the joint's various components: metal fastener, molded plastic boss, and captured material.
Technical Paper

A New Approach for Weight Reduction in Truck Frame Design

1993-11-01
933037
A new, systematic, sensitivity based design process for weight reduction is presented. Traditionally, a trial and error method is used when a design fails to meet the weight and the design criteria, which often conflict. This old approach not only is time and cost consuming but also does not provide insight into structural behavior. This proposed process uses state-of-the-art technologies such as design sensitivity analysis, numerical optimization, graphical user interface, etc. It handles multi-discipline design criteria simultaneously and provides design engineers insight into structural responses for frequency, durability, and stiffness concerns and a means for systematic weight reduction and quality improvement. The new design process has been applied for the weight reduction of advanced truck frame designs. Results show that a significant weight savings has been achieved while all design criteria are met.
X