Refine Your Search

Topic

Author

Affiliation

Search Results

Technical Paper

Numerical Investigation of Flow Induced Excitations in a Torque Converter

2017-03-28
2017-01-1115
This study analyzes the flow dynamics of a fluid within an operating torque converter. Transient computational fluid dynamics (CFD) simulations have been carried out with prescribed torque converter motions using commercially available CFD software. The analysis computes torque converter excitation forces that predict flow induced excitations during converter operation. In this study, various torque converter designs are compared and assessed with the aim of limiting flow induced excitations.
Technical Paper

A New Weight Reduction Lightening Holes Development Approach Based on Frame Durability Fatigue Performance

2017-03-28
2017-01-1348
For a light duty truck, the frame is a structural system and it must go through a series of proving ground events to meet fatigue performance requirement. Nowadays, in order to meet stringent CAFE standards, auto manufacturers are seeking to keep the vehicle weight as light as possible. The weight reduction on the frame is a challenging task as it still needs to maintain the strength, safety, and durability fatigue performance. CAE fatigue simulation is widely used in frame design before the physical proving ground tests are performed. A typical frame durability fatigue analysis includes both the base metal fatigue analysis and seam weld fatigue analysis. Usually the gauges of the frame components are dictated by the seam weld fatigue performance so opportunities for weight reduction may exist in areas away from the welds. One method to reduce frame weight is to cut lightening holes in the areas that have little impact on the frame fatigue performance.
Technical Paper

Optimizing the Rear Fascia Cutline Based On Investigating Deviation Sources of the Body Panel Fit and Finish

2017-03-28
2017-01-1600
A vehicle’s exterior fit and finish, in general, is the first system to attract customers. Automotive exterior engineers were motivated in the past few years to increase their focus on how to optimize the vehicle’s exterior panels split lines quality and how to minimize variation in fit and finish addressing customer and market required quality standards. The design engineering’s focus is to control the deviation from nominal build objective and minimize it. The fitting process follows an optimization model with the exterior panel’s location and orientation factors as independent variables. This research focuses on addressing the source of variation “contributed factors” that will impact the quality of the fit and finish. These critical factors could be resulted from the design process, product process, or an assembly process. An empirical analysis will be used to minimize the fit and finish deviation.
Technical Paper

Simplified Approach for Optimizing Lightening Holes in Truck Frames for Durability Performance

2017-03-28
2017-01-1345
During development of new vehicles, CAE driven optimizations are helpful in achieving the optimal designs. In the early phase of vehicle development there is an opportunity to explore shape changes, gage reduction or alternative materials as enablers to reduce weight. However, in later phases of vehicle development the window of opportunity closes on most of the enablers discussed above. The paper discusses a simplified methodology for reducing the weight in design cycle for truck frames using parametric Design of Experiments (DOE). In body-on-frame vehicles, reducing the weight of the frame in the design cycle without down gaging involves introducing lightening holes or cutouts while still maintaining the fatigue life. It is also known that the lightening holes might cause stress risers and be detrimental to the fatigue life of the component. Thus the ability to identify cutout locations while maintaining the durability performance becomes very critical.
Technical Paper

Pattern Generation Based Instrument Cluster Virtual Validation

2017-03-28
2017-01-1678
Modern Instrument Panel Clusters (IPC) are equipped with thin film transistor (TFT) based displays. Contrary to conventional IPCs with hard gauges and liquid crystal diode (LCD) displays, TFT displays offer versatile usage of display area with soft gauges, reconfigurable menus, tell tales, graphics and warning messages etc., At the same time, the number of possible screen combinations, multicolor images validation and different screen arbitration become significantly complex. Thereby display validation turns out to be a complex and time consuming task in IPC validation. The task becomes even more complex when change requests are to be incorporated during final phases of development stage. This paper provides a novel solution that helps to validate any graphical and behavioral changes with minimum effort and maximum accuracy.
Technical Paper

Optimal Water Jacket Flow Distribution Using a New Group-Based Space-Filling Design of Experiments Algorithm

2018-04-03
2018-01-1017
The availability of computational resources has enabled an increased utilization of Design of Experiments (DoE) and metamodeling (response surface generation) for large-scale optimization problems. Despite algorithmic advances however, the analysis of systems such as water jackets of an automotive engine, can be computationally demanding in part due to the required accuracy of metamodels. Because the metamodels may have many inputs, their accuracy depends on the number of training points and how well they cover the entire design (input) space. For this reason, the space-filling properties of the DoE are very important. This paper utilizes a new group-based DoE algorithm with space-filling groups of points to construct a metamodel. Points are added sequentially so that the space-filling properties of the entire group of points is preserved. The addition of points is continuous until a specified metamodel accuracy is met.
Technical Paper

Mode-shifting Minimization in a Power Management Strategy for Rapid Component Sizing of Multimode Power Split Hybrid Vehicles

2018-04-03
2018-01-1018
The production of multi-mode power-split hybrid vehicles has been implemented for some years now and it is expected to continually grow over the next decade. Control strategy still represents one of the most challenging aspects in the design of these vehicles. Finding an effective strategy to obtain the optimal solution with light computational cost is not trivial. In previous publications, a Power-weighted Efficiency Analysis for Rapid Sizing (PEARS) algorithm was found to be a very promising solution. The issue with implementing a PEARS technique is that it generates an unrealistic mode-shifting schedule. In this paper, the problematic points of PEARS algorithm are detected and analyzed, then a solution to minimize mode-shifting events is proposed. The improved PEARS algorithm is integrated in a design methodology that can generate and test several candidate powertrains in a short period of time.
Technical Paper

A Comprehensive Study of Hole Punching Force for AHSS

2018-04-03
2018-01-0802
The elevated strength of advanced high strength steels (AHSS) leads to enormous challenges for the sheet metal processing, one of which is hole punching operation. The total tonnage must be estimated at each trimming stage to ensure successful cutting and protect the press machine. This paper presents the effects of hole punch configurations on the punching force with the consideration of punch shape, cutting clearance and material grade. The hole punching experiments were performed with DP590, DP980, DP1180 and one mild steel as a reference. The punching force coefficient is defined and presents a negative correlation with the material strength based on the experimental data. Surface quality was examined to analyze the damage accumulation during the punching process. The cutting mechanisms with various punch shapes were revealed through an extensive finite element simulation study.
Technical Paper

Numerical Study of Twist Spring-back Control with an Unbalanced Post-stretching Approach for Advanced High Strength Steel

2018-04-03
2018-01-0806
Twist spring-back would interfere with stamping or assembling procedures for advanced high strength steel. A “homeopathic” resolution for controlling the twist spring-back is proposed using unbalanced post-stretching configuration. Finite element forming simulation is applied to evaluate and compare the performance for each set of unbalanced post-stretching setup. The post-stretching is effectuated by stake bead application. The beads are separated into multiple independent segments, the height and radii of which can be adjusted individually and asymmetrically. Simulation results indicate that the twist spring-back can be effectively controlled by reducing the post-stretching proximate to the asymmetric part area. Its mechanism is qualitatively revealed by stress analyses, that an additional but acceptable cross-sectional spring-back re-balances the sprung asymmetrical geometry to counter the twist effect.
Technical Paper

Effects of Punch Shapes and Cutting Configurations on the Dimensional Accuracy of Punched Holes on an AHSS Sheet

2018-04-03
2018-01-0800
Dimensional accuracy of punched hole is an essential consideration for high-quality sheet metal forming. An out-of-shape hole can give rise to manufacturing issues in the subsequent production processes thus inducing quality defects on a vehicle body. To understand the effects of punch shapes and cutting configurations on punched hole diameter deviations, a systematical experimental study was conducted for multiple types of AHSS (DP1180, DP980, DP590) and one mild steel. Flat, conical and rooftop punches were tested respectively with three cutting clearances on each material. The measurement results indicated different diameter enlargement modes based on the punch profiles, and dimensional discrepancies were found to be more significant with the stronger materials and higher cutting clearance. To uncover the mechanism of punched hole enlargement, a series of finite element simulations were established for numerical investigation.
Technical Paper

Study of Incremental Bending Test on Aluminum Sheets

2018-04-03
2018-01-0807
Bendability is one of the most important formability characteristics in sheet metal forming, so it has to be understood for robust aluminum stamping process designs. Crack is one of the major failure modes in aluminum sheet bending. In this study, a new “incremental bending” method is proposed to reduce the risk of bending failure. A novel laboratory test methodology is conducted to test the 5xxx series aluminum sheet bendability with 3D digital image correlation (DIC) measurement system. The designs of test apparatus and test procedure are introduced in this paper. Through the data processing and evaluation of a sequence image acquisition, the major strain histories within the zone of the through thickness crack of test samples are measured. Testing results show that incremental bending is capable of reducing peak strain on the outer surface obviously compared with traditional non-incremental bending. The more step, more movement, the more peak strain reduction.
Technical Paper

Study on Frictional Behavior of AA 6XXX with Three Lube Conditions in Sheet Metal Forming

2018-04-03
2018-01-0810
Light-weighting vehicles cause an increase in Aluminum Alloy stamping processes in the Automotive Industry. Surface finish and lubricants of aluminum alloy (AA) sheet play an important role in the deep drawing processes as they can affect the friction condition between the die and the sheet. This paper aims to develop a reliable and practical laboratory test method to experimentally investigate the influence of surface finish, lubricant conditions, draw-bead clearances and pulling speed on the frictional sliding behavior of AA 6XXX sheet metal. A new double-beads draw-bead-simulator (DBS) system was used to conduct the simulated test to determine the frictional behavior of an aluminium alloy with three surface lubricant conditions: mill finish (MF) with oil lube, electric discharge texture (EDT) finish with oil lube and mill finish (MF) with dry lube (DL).
Technical Paper

Detailed Aerodynamic Characterization and Optimization of a Pickup Truck Using Adaptive Sampling based DOE

2018-04-03
2018-01-0743
A detailed Design of Experiments (DOE) study is presented to understand the aerodynamic effects of exterior design features and shape parameters of a pick-up truck using Computational Fluid Dynamics (CFD). The goal of the study is to characterize several key design parameters and the interactions between them as related to overall drag of the vehicle. Using this data, the exterior shape is optimized to minimize drag within specified design constraints. An adaptive sampling methodology is also presented that progressively reduces errors in the design response surfaces generated. This combined with a Latin Hypercube based initial design space characterization yields computational efficiency. A trend-predictive meta-model is presented that can be used for early design development. Results from the meta-model are also correlated with experimental data from the wind tunnel.
Technical Paper

CAE Simulation of Automotive Door Upper Frame Deflection Using Aerodynamic Loads

2018-04-03
2018-01-0716
Upper frame deflection of automobile doors is a key design attribute that influences structural integrity and door seal performance as related to NVH. This is a critical customer quality perception attribute and is a key enabler to ensure wind noise performance is acceptable. This paper provides an overview of two simulation methodologies to predict door upper frame deflection. A simplified simulation approach using point loads is presented along with its limitations and is compared to a new method that uses CFD tools to estimate aerodynamic loads on body panels at various vehicle speeds and wind directions. The approach consisted of performing external aerodynamic CFD simulation and using the aerodynamic loads as inputs to a CAE simulation. The details of the methodology are presented along with results and correlation to experimental data from the wind tunnel.
Technical Paper

Vehicle Attitude Changes from Aerodynamic Forces

2018-04-03
2018-01-0711
A vehicle driving down the road naturally pitches, rolls and heaves due to road inputs (for example, bumps, potholes, driving dynamics, etc.) and also due to the influence of aerodynamic forces. The vehicle attitude changes directly as a result of aerodynamic forces that can be seen during wind tunnel testing of production level vehicles, with some measurements possible in order to evaluate the aerodynamics effects. This naturally occurring phenomenon is not always represented in aerodynamics simulations, either for reduced scale models or computational fluid dynamics (CFD) simulations or even rigid body full scale testing. It can be shown through visual techniques how much deflection is typically occurring, including both vehicle attitude changes as well as vehicle body distortions. From the analysis, an adjustment to the CFD models can be made to compensate for the aerodynamics effects.
Technical Paper

Field Fatigue Failure Prediction Using Multiple Regression with Random Variables

2018-04-03
2018-01-1106
The most common used warranty prediction method at component level (non-repairable system) is called Weibull analysis. In Weibull analysis, failure time is assumed to follow a certain distribution such as Weibull, and time is the only predictor in the model for predicting percentage of failures. However, other variables such as design variables, manufacturing parameters, and field use condition also affect warranty. These variables should be considered in the prediction. In this paper, a multiple regression approach is proposed to predict warranty failures of a solenoid switch by considering multiple factors that affect the warranty. A single failure mode caused by fatigue is studied. The failure is caused by out of GD&T (Geometric Dimension and Tolerance) specs. These GD&T variables together with component operation time are used as predictors in the model. The final model is established by integrating physics of failures with statistical analysis results.
Technical Paper

Cooling Capable Vehicle Front End Concepts Development: Response Surface Approach

2018-04-03
2018-01-1194
The paper describes a process for rapid development of cooling capable front-end concepts for a vehicle based on an architecture, and a tool (Vehicle Parametric Model for Cooling) developed to execute the process. The process involves upfront definition of allowable ranges of several parameters related to the vehicle front end that affect cooling. The tool is based on characterizing airflow through Computational Fluid Dynamics (CFD) simulations and engine coolant temperature through one-dimensional (1D) thermal balance methods over the architectural domain in the form of a multi-parameter Response Surface using the Approximation Model provided by Isight. The number of sampling points needed for the Approximation is minimized by employing Design of Experiments (DOE) methods, while ensuring sufficient accuracy consistent with the goals of intended use of the Tool.
Technical Paper

Lumped Parameter Based Thermo-Physical Modeling of Electrified Vehicle Transmission System

2018-04-03
2018-01-1195
More stringent Federal emission regulations and fuel economy requirements have driven the automotive industry toward more efficient vehicle thermal management systems to best utilize the heat produced from burning fuel and improve driveline efficiency. The greatest part of the effort is directed toward the hybridization of automotive transmission systems. The efficiency and durability of hybrid powertrain depends on the heat generation in electric motors and their interactions among each other, ambient condition, the cooling system and the transmission component configuration. These increase the complexity of motor temperature prediction as well as the computational cost of running a conjugate heat-transfer based CFD analysis. In this paper, 1D physics based thermal model is developed which allows rapid and accurate component-wise temperature estimation of the electric motor during both steady-state and transient driving cycles.
Technical Paper

Study of Ausferrite Transformation Kinetics for Austempered Ductile Irons with and without Ni

2016-04-05
2016-01-0421
This research studies the transformation kinetics of austempered ductile iron (ADI) with and without nickel as the main alloying element. ADI has improved mechanical properties compared to ductile iron due to its ausferrite microstructure. Not only can austempered ductile iron be produced with high strength, high toughness and high wear resistance, the ductility of ADI can also be increased due to high carbon content austenite. Many factors influence the transformation of phases in ADI. In the present work, the addition of nickel was investigated based on transformation kinetics and metallography observation. The transformation fractions were determined by Rockwell hardness variations of ADI specimens. The calculation of transformation kinetics and activation energy using the “Avrami Equation” and “Arrhenius Equation” is done to describe effects of nickel alloy for phase reactions.
Technical Paper

Total Thermal Management of Battery Electric Vehicles (BEVs)

2018-05-30
2018-37-0026
The key hurdles to achieving wide consumer acceptance of battery electric vehicles (BEVs) are weather-dependent drive range, higher cost, and limited battery life. These translate into a strong need to reduce a significant energy drain and resulting drive range loss due to auxiliary electrical loads the predominant of which is the cabin thermal management load. Studies have shown that thermal sub-system loads can reduce the drive range by as much as 45% under ambient temperatures below −10 °C. Often, cabin heating relies purely on positive temperature coefficient (PTC) resistive heating, contributing to a significant range loss. Reducing this range loss may improve consumer acceptance of BEVs. The authors present a unified thermal management system (UTEMPRA) that satisfies diverse thermal and design needs of the auxiliary loads in BEVs.
X