Refine Your Search

Topic

Author

Affiliation

Search Results

Technical Paper

A Hardware-in-the-loop Test Bench for Production Transmission Controls Software Quality Validation

2007-04-16
2007-01-0502
Production software validation is critical during software development, allowing potential quality issues that could occur in the field to be minimized. By developing automated and repeatable software test methods, test cases can be created to validate targeted areas of the control software for confirmation of the expected results from software release to release. This is especially important when algorithm/software development timing is aggressive and the management of development activities in a global work environment requires high quality, and timely test results. This paper presents a hardware-in-the-loop (HIL) test bench for the validation of production transmission controls software. The powertrain model used within the HIL consists of an engine model and a detailed automatic transmission dynamics model. The model runs in an OPAL-RT TestDrive based HIL system.
Technical Paper

Clutch-to-Clutch Transmission Control Strategy

2007-04-16
2007-01-1313
An automatic transmission control system for clutch-to-clutch shifting systems has been developed. This enables the new General Motors Powertrain families of rear- and front-wheel drive transmissions to meet stringent cost, mass, and packaging reqiurements, while providing driveability and fuel economy improvements over the four- and five-speed transmissions that they replace. The design team utilized several new technologies and methods to robustly engineer a control system that allowed excellent first time capability and reduced calibration intensity. Innovative technical approaches were developed in several key mechatronics areas.
Technical Paper

Investigation of Hydrocarbon Emissions from a Direct Injection-Gasoline Premixed Charge Compression Ignited Engine

2002-03-04
2002-01-0419
The causes of Unburned Hydrocarbon (UHC) emissions from a premixed compression ignited engine were investigated for both homogeneous and stratified charge conditions. A fast response Flame Ionization Detector (fast FID) was used to provide cycle-resolved UHC exhaust emission measurements. These fast FID UHC measurements were coupled with numerical flow simulation results to provide quantitative and qualitative insight into the sources of UHC emissions. The combined results were used to evaluate the effects of engine load, local gas temperatures, fuel stratification, and crevice quenching on UHC emissions.
Technical Paper

Experimental Investigation of Direct Injection-Gasoline for Premixed Compression Ignited Combustion Phasing Control

2002-03-04
2002-01-0418
A direct injection-gasoline (DI-G) system was applied to a heavy-duty diesel-type engine to study the effects of charge stratification on the performance of premixed compression ignited combustion. The effects of the fuel injection parameters on combustion phasing were of primary interest. The simultaneous effects of the fuel stratification on Unburned Hydrocarbon (UHC), Oxides of Nitrogen (NOx), Carbon Monoxide (CO), and smoke emissions were also measured. Engine tests were conducted with altered injection parameters covering the entire load range of normally aspirated Homogeneous Charge Compression Ignited (HCCI) combustion. Combustion phasing tests were also conducted at several engine speeds to evaluate its effects on a fuel stratification strategy.
Technical Paper

General Motors Hydra-Matic & Ford New FWD Six-Speed Automatic Transmission Family

2007-04-16
2007-01-1095
The Hydra-Matic 6T70 is General Motors first model of a new, two-variant front wheel drive (FWD) six speed automatic transmission family. The second variant is a higher capacity model, the 6T75. The transmission was co-developed with Ford Motor Company. The 6F50 is the Ford variant that aligns with the GM 6T70 transmission. Approximately eighty five percent of the hardware is shared or common between the GM and Ford transmission variants. Ford will also have a higher capacity variant the 6F55 to align with the GM 6T75. The first GM application is the Saturn Aura for the 2007 Model Year. The Ford Edge and Lincoln MKX in MY 2007 will be the first applications for the 6F50. While the Hydra-Matic and Ford FWD six-speed family was designed with two variants in mind, the designed in modularity requires only changes to the second and third axis and case housings depending on specific torque requirements. This modular design enables a tremendous amount of part sharing.
Technical Paper

Characterization of a Catalytic Converter Internal Flow

2007-10-29
2007-01-4024
This paper includes a numerical and experimental study of fluid flow in automotive catalytic converters. The numerical work involves using computational fluid dynamics (CFD) to perform three-dimensional calculations of turbulent flow in an inlet pipe, inlet cone, catalyst substrate (porous medium), outlet cone, and outlet pipe. The experimental work includes using hot-wire anemometry to measure the velocity profile at the outlet of the catalyst substrate, and pressure drop measurements across the system. Very often, the designer may have to resort to offset inlet and outlet cones, or angled inlet pipes due to space limitations. Hence, it is very difficult to achieve a good flow distribution at the inlet cross section of the catalyst substrate. Therefore, it is important to study the effect of the geometry of the catalytic converter on flow uniformity in the substrate.
Technical Paper

Economic Analysis of Powertrain Control Technologies

2002-10-21
2002-21-0035
Regulatory and market pressures continue to challenge the automotive industry to develop technologies focused on reducing exhaust emissions and improving fuel economy. This paper introduces a practical model, which evaluates the economic value of various technologies based on their ability to reduce fuel consumption, improve emissions or provide consumer benefits such as improved performance. By evaluating the individual elements of economic value as viewed by the OEM manufacturer, while keeping the end consumer in mind, technology selection decisions can be made. These elements include annual fuel usage, vehicle performance, mass reduction and emissions, among others. The following technologies are discussed and evaluated: gasoline direct injection, variable valvetrain technologies, common-rail diesel and hybrid vehicles.
Technical Paper

Design of an Automotive Grade Controller for In-Cylinder Pressure Based Engine Control Development

2007-04-16
2007-01-0774
This paper describes a new tool to capture cylinder pressure information, calculate combustion parameters, and implement control algorithms. There are numerous instrumentation and prototyping systems which can provide some or all of this capability. The Cylinder Pressure Development Controller (CPDC) is unique in that it uses advanced high volume automotive grade circuitry, packaging, and software methodologies. This approach provides insight regarding the implementation of cylinder pressure based controls in a production engine management system. A high performance data acquisition system is described along with a data reduction technique to minimize data processing requirements. The CPDC software architecture is discussed along with model-based algorithm development and autocoding. Finally, CPDC calculated combustion parameters are compared with those from a well established combustion analysis system and thermodynamic simulations.
Technical Paper

Cylinder Pressure-Based Control of Pre-Mixed Diesel Combustion

2007-04-16
2007-01-0773
Implementation of real-time combustion feedback for use in closed-loop combustion control is a technology that has potential to assist in the successful production implementation of advanced diesel combustion modes. Low-temperature, pre-mixed diesel combustion is presently of interest because it offers the ability to lower the engine-out emissions of oxides of nitrogen (NOx) and particulate matter (PM). The need for lowering these two emissions is driven by tighter regulations enacted worldwide, especially the NOx limits in the United States. Reducing engine-out emissions eases the need for additional exhaust aftertreatment devices and their associated cost and mass. In this paper we will describe an experimental cylinder pressure-based control system and present both steady-state and transient results from a diesel engine employing a pre-mixed type of combustion.
Technical Paper

Evaluation of the MADYMO Full FE Human Model in a Rear Impact Simulation of an IndyCar

2006-12-05
2006-01-3659
Computer simulation was used as a complement to crash and injury field data analysis and physical sled and barrier tests to investigate and predict the spinal injuries of a rear impact in an IndyCar. The model was expected to relate the spinal loads to the observed injuries, thereby predicting the probability and location of spinal fractures. The final goal is to help reduce the fracture risk by optimizing the seat and restraint system design and the driver's position using computer modeling and sled testing. MADYMO Full FE Human Body Model (HBM) was selected for use because of its full spinal structural details and its compatibility with the vehicle and restraint system models. However, the IndyCar application imposed unique challenges to the HBM. First, the driver position in a race car is very different from that in a typical passenger car.
Technical Paper

Application of Robust Engineering Methods to Improve ECU Software Testing

2006-04-03
2006-01-1600
Robust Engineering techniques developed by Taguchi have traditionally applied to the optimization of engineering designs. Robust Engineering methods also may be applied to software testing of ECU algorithms. The net result is an approach capable of improving the software algorithm in one of two ways. First the approach can identify the range of areas which prove problematic to the software such that a robust solution may be developed. Conversely, the approach can be used as a general strategy to verify that the software is robust over the range of inputs tested. The robust engineering methods applied to software testing utilize orthogonal array experiments to test software over a range of inputs. The actual software trials are best performed in the simulation environment and also via automated test hardware in the loop configurations in realtime. This paper outlines a process for applying Robust Engineering methods to software testing.
Technical Paper

Experimental Evaluation of R134a Emission with Various Hose Constructions

2005-05-10
2005-01-2032
The focus of this paper is to understand, from experimental data, the R134a refrigerant emission rates of various hose materials due to permeation. This paper focuses on four main points for hose assembly emission of R134a: (1) characteristics of hose permeation in response to the effect of oil in R134a and the characteristics of hose permeation of vapor vs. liquid refrigerant; (2) conditioning of the hose material over time to reach steady state R134a emission; (3) the relative contribution of hose permeation and coupling emission to the overall hose assembly refrigerant emission; (4) transient emission rates due to transient temperature and pressure conditions. Studies include hoses with different materials and constructions resulting in various levels of R134a permeation.
Technical Paper

Improving Cam Phaser Performance Using Robust Engineering Techniques

2005-10-24
2005-01-3903
This paper describes a robust engineering DOE (design of experiment) completed by hydraulic simulation of a Variable Cam Phaser System based on an L4 IC engine. The robust engineering study focused on the high temperature and low speed portions of overall engine operating conditions where the cam phase rates are slow and oscillation is high. The analysis included a preliminary DOE with multiple noise variables used as the control factors in order to quantify and compound the factors into just two noise levels; best and worst conditions. Following the noise DOE, a larger DOE study was completed with 16 control variables including phaser, oil control valve and various engine parameters. It was run at 3 engine rpm (signal levels), 2 noise levels, and was analyzed for 3 responses (advancing rate, retarding rate, and oscillation amplitude while holding an intermediate position). These DOE experiments determined potential gains for each design proposal.
Technical Paper

A Systematic Experimental Investigation of Pd-Based Light-Off Catalysts

2005-10-24
2005-01-3848
Close-coupled or manifold catalysts have been extensively employed to reduce emissions during cold start by achieving quick catalyst light-off. These catalysts must have good thermal durability, high intrinsic light-off activity and high HC/CO/NOx conversions at high temperature and flow conditions. A number of studies have been dedicated to engine control, manifold design and converter optimization to reduce cold start emissions. The current paper focuses on the effect of catalyst design parameters and their performance response to different engine operating conditions. Key design parameters such as catalyst formulation (CeO2 vs. non CeO2), precious metal loading and composition (Pd vs. Pd/Rh), washcoat loading, catalyst thermal mass, substrate properties and key application (in use) parameters such as catalyst aging, exhaust A/F ratio, A/F ratio modulation, exhaust temperature, temperature rise rate and exhaust flow rate were studied on engine dynamometers in a systematic manner.
Technical Paper

Mixed-H2/H∞ Suspension Control Synthesis for Ride & Handling Enhancement

2005-05-16
2005-01-2547
Active/semi-active suspension control of a passenger vehicle is a classic problem involving multiple-objectives, all of which cannot be simultaneously achieved without compromises between ride and handling performance. Traditionally, suspension control tuning has been a subjective process that involves tuning of hundreds of parameters. This paper attempts to add some level of objectivity to the tuning philosophy by posing the ride/handling trade-off as a multi-constrained, multi-objective optimization problem and solving it using a mixed-H2/H∞ control synthesis technique to obtain a pareto-optimal solution. The multi-variable constrained optimization problem involves minimization of body control metrics subject to constraints defined by wheel-control metrics (a measure of road-holding capability). Simulation as well as road-test results clearly demonstrate the effectiveness and impact the proposed control strategy has on improving ride and handling performance.
Technical Paper

2-step Variable Valve Actuation: System Optimization and Integration on an SI Engine

2006-04-03
2006-01-0040
2-step variable valve actuation using early-intake valve closing is a strategy for high fuel economy on spark-ignited gasoline engines. Two discrete valve-lift profiles are used with continuously variable cam phasing. 2-step VVA systems are attractive because of their low cost/benefit, relative simplicity, and ease-of-packaging on new and existing engines. A 2-step VVA system was designed and integrated on a 4-valve-per-cylinder 4.2L line-6 engine. Simulation tools were used to develop valve lift profiles for high fuel economy and low NOx emissions. The intake lift profiles had equal lift for both valves and were designed for high airflow & residual capacity in order to minimize valvetrain switching during the EPA drive cycle. It was determined that an enhanced combustion system was needed to maximize fuel economy benefit with the selected valve lift profiles. A flow-efficient chamber mask was developed to increase in-cylinder tumble motion and combustion rates.
Technical Paper

Design and Testing of a Prototype Midsize Parallel Hybrid-Electric Sport Utility

2004-10-25
2004-01-3062
The University of Wisconsin - Madison hybrid vehicle team has designed and constructed a four-wheel drive, charge sustaining, parallel hybrid-electric sport utility vehicle for entry into the FutureTruck 2003 competition. This is a multi-year project utilizing a 2002 4.0 liter Ford Explorer as the base vehicle. Wisconsin's FutureTruck, nicknamed the ‘Moolander’, weighs 2000 kg and includes a prototype aluminum frame. The Moolander uses a high efficiency, 1.8 liter, common rail, turbo-charged, compression ignition direct injection (CIDI) engine supplying 85 kW of peak power and an AC induction motor that provides an additional 60 kW of peak power. The 145 kW hybrid drivetrain will out-accelerate the stock V6 powertrain while producing similar emissions and drastically reducing fuel consumption. The PNGV Systems Analysis Toolkit (PSAT) model predicts a Federal Testing Procedure (FTP) combined driving cycle fuel economy of 16.05 km/L (37.8 mpg).
Technical Paper

Evaluation of Power Devices for Automotive Hybrid and 42V Based Systems

2004-03-08
2004-01-1682
With the requirements for reducing the emissions and improving the fuel economy, the automotive companies are developing hybrid, 42 V and fuel cell vehicles. Power electronics is an enabling technology for the development of environmental friendly vehicles, and to implement the various vehicle electrical architectures to obtain the best performance. In this paper, the requirements of the power semiconductor devices and the criteria for selecting the power devices for various types of low emission vehicles are presented. A comparative study of the most commonly used power devices is presented. A brief review of the future power devices that would enhance the performance of the automotive power conversion systems is also presented.
Technical Paper

Evaluation and Comparison of CFD Integrated Airbag Models in LS-DYNA, MADYMO and PAM-CRASH

2004-03-08
2004-01-1627
The interaction between the deploying airbag and the Out-Of-Position (OOP) occupants remains a challenge in occupant protection system simulations. The integration of Computational Fluid Dynamics (CFD) analysis into Finite Element (FE) airbag model is a helpful and important tool to address this challenge. Three major commercial crash simulation software packages widely used in the automotive safety industry, LS-DYNA, MADYMO and PAM-CRASH are in the process of implementing different approaches for airbag CFD simulation. In this study, an attempt was made to evaluate and compare the CFD integrated airbag models in these software packages. Specially designed tests were conducted to study and capture the pressure distribution inside a flat airbag and the test results were used for the evaluation. Strengths and limitations of each software package are discussed in this paper.
X