Search Results

The development of a leanburn engine is described, in which optimized engine design, innovative engine management and exhaust gas aftertreatment using a special NOx-storage catalyst were combined to yield a significant improvement in fuel economy with reduced NOx emissions. To achieve stable combustion near the lean limit a swirl system was used and the appropriate parameters of the 2.2 I 4-cyIinder 4-valve SI engine were optimized. As a result, the mixture formation was improved and the lean limit was extended to higher air-fuel ratios. An adaptive lambda controller which was based on the evaluation of engine-smoothness calculated from the RPM-sensor was implemented to control each cylinder individually close to the lean limit. A model-based control system was developed to achieve extremely accurate air-fuel ratio control during transients.

For meeting 21st-century exhaust emission standards for HD diesel engines, new methods are necessary for reducing NOx and PM emissions without increasing fuel consumption. The stratified diesel fuel-water-diesel fuel (DWD) injection in combination with exhaust gas recirculation (EGR) is as a means for NOx and PM reduction without any negative effect on fuel economy. The investigation was performed on a charged HD single-cylinder direct-injection diesel engine with a modern low-swirl combustion system, 4-valve technology and high pressure injection. The application of DWD injection combined with EGR resulted in a 60 percent lower NOx emission at full load and a 75 percent reduced NOx emission at part load when compared with present day (EURO II) technology. This was achieved without any fuel economy penalty, but with an additional PM emission reduction.

A common rail injection system was applied to port-loop and uniflow scavenged two-stroke DI-Diesel engines. While the uniflow scavenged configuration was operated with a swirl level comparable to that of 4-stroke DI-Diesel engines, no swirl motion was realized with the port-loop scavenged arrangement. The results show that, in spite of disadvantages in the mixture formation process, the high mixture formation energy observed with the common rail injection makes a swirl-free Diesel combustion possible. However, at part load the combustion process and emission level with the port-loop scavenged engine is not satisfactory. At full load, disadvantages in the scavenging process are observed in addition to the poorer mixture formation with the loop scavenged two-stroke concept. Consequently, the expected specific power output of the port-loop scavenged arrangement is with 20 kW/l far lower than about 45 kW/l predicted for the uniflow scavenged engine.

In conjunction with throttle-free load control on a 4-valve, single-cylinder spark-ignition engine, the influencing variables of charge cycle, mixture formation and combustion process are presented both as computer calculations and on the basis of test results. The influences of the position of the maximum of the inlet valve stroke, the position of the inlet close, the shape of the valve stroke and the load motion in relation to the maximum power and minimum fuel consumption are investigated in full load by computer calculations and in partial load by engine tests.

Introduction of an array of new electrical and electronic features into future vehicles is generating vehicle electrical power requirements that exceed the capabilities of today's 14 volt electrical systems. In the near term (5 to 10 years), the existing 14V system will be marginally capable of supporting the expected additional loads with escalating costs for the associated charging system. However, significant increases in vehicle functional content are expected as future requirements to meet longer-term (beyond 10 years) needs in the areas of emission control, fuel economy, safety, and passenger comfort. A higher voltage electrical system will be required to meet these future requirements. This paper explores the functional needs that will mandate a higher voltage system and the benefits derivable from its implementation.

The SNR-technique is a new NOx aftertreatment system for lean burn gasoline and diesel applications. The objective of SNR is NOx removal from lean exhaust gas by NOx adsorption and subsequent selective external recirculation and decomposition of NOx in the combustion process. The SNR-project is composed of two major parts. Firstly the development of NOx adsorbents which are able to store large quantities of NOx in lean exhaust gas, and secondly the NOx decomposition by the combustion process. Emphasis of this paper is the investigation of NOx reduction in the combustion process, including experimental investigation and numerical simulation. The NOx decomposition process has been proven in diesel and lean-burn gasoline engines. Depending on the type of engine NOx-conversion rates up to 90 % have been observed. Regarding the complete SNR-system, including the efficiency of the adsorbing material and the NOx decomposition by the combustion, a NOx removal of more than 50% is achievable.

Selective NOx recirculation (SNR), involving adsorption, selective external recirculation and decomposition of the NOx by the combustion process, is itself a promising technique to abate NOx emissions. Three types of materials containing Ba: barium aluminate, barium tin perovskite and barium Y-zeolites have been developed to adsorb NOx under lean-burn or Diesel conditions, with or without the presence of S02. All these materials adsorb NO2 selectively (lean-burn conditions), and store it as nitrate/nitrite species. The desorption takes place by decomposition of these species at higher temperatures. Nitrate formation implies also sulfate formation in the presence of SO2 and SO3, while the NO2/SO2 competition governs the poisoning of such catalysts.

The combustion process of a heavy-duty DI-Diesel truck engine has been investigated using numerical simulation. The numerical modeling was based on an improved version of the KIVA-2 engine simulation code, employing a modified characteristic time-scale combustion model and a modified Kelvin-Helmholtz spray atomization model. The NO-formation process was modeled using the extended thermal Zeldovich mechanism. The simulation efforts included the effects of different injection characteristics such as varying the injection rate profile or number of injection holes and sizes. The physical sub-models used to improve the simulation of the mixture-formation and the combustion process were validated through comparison with single-cylinder engine experiments. Special attention was given to accurately model the in-cylinder flame propagation of the individual sprays and their effect on thermal NO-formation. All simulations were based on full load cases at medium speed.

In his paper “The Knock Syndrome - its Cures and its Victims” (SAE 841339) Oppenheim proposed to change the whole process of the internal combustion engine replacing moving flames by homogeneous and simultaneous combustion. Intensive research work on flame propagation and auto-ignition phenomena led to new insights into combustion over recent years. The implementation of auto-ignition on two-stroke S.I. engines revealed the potential for simultaneous reductions in fuel consumption and NOx emission. Deploying the principle for the four-stroke piston engine and standard fuel would provide optimum conditions for application in common vehicles. The basic problem of homogeneous combustion is presented and some options of control are discussed. A methodology is proposed to apply a new type of combustion simply through a consistent combination of modern technology available for the S.I. engine.

Chemiluminescence imaging has been applied to a parametric investigation of diesel autoignition. Time-resolved images of the natural light emission were made in an optically accessible DI diesel engine of the heavy-duty size class using an intensified CCD video camera. Measurements were obtained at a base operating condition, corresponding to a motored TDC temperature and density of 992 K and 16.6 kg/m3, and for TDC temperatures and densities above and below these values. Data were taken with a 42.5 cetane number blend of the diesel reference fuels for all conditions, and measurements were also made with no. 2 diesel fuel (D2) at the base condition. For each condition, temporal sequences of images were acquired from the time of first detectable chemiluminescence up through fully sooting combustion, and the images were analyzed to obtain quantitative measurements of the average emission intensity.

Extensive crash sled testing and analysis has recently led to the development of a new HANS prototypes for use in FIA F1. The performance of HANS prototypes has been studied with various conditions of HANS design geometry and impact direction. The new HANS prototypes have been found to substantially reduce injurious motions and forces of the head and neck, and the new HANS is lighter, more compact, and performs better than the currently available HANS. Use of HANS by FIA F1 drivers has been initiated.

The awareness concerning environmental issues and the economical need for fuel savings leads to the introduction of new, highly efficient Diesel engines for passenger cars. An engine with common rail injection system could meet this target and, with the help of an advanced diesel exhaust aftertreatment system also fulfilled the new legislative emission regulations. Besides the efficient oxidation of carbon monoxide (CO), hydrocarbons (HC) and diesel particulates, such a system also requires a moderate reduction efficiency for nitrogen oxides (NOx) under excess oxygen conditions. The present paper illustrates the further progress in catalytic NOx-reduction under excess of oxygen by hydrocarbon enrichment using the common rail injection system.

A detailed, one-dimensional, time dependend model is presented, describing flame kernel development in spark ignition engines which explicitely accounts for all fundamental properties of the ignition system (supplied electrical energy and power, discharge mode, energy transfer efficiency to spark plasma, plasma temperature distribution, gap width, heat losses to electrodes and chamber walls), of the combustible mixture (pressure, temperature, equivalence ratio, residual gas fraction, laminar burning velocity, type of fuel) and of the flow field (mean flow velocity, turbulence intensity, strain, characteristic time and length scales, flame holder effects). The model is based on the strained flamelet model and predicts kernel growth consistently under virtual all relevant physical/chemical conditions. Model predictions have been verified in extensive studies in an optical engine over a wide range of physical/chemical parameters using advanced optical and laser optical diagnostics.

Realization of the leanburn SI engine's potential for improved fuel economy strongly depends on precise control of the air-fuel ratio (AFR), especially during transients, for acceptable driveability and low exhaust emissions. The development of an adaptive-feedforward model-based AFR controller is described. A discrete, nonlinear, control-oriented engine model was developed and used in the AFR control algorithm. The engine model includes intake-manifold airflow dynamics, fuel wall-wetting dynamics, process delays inherent in the four-stroke engine cycle, and exhaust-gas oxygen (UEGO) sensor dynamics. The sampling period is synchronous with crank-angle (“event-based”) for more precise control. The controller relies on the engine speed and throttle position for load information. An intake-manifold pressure (MAP) sensor is used for identification of the airflow dynamics, but not for control. The MAP sensor would also be useful for the cold start and for engine diagnostics.

One possibility to improve the fuel economy of SI-engines is to run the engine with a lean air-fuel-ratio (AFR). Hydrocarbon and carbon monoxide after-treatment has been proven under lean operation, but NOx-control remains a challenge to catalyst and car manufacturers. One strategy that is being considered is to run the engine lean with occasional operation at stoichiometry. This would be in conjunction with a three-way-catalyst (TWC) to achieve stoichiometric conversion of the three main pollutants in the normal way and a NOx trap. The NOx trap stores NOx under lean operation to be released and reduced under rich conditions. The trap also functions as a TWC and has good HC and CO conversion at both lean and stoichiometric AFR's. Under lean conditions NO is oxidised to NO2 on Pt which is then adsorbed on an oxide surface. Typical adsorbent materials include oxides of potassium, calcium, zirconium, strontium, lanthanum, cerium and barium.

The use of pistons made of fine grain carbon was investigated in a spark-ignition engine within a European Community funded research project (TPRO-CT92-0008). Pistons were designed and manufactured and then tested in a single cylinder engine. Due to the carbon material's lower coefficient of thermal expansion the top land clearance between piston and cylinder can be reduced by a factor of three in comparison to standard aluminium designs. Under steady-state part-load operating conditions the emission of unburned hydrocarbons can be reduced by more than 15% compared to aluminium pistons, without significant penalties in NOx-emissions. Simultaneously, a small improvement in fuel economy of about 2% is observed. At full-load blow-by leakage flow is reduced by more than 50%. The piston crown temperature is about 30°C higher with the carbon piston than with the standard aluminium piston, due to the lower thermal conductivity of the carbon material.

Absolute two-dimensional concentration distributions of nitric oxide have been measured in a fully transparent square piston engine with planar laser induced fluorescence. A calibration procedure was used to obtain absolute NO concentrations. The NO formation was studied in the propane/air fueled engine as a function of air/fuel ratio, crank angle and load. Simultaneous measurements of NO distributions by LIF and temperature fields via Rayleigh scattering allowed to study the correlation of NO formation and temperature. It was found that the measured NO was mainly formed via the Zeldovich mechanism.

Quantitative Laser-Induced Incandescence (LII) has been applied to investigate the soot formation in a combusting Diesel jet for various conditions. For the quantification of the LII signal the local soot volume fraction of a diffusion flame burner was measured using laser beam extinction. These data were used for the calibration of the LII signal. The investigation of the soot formation in a combusting Diesel jet was performed in a high pressure, high temperature combustion chamber with optical access. A wide range of pressure (up to 10 MPa) and temperature (up to 1,500 K) conditions could be covered using a hydrogen precombustion, which is initiated inside the chamber before fuel injection. The influence of different gas atmospheres have been investigated by varying the gas composition (H2, O2 and N2) inside the chamber.

Engine and laboratory tests were carried out to examine the performance of NOx adsorption catalysts for gasoline lean burn engines in fresh and aged condition. The results show that fresh NOx adsorption catalysts have the potential to meet EURO III emission standards. However, to accomplish these the fuel must contain a low sulfur concentration and the engine must be tuned to optimize the efficiency of the catalyst. After engine or furnace aging upto 750°C the catalyst shows some loss of NOx adsorption efficiency. This deterioration can be offset somewhat by increasing the frequency of lean/rich switching of the engine. Temperatures higher than 750°C may cause an irreversible destruction of the NOx, storage features while the three-way activity of the catalyst remains intact or even may improve. With reference to several physicochemical investigations it is believed that the detrimental effect of catalyst aging is attributed to two different deactivation modes.

After dealing briefly with the mode of operation of the Comprex® pressure wave supercharger, a report is given on its general advantages and drawbacks as well as on experience gained in practical operations on the supercharging system, using a 2.2 dm3 prechamber passenger car diesel engine. The most important problems which occurred here and the performance and exhaust emission figures resulting from rig and road test measurements are discussed.