Search Results

This paper describes the process of incorporation of 25% post-industrial recycled sheet molded composite (SMC) material in the 1998 Continental Hood inner. 1998 Continental Hood assembly consists of traditional SMC outer and this recycled hood inner along with three small steel reinforcements. BUDD Plastics collects SMC scraps from their manufacturing plants. The scrap is then processed and made into fillers for production of SMC. Strength of SMC comes from glass fibers and fillers are added to produce the final mix of raw materials. This recycled material is approximately 10% lighter and less stiff than the conventional virgin SMC. This presented unique challenges to the product development team to incorporate this material into a production vehicle in order to obtain the desired goal of reducing land fill and improving the environment.

This paper describes the results of permeation and sorption tests conducted to assess the properties of several plastic materials as barriers to fuel. The materials examined include ethylene-vinyl alcohol copolymers (EVOH), nylon, high density polyethylene, polyketone, poly-vinyledene fluoride (PVDF) as well as tetra-fluoro-ethylene, hexa-fluoro-propylene and vinyledene fluoride terpolymers (THV). The permeation from thin films of these materials exposed to methanol or CM15 was analyzed (speciated) by gas chromatography. These results are compared to those of parallel sorption experiments conducted on the same materials. The goal of this work is to determine the materials best suited for fuel barrier applications.

FMVSS 207/210 relates to seat system forward longitudinal strength and is one of the most important safety requirements for seats. Seat performance to satisfy FMVSS 207/210 can be simulated using LS-DYNA FEA code. When developing a seat design there is often a need to optimize the design to satisfy requirements/meet targets and to minimize weight. However LS-DYNA does not have optimization capabilities. This paper shows how the response surface based optimization can be used to meet FMVSS 207/210 requirements and reduce weight. A number of DOE runs are performed with different combinations of upper/lower/baseline gages. Data are collected for the maximum Von Misses stress and maximum effective plastic strain in each of the major seat parts along with the total weight of the seat. Based on the collected data the response surfaces are generated using Gaussian Stochastic Kriging method.

Compressible plastic foams are used throughout the interior and bumper systems of modern automobiles for safety enhancement and damage prevention. Consequently, modeling of foams has become very important for automobile engineers. To date, most work has focused on predicting foam performance up to approximately 80% compression. However, in certain cases, it is important to predict the foam under maximum compression, or ‘bottoming-out.’ This paper uses one such case-a thin low-density bumper foam impacted by a pedestrian leg-form at 11.1 m/s-to investigate the ‘bottoming-out’ phenomenon. Multiple material models in three different explicit Finite Element Method (FEM) packages (RADIOSS, FCRASH, and LS-DYNA) were used to predict the performance. The finite element models consisted of a foam covered leg-form impacting a fixed bumper beam with a foam energy absorber.

Effects of impact velocity on the crush behavior of aluminum 5052-H38 honeycomb specimens are investigated by experiments. An impact test machine using pressurized nitrogen was designed to perform dynamic crush tests. A test fixture was designed such that inclined loads can be applied to honeycomb specimens in dynamic crush tests. The results of dynamic crush tests indicate that the effects of impact velocity on the normal and inclined crush strengths are significant. The trends of the inclined crush strengths for specimens with different in-plane orientation angles as functions of impact velocity are very similar to that of the normal crush strength. Experimental results show similar progressive folding mechanisms for honeycomb specimens under pure compressive and inclined loads. Under inclined loads, the inclined stacking patterns were observed. The inclined stacking patterns are due to the asymmetric locations of the horizontal plastic hinge lines.

The history behind Polymer Class “A” Body Panels for automotive applications is very interesting. The driving factors behind these applications have not changed significantly over the past sixty years. Foremost among these factors is the need for corrosion and dent resistance. Beginning with Saturn in 1990, interest in polymer body panels grew and continues to grow up to the present day, with every new global application. Today, consumers and economic factors drive the industry trend towards plastic body panels. These include increased customization and fuel economy on the consumer side. Economic factors such as lower unit build quantities, reduced vehicle mass, investment cost, and tooling lead times influence material choice for industry. The highest possible performance, and fuel economy, at the lowest price have always been a goal.

Residual stresses in metals are caused by a number of processes such as inhomogeneous deformation, phase changes and temperature gradients. This investigation focuses on the residual stresses caused by plastic deformation of automotive metals. Such stresses are responsible for part springback and shape distortion in many manufacturing and assembly processes. Tensile residual stresses may lead to stress cracking and, in some alloys, to stress corrosion cracking which may ultimately lead to premature product failure. The residual stress potential of metals can be evaluated by using the Split Ring Test Method. The test can be used to evaluate the effect of materials on residual stresses in cup drawing. Drawn cups are used because they produce large amounts of residual stresses and, therefore, increase measurement accuracy and reduce experimental error. A closed form analytical solution is used to estimate residual stresses in split rings taken from sections cut from the drawn cups.

Sandwich specimens with DP590 steel face sheets and structural epoxy foam cores are investigated under three-point bending conditions. Experimental results indicate that the maximum loads correspond to extensive cracking in the foam cores. Finite element simulations of the bending tests are also performed to understand the failure mechanisms of the epoxy foams. In these simulations, the plastic behavior of the steel face sheets is modeled by the Mises yield criterion with consideration of plastic strain hardening. A pressure sensitive yield criterion is used to model the plastic behavior of the epoxy foam cores. The epoxy foams are idealized to follow an elastic perfectly plastic behavior. The simulation results indicate that the load-displacement responses of some sandwich specimens agree with the experimental results.

In recent years, a special attention has been given to the environment protection, as evidenced by an increased commitment of governments and industries for a better use of energy and for reducing the levels of vehicle emissions (CO2). The use of renewable and bio-based plastics in the automotive sector is being considered as alternative solution to the conventional petroleum-based polymeric materials. In the present work, biobased polymer blends were formulated using two polyamides made from biorenewable resources. Polyamide 10,10 (PA1010) and polyamide 6,10 (PA610) were melt mixed in different compositions and the mechanical properties of the blends were investigated by tensile evaluations. The mechanical properties of the blends show intermediate values compared to the pure polymers. Significant improvements on these properties could be observed with the incorporation of PA610 in the blends.

Weld lines occur when melt flow fronts meet during the injection molding of plastic parts. It is important to investigate the weld line because the weld line area can induce potential failure of structural application. In this paper, a weld line factor (W-L factor) was adopted to describe the strength reduction to the ultimate strength due to the appearance of weld line. There were two engineering thermoplastics involved in this study, including one neat PP and one of talc filled PP plastics. The experimental design was used to investigate four main injection molding parameters (melt temperature, mold temperature, injection speed and packing pressure). Both the tensile bar samples with/without weld lines were molded at each process settings. The sample strength was obtained by the tensile tests under two levels of testing speed (5mm/min and 200mm/min) and testing temperatures (room temperature and -30°C). The results showed that different materials had various values of W-L factor.

A transmission system model is developed at various complexities in order to capture the transient behaviors in drivability and fuel economy simulations. A large number of model parameters bring more degree of freedom to correlate with vehicular test data. However, in practice, it requires extensive time and effort to tune the parameters to satisfy the model performance requirements. Among the transmission model, a hydraulic clutch actuator plays a critical role in transient shift simulations. It is particularly difficult to tune the actuator model when it is over-parameterized. Therefore, it is of great importance to develop a hydraulic actuator model that is easy to adjust while retaining sufficient complexity for replicating realistic transient behaviors. This paper describes a systematic approach for reducing the hydraulic actuator model into a piecewise 1st order representation based on piston movement.

Warpage is the distortion induced by inhomogeneous shrinkage during injection molding of plastic parts. Uncontrolled warpage will result in dimensional instability and bring a lot of challenges to the mold design and part assembly. Current commercial simulation software for injection molding cannot provide consistently accurate warpage prediction, especially for semi-crystalline thermoplastics. In this study, the root cause of inconsistency in warpage prediction has been investigated by using injection molded polypropylene plaques with a wide range of process conditions. The warpage of injection molded plaques are measured and compared to the numerical predictions from Moldex3D. The study shows that with considering cooling rate effect on crystallization kinetics and using of the improved material model for residual stress calculations, good agreements are obtained between experiment and simulation results.

Friction reduction in lubricated components through engine oil formulations has been investigated in the present work. Three different DI packages in combination with one friction modifier were blended in SAE 5 W-20 and SAE 0 W-16 viscosity grades. The friction performance of these oils was compared with GF-5 SAE 5 W-20 oil. A motored cranktrain assembly has been used to evaluate these, in which friction mean effective pressure (FMEP) as a function of engine speeds at different lubricant temperatures is measured. Results show that the choice of DI package plays a significant role in friction reduction. Results obtained from the mini-traction machine (MTM2) provide detailed information on traction coefficient in boundary, mixed and elastohydrodynamic (EHD) lubrication regimes. It has been shown that the results from the cranktrain rig are fairly consistent with those found in MTM2 tests for all the lubricants tested.

The crush strength of aluminum 5052-H38 honeycomb materials under combined compressive and shear loads are investigated here. The experimental results indicate that both the peak and crush strengths under combined compressive and shear loads are lower than those under pure compressive loads. A yield function is suggested for honeycomb materials under the combined loads based on a phenomenological plasticity theory. The microscopic crush mechanism under the combined loads is also investigated. A microscopic crush model based on the experimental observations is developed. The crush model includes the assumptions of the asymmetric location of horizontal plastic hinge line and the ruptures of aluminum cell walls so that the kinematic requirement can be satisfied. In the calculation of the crush strength, two correction factors due to non-associated plastic flow and different rupture modes are considered.

Pickup box drum drop test is critical in vehicle development to determine the impact strength of the floor panels. Physical hardware tests on prototypes have been used to assess whether the performance of the future pickup box meets design requirements. In order to reduce costs and shorten development cycle, CAE methodology was developed to accurately model the drum drop test. In this paper, a CAE procedure for modeling the drum drop test is proposed. Dynamic explicit finite element code LS-Dyna was used to simulate the non-linear impact process of a drum onto the box floor. The permanent plastic damages on the floor panel were recorded in both simulation and experiments. Very good correlation between the simulation results and the physical hardware tests was achieved. It indicates that the methodology developed is an effective tool in evaluating the performances of the pickup box floor panels.

Two finite element methodologies for simulating oil-canning tests on closure assemblies are presented. Reflecting the experimental conditions, the simulation methodologies assume load-controlled situations. One methodology uses an implicit finite-element code, namely ABAQUS®, and the other uses an explicit code, LS-DYNA®. It is shown that load-displacement behavior predicted by both the implicit and explicit codes agree well with experimental observations of oil-canning in a hood assembly. The small residual dent depth predictions are in line with experimental observations. The method using the implicit code, however, yields lower residual dent depth than that using the explicit code. Because the absolute values of the residual dent depths are small in the cases examined, more work is needed, using examples involving larger residual dent depth, to clearly distinguish between the two procedures.

Response surface methodologies (RSMs) have been proposed as surrogate models in vehicle design processes to gain insight and improve turnaround time for optimization and robust design. However, when studying the vehicle occupants during crash events, nonlinearities in responses, coupled with the relatively high dimensionality of vehicle design, can yield misleading results with little or no warning from the response surface algorithms. To ensure the accuracy and reliability of RSMs, fast and dependable error estimation procedures are essential for enlightening how well a response surface predicts highly nonlinear phenomena, given a limited number of model simulations. Such error estimation methods are also useful for providing guidance on how many simulation runs are needed for reliable RSM construction. In this paper, a fast cross validation error estimate procedure is first presented, applied to the multivariable adaptive regression spline (MARS) response surface method.

The objective of this paper is to develop a test capable of ranking lift-gates based on strain concentration levels reflected in fringe characteristics in the known stress/strain concentration and fracture vicinity. First, the system (lift gate glass, adhesive and appliqué) is chosen as test sample since the subsystem (local appliqué) does not exhibit the failure mode observed in the field test. Subsequently, it has been identified that the thermal component (rather than mechanical) is the predominant load by laser scanning vibrometry and confirmed via field test data. Next, digital shearography has been selected as the measurement and visualization tool of strain distribution due to its various advantages such as full field view and non-contact advantages. Finally, the test method has been applied to rank and optimize the structural configuration around appliqués' to reduce / eliminate failure.

In the developement process, the engineer is required to design, validate and deliver the components for manufacturing, in an as short as possible lead time. For that, the engineer may use some available tools to save not only time, but also cost. This work presents a zero prototype approach applyied to a plastic component, whose main accomplishment was the decreasing of lead time development due to the intensive use of virtual tools (CAD/CAE). As a result, the product was delivered in a short time, with no need of building physical prototypes, thus reducing development cost.

The use of plastics and elastomers, for interior and exterior automotive components, presents a risk of frictionally incompatible materials contacting each other, resulting in squeaks, ticks, chirps… Ford's NVH S&R Department, and MB Dynamics have developed a tester (Figures 1 and 2) that can measure friction, and sound, as a function of sliding velocity, normal load, surface roughness, and environmental factors that allows us to provide up-stream engineering information to Forward Model Design Engineers. When material pairs undergo sliding contact, friction forces can cause elastic deformation adjacent to the contacting surfaces. The elastic deformation is a mechanism for storing energy and sound is produced when the energy is released. The sound that we hear may be a squeak or squeal (multiple stick-slip) or a tick (single stick-slip).