Search Results

The development of a leanburn engine is described, in which optimized engine design, innovative engine management and exhaust gas aftertreatment using a special NOx-storage catalyst were combined to yield a significant improvement in fuel economy with reduced NOx emissions. To achieve stable combustion near the lean limit a swirl system was used and the appropriate parameters of the 2.2 I 4-cyIinder 4-valve SI engine were optimized. As a result, the mixture formation was improved and the lean limit was extended to higher air-fuel ratios. An adaptive lambda controller which was based on the evaluation of engine-smoothness calculated from the RPM-sensor was implemented to control each cylinder individually close to the lean limit. A model-based control system was developed to achieve extremely accurate air-fuel ratio control during transients.

For meeting 21st-century exhaust emission standards for HD diesel engines, new methods are necessary for reducing NOx and PM emissions without increasing fuel consumption. The stratified diesel fuel-water-diesel fuel (DWD) injection in combination with exhaust gas recirculation (EGR) is as a means for NOx and PM reduction without any negative effect on fuel economy. The investigation was performed on a charged HD single-cylinder direct-injection diesel engine with a modern low-swirl combustion system, 4-valve technology and high pressure injection. The application of DWD injection combined with EGR resulted in a 60 percent lower NOx emission at full load and a 75 percent reduced NOx emission at part load when compared with present day (EURO II) technology. This was achieved without any fuel economy penalty, but with an additional PM emission reduction.

An adsorber system for reducing cold start hydrocarbon (HC) emissions has been developed combining existing catalyst technologies with a zeolite-based HC adsorber. The series flow in-line concept offers a passive and simplified alternative to other technologies by incorporating one additional adsorber substrate into existing converters without any additional valving, purging lines, or special substrates. This contribution describes the current development status of hydrocarbon adsorber aftertreatment technologies. We report results obtained with a variety of adsorber, start-up, and underfloor catalyst system combinations. In each case, it was possible to achieve HC emission levels in compliance with the ULEV standards, and in the best cases, demonstrating HC emissions substantially below the legislated standard.

A common rail injection system was applied to port-loop and uniflow scavenged two-stroke DI-Diesel engines. While the uniflow scavenged configuration was operated with a swirl level comparable to that of 4-stroke DI-Diesel engines, no swirl motion was realized with the port-loop scavenged arrangement. The results show that, in spite of disadvantages in the mixture formation process, the high mixture formation energy observed with the common rail injection makes a swirl-free Diesel combustion possible. However, at part load the combustion process and emission level with the port-loop scavenged engine is not satisfactory. At full load, disadvantages in the scavenging process are observed in addition to the poorer mixture formation with the loop scavenged two-stroke concept. Consequently, the expected specific power output of the port-loop scavenged arrangement is with 20 kW/l far lower than about 45 kW/l predicted for the uniflow scavenged engine.

Introduction of an array of new electrical and electronic features into future vehicles is generating vehicle electrical power requirements that exceed the capabilities of today's 14 volt electrical systems. In the near term (5 to 10 years), the existing 14V system will be marginally capable of supporting the expected additional loads with escalating costs for the associated charging system. However, significant increases in vehicle functional content are expected as future requirements to meet longer-term (beyond 10 years) needs in the areas of emission control, fuel economy, safety, and passenger comfort. A higher voltage electrical system will be required to meet these future requirements. This paper explores the functional needs that will mandate a higher voltage system and the benefits derivable from its implementation.

The SNR-technique is a new NOx aftertreatment system for lean burn gasoline and diesel applications. The objective of SNR is NOx removal from lean exhaust gas by NOx adsorption and subsequent selective external recirculation and decomposition of NOx in the combustion process. The SNR-project is composed of two major parts. Firstly the development of NOx adsorbents which are able to store large quantities of NOx in lean exhaust gas, and secondly the NOx decomposition by the combustion process. Emphasis of this paper is the investigation of NOx reduction in the combustion process, including experimental investigation and numerical simulation. The NOx decomposition process has been proven in diesel and lean-burn gasoline engines. Depending on the type of engine NOx-conversion rates up to 90 % have been observed. Regarding the complete SNR-system, including the efficiency of the adsorbing material and the NOx decomposition by the combustion, a NOx removal of more than 50% is achievable.

Selective NOx recirculation (SNR), involving adsorption, selective external recirculation and decomposition of the NOx by the combustion process, is itself a promising technique to abate NOx emissions. Three types of materials containing Ba: barium aluminate, barium tin perovskite and barium Y-zeolites have been developed to adsorb NOx under lean-burn or Diesel conditions, with or without the presence of S02. All these materials adsorb NO2 selectively (lean-burn conditions), and store it as nitrate/nitrite species. The desorption takes place by decomposition of these species at higher temperatures. Nitrate formation implies also sulfate formation in the presence of SO2 and SO3, while the NO2/SO2 competition governs the poisoning of such catalysts.

The combustion process of a heavy-duty DI-Diesel truck engine has been investigated using numerical simulation. The numerical modeling was based on an improved version of the KIVA-2 engine simulation code, employing a modified characteristic time-scale combustion model and a modified Kelvin-Helmholtz spray atomization model. The NO-formation process was modeled using the extended thermal Zeldovich mechanism. The simulation efforts included the effects of different injection characteristics such as varying the injection rate profile or number of injection holes and sizes. The physical sub-models used to improve the simulation of the mixture-formation and the combustion process were validated through comparison with single-cylinder engine experiments. Special attention was given to accurately model the in-cylinder flame propagation of the individual sprays and their effect on thermal NO-formation. All simulations were based on full load cases at medium speed.

In his paper “The Knock Syndrome - its Cures and its Victims” (SAE 841339) Oppenheim proposed to change the whole process of the internal combustion engine replacing moving flames by homogeneous and simultaneous combustion. Intensive research work on flame propagation and auto-ignition phenomena led to new insights into combustion over recent years. The implementation of auto-ignition on two-stroke S.I. engines revealed the potential for simultaneous reductions in fuel consumption and NOx emission. Deploying the principle for the four-stroke piston engine and standard fuel would provide optimum conditions for application in common vehicles. The basic problem of homogeneous combustion is presented and some options of control are discussed. A methodology is proposed to apply a new type of combustion simply through a consistent combination of modern technology available for the S.I. engine.

Chemiluminescence imaging has been applied to a parametric investigation of diesel autoignition. Time-resolved images of the natural light emission were made in an optically accessible DI diesel engine of the heavy-duty size class using an intensified CCD video camera. Measurements were obtained at a base operating condition, corresponding to a motored TDC temperature and density of 992 K and 16.6 kg/m3, and for TDC temperatures and densities above and below these values. Data were taken with a 42.5 cetane number blend of the diesel reference fuels for all conditions, and measurements were also made with no. 2 diesel fuel (D2) at the base condition. For each condition, temporal sequences of images were acquired from the time of first detectable chemiluminescence up through fully sooting combustion, and the images were analyzed to obtain quantitative measurements of the average emission intensity.

In the past there has been a concentration on performing LCAs of car components. Based on the increasing experience and know-how gained in the past by performing LCAs of car components truck designers get the chance to make a statement about the ecological impact of each alternative. The most significant difference between LCAs of car and truck components is the use phase. This paper describes a Life-Cycle-Assessment (LCA) of different air deflection systems made of composite materials. The actually used system is produced by Resin Transfer Molding (RTM) while a possible alternative could be made out of Sheet Molding Compound (SMC). The calculations have shown that there exists a potential to improve the ecological profiles of composite components by replacing glass fibers with natural fibers.

The awareness concerning environmental issues and the economical need for fuel savings leads to the introduction of new, highly efficient Diesel engines for passenger cars. An engine with common rail injection system could meet this target and, with the help of an advanced diesel exhaust aftertreatment system also fulfilled the new legislative emission regulations. Besides the efficient oxidation of carbon monoxide (CO), hydrocarbons (HC) and diesel particulates, such a system also requires a moderate reduction efficiency for nitrogen oxides (NOx) under excess oxygen conditions. The present paper illustrates the further progress in catalytic NOx-reduction under excess of oxygen by hydrocarbon enrichment using the common rail injection system.

The present paper describes the results of a joint development program focussing on a system approach to meet the proposed EURO III and IV emission standards for a passenger car equipped with a 3.2 liter, 18 valve gasoline engine. Starting with the in-production configuration of a EURO II certified vehicle (model year 1997) the following improvement points were investigated in detail. By the introduction of a close-coupled catalyst in combination with engine measures to improve the catalyst light-off the proposed EURO III limits were met. The proposed EURO IV hurdle could be overcome by further using secondary air injection during cold-start in combination with an increased precious metal loading for the close-coupled catalyst.

The Series Hybrid project is described concerning the scenario, technical data of vehicle and components and operating strategy. The two prototype cars offer an attractive driveability. Test results show high potential on emission reduction without increasing the consumption. The question is frequently asked as to which concept is the best. It is not so easy to answer this question. It can only mean: which concept is the best for a given application? In our opinion parallel hybrids make sense where a vehicle is required to be driven both conventionally and with electric drive only, e.g. conurbation scenario, driving and delivering in sensitive areas. In terms of weight, packaging and costs, a realization is much easier if electric-only propulsion is only required for a limited performance and range.

The effect of fuel additives based on the alkali metals sodium and lithium on the regeneration behaviour of diesel particulate filters was studied. For this purpose the diesel fuel was doped with the lithium and sodium salts of an aliphatic alcohol. The efficiency of these additives was assessed by comparing it to ferrocene, which is, at present, the best studied additive for particulate filter regeneration. The additives were tested on an engine test bench under steady state conditions, on a transient dynamometer and finally in a real driving test. As a result of the addition of the alkali metal salts, the ignition temperature of the soot trapped in the particulate filter is considerably lower than the ignition temperature without additives. The results with the alkali metal additives are similar to those of ferrocene or other additives with transition metals like manganese or copper.

Realization of the leanburn SI engine's potential for improved fuel economy strongly depends on precise control of the air-fuel ratio (AFR), especially during transients, for acceptable driveability and low exhaust emissions. The development of an adaptive-feedforward model-based AFR controller is described. A discrete, nonlinear, control-oriented engine model was developed and used in the AFR control algorithm. The engine model includes intake-manifold airflow dynamics, fuel wall-wetting dynamics, process delays inherent in the four-stroke engine cycle, and exhaust-gas oxygen (UEGO) sensor dynamics. The sampling period is synchronous with crank-angle (“event-based”) for more precise control. The controller relies on the engine speed and throttle position for load information. An intake-manifold pressure (MAP) sensor is used for identification of the airflow dynamics, but not for control. The MAP sensor would also be useful for the cold start and for engine diagnostics.

The importance of autonomous vehicle operation to satisfy future safety and productivity requirements is emphasized by the current National plans for IVHS and AHS development and deployment. Daimler-Benz Research, in cooperation with Freightliner Corporation, is developing a research vehicle VECTOR (Vision Enhanced/Controlled Truck for Operational Research) which currently is undergoing testing of a vision-based control system for lateral guidance. This effort is building on experience from prior Daimler-Benz and PROMETHEUS projects, including the test vehicles VITA (VIsion Technology Application) and OSCAR (Optically Steered CAR). The paper describes this work and future expansion plans to incorporate longitudinal control systems in VECTOR.

One possibility to improve the fuel economy of SI-engines is to run the engine with a lean air-fuel-ratio (AFR). Hydrocarbon and carbon monoxide after-treatment has been proven under lean operation, but NOx-control remains a challenge to catalyst and car manufacturers. One strategy that is being considered is to run the engine lean with occasional operation at stoichiometry. This would be in conjunction with a three-way-catalyst (TWC) to achieve stoichiometric conversion of the three main pollutants in the normal way and a NOx trap. The NOx trap stores NOx under lean operation to be released and reduced under rich conditions. The trap also functions as a TWC and has good HC and CO conversion at both lean and stoichiometric AFR's. Under lean conditions NO is oxidised to NO2 on Pt which is then adsorbed on an oxide surface. Typical adsorbent materials include oxides of potassium, calcium, zirconium, strontium, lanthanum, cerium and barium.

The use of pistons made of fine grain carbon was investigated in a spark-ignition engine within a European Community funded research project (TPRO-CT92-0008). Pistons were designed and manufactured and then tested in a single cylinder engine. Due to the carbon material's lower coefficient of thermal expansion the top land clearance between piston and cylinder can be reduced by a factor of three in comparison to standard aluminium designs. Under steady-state part-load operating conditions the emission of unburned hydrocarbons can be reduced by more than 15% compared to aluminium pistons, without significant penalties in NOx-emissions. Simultaneously, a small improvement in fuel economy of about 2% is observed. At full-load blow-by leakage flow is reduced by more than 50%. The piston crown temperature is about 30°C higher with the carbon piston than with the standard aluminium piston, due to the lower thermal conductivity of the carbon material.

The two major problems of diesel emission control are the reduction of nitrogen oxides and particulates. This paper describes experimental investigations to achieve both a separation of soot particles as well as a catalytic NOx reduction with hydrocarbons under lean diesel exhaust gas conditions. For that purpose a diesel particle trap is coated with a catalyst based on a Pt containing zeolite. Preliminary studies have been performed on the catalytic NOx reduction to evaluate the efficiency of a Pt/zeolite system as well as to establish the impact of operation conditions on the catalyst performance. The activity of the prepared samples (catalytic coating on particle trap) has been determined under model gas test conditions. Much attention has been focussed on the steady-state kinetics of the surface processes. Another aspect considered is the N2O formation which can be reduced, when alkali-earth or rare-earth oxides are added to the catalyst system.