Search Results

Real-time simulation of truck and trailer combinations can be applied to hardware-in-the-loop (HIL) systems for developing and testing electronic control units (ECUs). The large number of configuration variations in vehicle and axle types requires the simulation model to be adjustable in a wide range. This paper presents a modular multibody approach for the vehicle dynamics simulation of single track configurations and truck-and-trailer combinations. The equations of motion are expressed by a new formula which is a combination of Jourdain's principle and the articulated body algorithm. With the proposed algorithm, a robust model is achieved that is numerically stable even at handling limits. Moreover, the presented approach is suitable for modular modeling and has been successfully implemented as a basis for various system definitions. As a result, only one simulation model is needed for a large variety of track and trailer types.

Due to the diversity of Heavy Duty Vehicles (HDV), the European CO2 and fuel consumption monitoring methodology for HDVs will be based on a combination of component testing and vehicle simulation. In this context, one of the key input parameters that need to be accurately defined for achieving a representative and accurate fuel consumption simulation is the vehicle's aerodynamic drag. A highly repeatable, accurate and sensitive measurement methodology was needed, in order to capture small differences in the aerodynamic characteristics of different vehicle bodies. A measurement methodology is proposed which is based on constant speed measurements on a test track, the use of torque measurement systems and wind speed measurement. In order to support the development and evaluation of the proposed approach, a series of experiments were conducted on 2 different trucks, a Daimler 40 ton truck with a semi-trailer and a DAF 18 ton rigid truck.

The spray-guided combustion process offers a high potential for fuel savings in gasoline engines in the part load range. In this connection, the injector and spark plug are arranged in close proximity to one another, as a result of which mixture formation is primarily shaped by the dynamics of the fuel spray. The mixture formation time is very short, so that at the time of ignition the velocity of flow is high and the fuel is still largely present in liquid form. The quality of mixture formation thus constitutes a key aspect of reliable ignition. In this article, the spray characteristics of an outward-opening piezo injector are examined using optical testing methods under pressure chamber conditions and the results obtained are correlated with ignition behaviour in-engine. The global spray formation is examined using high-speed visualisation methods, particularly with regard to cyclical fluctuations.

In the aerospace industry, methods for virtual testing cover an increasing range of test executions carried out during the development and test process of avionics systems. Over the last years, most companies have focused on questions regarding the evaluation and implementation of methods for virtual testing. However, it has become more and more important to seamlessly integrate virtual testing into the overall development process. For instance, a company’s test strategy might stipulate a combination of different methods, such as SIL and HIL simulation, in order to benefit from the advantages of both in the same test process. In this case, efforts concentrate on the optimization of the overall process, from test specification to test execution, as well as the test result evaluation and its alignment with methods for virtual testing.

Real-time simulation of truck and trailer combinations can be applied to hardware-in-the-loop (HIL) systems for developing and testing electronic control units (ECUs). The large number of configuration variations in vehicle and axle types requires the simulation model to be adjustable in a wide range. This paper presents a modular multibody approach for the vehicle dynamics simulation of single track configurations and truck-and-trailer combinations. The equations of motion are expressed by a new formula which is a combination of Jourdain's principle and the articulated body algorithm. With the proposed algorithm, a robust model is achieved that is numerically stable even at handling limits. Moreover, the presented approach is suitable for modular modeling and has been successfully implemented as a basis for various system definitions. As a result, only one simulation model is needed for a large variety of track and trailer types.

Aerodynamic design and thermal management are some of the most important tasks when developing new concepts for the flow around tractor-trailers. Today, both experimental and numerical studies are an integral part of the aerodynamic and thermal design processes. A variety of studies have been conducted how the aerodynamic design reduces the drag coefficient for fuel efficiency as well as for the construction of radiators to provide cooling on tractor-trailers. However, only a few studies cover the combined effect of the aerodynamic and thermal design on the air temperature of the under hood flow [8, 13, 16, 17, 20]. The objective of this study is to analyze the heat transfer through forced convection for a scaled Cab-over-Engine (CoE) tractor-trailer model with under hood flow. Different design concepts are compared to provide low under hood air temperature and efficient cooling of the sub components.

Hardware-in-the-loop (HIL) simulation in the development and test process of vehicle dynamics controllers requires a real-time tractor-trailer simulation model. The hitch coupling must be numerically stable to ensure real-time simulation for various driving maneuvers, particularly at the vehicle's handling limits. This paper presents a robust implementation of tractor-trailer coupling. The equation of motion is formed using a novel formulation which is a combination of Jourdain's Principle and the Articulated Body Algorithm. The paper shows that a robust model for a real-time tractor-trailer simulation can be achieved with the proposed method. Moreover, the approach presented is suitable for modular modeling, is successfully implemented and can also be used as a basis for flexible system definition with an adjustable number of trailer axles.

Brake system development and testing is spread over vehicle manufacturers, system and component suppliers. Test equipment from different sources, even resulting from different technology generations, different data analysis and report tools - comprising different and sometimes undocumented algorithms - lead to a difficult exchange and analysis of test results and, at the same time, contributes to unwanted test variability. Other studies regarding the test variability brought up that only a unified and unambiguous data format will allow a meaningful and comparative evaluation of these data and only standardization will reveal the actual reasons of test variability. The text at hand illustrates that a substantial part of test variability is caused by a misinterpretation of data and/or by the application of different algorithms.

Increasing diagnosis capabilities in modern engine electronic control units (ECUs), especially in the exhaust path, in terms of emission and engine aftertreatment control utilize on-board NOx prediction models. Nowadays it is an established approach at hardware-in-theloop (HIL) test benches to replicate the engine's steady-state NOx emissions on the basis of stationary engine data. However, this method might be unsuitable for internal ECU plausibility checks and ECU test conditions based on dynamic engine operations. Examples of proven methods for modeling the engine behavior in HIL system applications are so-called mean value engine models (MVEMs) and crank-angle-synchronous (in-cylinder) models. Of these two, only the in-cylinder model replicates the engine’s inner combustion process at each time step and can therefore be used for chemical-based emission simulation, because the formation of the relevant gas species is caused by the inner combustion states.

Hybrid test systems are gaining more and more significance in the aerospace industry. At the heart of these systems is a standardized communication infrastructure. There are many challenges when designing the communication infrastructure. For example, it requires very specific knowledge to boot a hybrid system, manage its configuration process, and start and stop the execution of applications, such as simulations, panels or recorders. Likewise, when testers use a heterogeneous test environment, they cannot commit themselves too much to every single test means and its special characteristics. Nevertheless, testers must always be able to monitor and control every test system. This means, they must be able to determine the current overall system status and the current status of its components and parts. Examples for this are hardware components, such as real-time processors and I/O boards, as well as software applications, such as real-time simulations models on the test system.

The increasing shift of drive operation towards efficient engine operation points at very low engine speeds demands a concerted design and tuning of engine, drive-train, assembly attachment and body to avoid annoying low speed boom noise. An additional challenge in this area of conflict is the increasing torque of modern engines at low engine speeds. As an example for a standard passenger car, the modes of operation, which may lead to low speed boom noise, are described. Setting levers along the complete chain of effect are characterised - from cylinder pressure up to the radiating surfaces of the interior. To achieve challenging NVH-targets the application of nonlinear simulation systems is indispensable, in particular in the concept phase of a vehicle. The use of multi-body simulation is presented for a concentrated NVH-optimisation of powertrain and rear axle vibration behaviour to reduce low-speed boom noise. On entire vehicle level hybrid simulation models are useful.

Downsizing and direct injection in modern DISI engines can lead to fuel impinging on the cylinder walls. The interaction of liquid fuel and engine oil due to fuel impinging on the cylinder wall causes problems in both lubrication and combustion. To analyze this issue with temporal and spatial resolution, we developed a laser-induced fluorescence (LIF) system for simultaneous kHz-rate imaging of fuel and oil films on the cylinder wall. Engine oil was doped with traces of the laser dye pyrromethene 567, which fluoresces red after excitation by 532 nm laser radiation. Simultaneously, the liquid fuel was visualized by UV fluorescence of an aromatic “tracer” in a non-fluorescent surrogate fuel excited at 266 nm. Two combinations of fuel and tracer were investigated, iso-octane and toluene as well as a multi-component surrogate and anisole. The fluorescence from oil and fuel was spectrally separated and detected by two cameras.

The importance of electronics, especially software, has greatly increased over the last few years. Efforts to maintain a high level of software quality have made testing an important part of the development process. With the advent of model-based development, testing methods can be used not only on code level, but also on model level. Next to test execution itself, test development is seen as the most time- and cost-intensive part of the testing process. This paper outlines and classifies current approaches to model-based test development, with the aim of providing guidelines for test developers for choosing the method best suited to the type of system under test and the test objective.

In the digital prototype development process of a new Mercedes-Benz, thermal protection is an important task that has to be fulfilled. In the early stages of development, numerical methods are used to detect thermal hotspots in order to protect temperature sensitive parts. These methods involve transient full Vehicle Thermal Management (VTM) simulations to predict dynamic vehicle heat-up during critical load cases. In order to simulate thermal control mechanisms, a coupled 1D to 3D thermal vehicle model is built in which the coolant and oil circuit of the engine, as well as the exhaust flow are captured in detail. When performing a transient 3D VTM analysis, the conduction and radiation phenomena are simulated using a transient structure model while the convective phenomena are co-simulated in a steady state fluid model. Both models are brought to interaction at predetermined points by an automatized coupling method.

Not only is the number of electronic control units (ECUs) in modern vehicles constantly increasing, the software of the ECUs is also becoming more complex. Both make testing a central task within the development of automotive electronics. Testing ECUs in real vehicles is time-consuming and costly, and comes very late in the automotive development process. It is therefore increasingly being replaced by laboratory tests using hardware-in-the-loop (HIL) simulation. While new software functions are still being developed or optimized, other functions are already undergoing certain tests, mostly on module level but also on system and integration level. To achieve the highest quality, testing must be done as early as possible within the development process. This paper describes the various test phases during the development of automotive electronics (from single function testing to network testing of all the ECUs of a vehicle).

This paper describes a new production code generator that meets both the requirements of code developers for efficient and reliable production code, as well as the desire of system engineers to establish a control design process based on simulation models that double as executable specifications for the ECU software. The production code generator supports automatic scaling, generates optimized fixed-point C code for microcontrollers like the Motorola 683xx, Siemens C16x, and Hitachi SH-2, and produces ASAP2 [1] calibration information. Benchmark results show that the autogenerated code can match or even exceed the efficiency of typical handwritten production code. Code quality is assured by design and by systematic, automatic, and extremely comprehensive test procedures.

This paper presents a demonstrator developed in the European CleanSky2 project MISSION (Modelling and Simulation Tools for Systems Integration on Aircraft). Its scope is the development towards a seamless integrated, interconnected toolchain enabling more efficient processes with less rework time in todays, highly collaborative aerospace domain design applications. The demonstration described here, consists of an open, modular and multitool platform implementation, using specific techniques to achieve fully traceable (early stage) requirements verification by virtual testing. The most promising approach is a model based integration along the whole process from requirements definition to the verified, integrated (and certified) system. Extending previous publications in this series, the paper introduces the motivation and briefly describes the technical background and a potential implementation of a workflow suitable for that target.

In the next 20 years the share of small electric vehicles (SEVs) will increase especially in urban areas. SEVs show distinctive design differences compared to traditional vehicles. Thus the consequences of impacts of SEVs with vulnerable road users (VRUs) and other vehicles will be different from traditional collisions. No assessment concerning vehicle safety is defined for vehicles within European L7e category currently. Focus of the elaborated methodology is to define appropriate test scenarios for this vehicle category to be used within a virtual tool chain. A virtual tool chain has to be defined for the realization of a guideline of virtual certification. The derivation and development of new test conditions for SEVs are described and are the main focus of this work. As key methodology a prospective methodical analysis under consideration of future aspects like pre-crash safety systems is applied.

In this paper a new numerical methodology to compute component temperatures of a rotating cardan shaft is described. In general temperatures of the cardan shaft are mainly dominated by radiation from the exhaust gas system and air temperatures in the transmission tunnel and underbody. While driving the cardan shaft is rotating. This yields a uniform temperature distribution of the circumference of the shaft. However most simulation approaches for heat protection are nowadays steady-state computations. In these simulations the rotation of the cardan shaft is not considered. In particular next to the exhaust gas system the distribution of the temperatures of the cardan shaft is not uniform but shows hot temperatures due to radiation at the side facing the exhaust gas system and lower temperatures at the other side. This paper describes a new computational approach that is averaging the radiative and convective heat fluxes circumferentially over bands of the cardan shaft.

Hardware-in-the-loop (HIL) simulation is now a standard component in the vehicle development process as a method for testing electronic control unit (ECU) software. HIL simulation is used for all aspects of development, naturally including safety-relevant functions and systems. This applies to all test tasks (from function testing to release tests, testing a single ECU or an ECU network, and so on) and also to different vehicle domains: The drivetrain, vehicle dynamics, driver assistance systems, interior/comfort systems and infotainment are all tested by HIL simulation. At the same time, modern vehicles feature more and more safety-related systems such as Adaptive Cruise Control, Electronic Stability Program, Power Assisted Steering, and Integrated Chassis Management.