Search Results

The physical 1-D model of a radial turbine consists of a set of gas ducts featuring total pressure and/or temperature changes and losses. Therefore, the wave propagation and filling/emptying plays a significant role if a turbine is subjected to unsteady gas flow. The results of unsteady turbine simulation using the basic modules of generalized 1-D manifold solver in GT Power are demonstrated. The turbine model calibration parameters can be identified by means of 1-D steady model used in optimization code loop. The examples of model results are compared to steady flow map predictions of turbine efficiency and engine pumping loop work. The model may be used for prediction of turbine data in out-of-design points as presented in the paper. The other important role of a model, however, is an accurate evaluation of turbine parameters from pressure and speed measurements at an engine in operation.

A previously developed CFD-based optimization tool is utilized to find optimal engine operating conditions with respect to fuel consumption and emissions. The optimization algorithm employed is based on the steepest descent method where an adaptive cost function is minimized along each line search using an effective backtracking strategy. The adaptive cost function is based on the penalty method, where the penalty coefficient is increased after every line search. The parameter space is normalized and, thus, the optimization occurs over the unit cube in higher-dimensional space. The application of this optimization tool is demonstrated for the Sulzer S20, a central-injection, non-road DI diesel engine. The optimization parameters are the start of injection of the two pulses of a split injection system, the duration of each pulse, the exhaust gas recirculation rate, the boost pressure and the compression ratio.

The aim of the current contribution is to develop a tool for the improvement of accuracy of turbocharger turbine simulation during matching of a turbocharger to an engine. The paper demonstrates the possibility of unsteady turbine simulation in pulsating flow caused by an internal combustion engine using the basic modules of generalized 1-D manifold solver with entities (pipes, channels) under centrifugal acceleration in general direction and under non-uniform angular speed, which has not yet been explored. The developed model extrapolates steady operation turbine maps by this way. It uses 1-D model parameters identified from steady flow experiments. Unlike the lumped-parameter standard models of turbocharger turbines, the model takes into account complete 1-D features of a turbine flow path including arbitrary shape of turbine impeller vanes.

Transient engine operations are modeled and simulated with a 1-D code (GT Power) using heat release and emission data computed by a 3-D CFD code (Kiva3). During each iteration step of a transient engine simulation, the 1-D code utilizes the 3-D data to interpolate the values for heat release and emissions. The 3-D CFD computations were performed for the compression and combustion stroke of strategically chosen engine operating points considering engine speed, torque and excess air. The 3-D inlet conditions were obtained from the 1-D code, which utilized 3-D heat release data from the previous 1-D unsteady computations. In most cases, only two different sets of 3-D input data are needed to interpolate the transient phase between two engine operating points. This keeps the computation time at a reasonable level. The results are demonstrated on the load response of a generator which is driven by a medium-speed diesel engine.

The new simulation tool consists of an iterative loop of a 3-D code in parallel to a 1-D code that is employed to simulate transient engine cycles. The 1-D code yields the basic pattern of initial and boundary conditions and the 3-D simulations at several typical engine operating points are used to crosscheck the performance as well as aid in the model calibration. A flexible regression model of the fuel burn rate and the associated ROHR has been developed in conjunction with the 3-D simulations using a combination of three added Vibe functions. The emissions at the end of the expansion stroke are also predicted. The parameters of the Vibe functions and emissions are found via nonlinear regression based on state parameters such as engine speed, relative A/F ratio, EGR/rest gas contents, injection timings, etc. Additional 3-D simulations that are made at specific engine operating points complement this compact burn rate parameter library.

The paper deals with investigation of flow characteristics of turbocharger turbine under real operating conditions on engine by means of combination of experimental data and advanced 1-D code for combustion engine simulation. Coupling simulations tools with the results of measurements provides the engineers with data which are difficult or impossible to measure. For instance by means of a three pressure analysis (TPA) applicable on engine cylinder the engineers can obtain burn rate, valve flow and residual gas compound from measured pressure traces in cylinder and at inlet and outlet ports. A method for turbocharger turbine on engine identification similar in principle to the three pressure analysis has been applied on radial turbine with variable geometry. A new computational module has been developed to allow identification of instantaneous flow and efficiency characteristics of the turbine.

The proposed paper deals with thermodynamic optimization of highly flexible ICE (variable compression ratio, intake/exhaust VVA) while comparing e-turbocharging concept with classical one. The e-turbocharging approach is based on idea that compressor/turbine has its own electric machine (motor/generator) and that additional electric energy can be supplied/attached from/to engine crank train. Hence it allows independent control of compressor/turbine. On the other hand, classical approach is based on a standard mechanical connection between turbine and compressor. The whole system (flexible engine + boost device) is optimized under steady operation – low load (BMEP of 4 bar), medium load (BMEP of 13 bar), high load (BMEP of 30, 25 and 18 bar) and maximum load are considered. Moreover, 3 combustion concepts are considered – classical SI and CI, and ideal RCCI. Sensitivity study of selected parameters is performed: e.g., efficiency of electric machine(s), HP exhaust manifold volume.

A quasi-dimensional dual fuel combustion model is proposed for a large 2-stroke marine engine. The introduced concept accounts for both diffusion combustion of the liquid pilot fuel and the flame front propagation throughout the gaseous premixed charge. For the pilot fuel case a common integral formulation defines the ignition delay whereas a time scale approach is incorporated for the combustion progress modeling. In order to capture spatial differences given by the scavenging process and the admission of the gaseous fuel, the cylinder volume is discretized into a number of zones. The laws of conservation are applied to calculate the thermodynamic conditions and the fuel concentration distribution. Subsequently, the ignition delay of the gaseous fuel-air mixture is determined by the use of tabulated kinetics and the ensuing oxidation is described by a flame velocity correlation.

The paper proposes the way of using scavenging curves, i.e., dependence of residual gas fraction in exhaust port or valve on residual fraction in a cylinder, found by CFD simulations. In the general case, exhaust gas recirculation outside of a cylinder (EGR) or internal gas recirculation caused by variable values of burned gas backflow to inlet system may influence in-cylinder residual gas fraction. These deviations may take place during engine optimization, done by 1D models. The determination of scavenging curves via 3D CFD simulations is a time consuming process, which cannot be repeated for every 1D case.

A Large-Eddy-Simulation (LES) approach is applied to the calculation of multiple SI-engine cycles in order to study the causes of cycle-to-cycle combustion variations. The single-cylinder research engine adopted in the present study is equipped with direct fuel-injection and variable valve timing for both the intake and exhaust side. Operating conditions representing cases with considerably different scatter of the in-cylinder pressure traces are selected to investigate the causes of the cycle-to-cycle combustion variations. In the simulation the engine is represented by a coupled 1D/3D-CFD model, with the combustion chamber and the intake/exhaust ports modeled in 3D-CFD, and the intake/exhaust pipework set-up adopting a 1D-CFD approach. The adopted LES flow model is based upon the well-established Smagorinsky approach. Simulation of the fuel spray propagation process is based upon the discrete droplet model.

The objective of this study is the development of a computationally efficient CFD-based tool for finding optimal engine operating conditions with respect to fuel consumption and emissions. The optimization algorithm employed is based on the steepest descent method where an adaptive cost function is minimized along each line search using an effective backtracking strategy. The adaptive cost function is based on the penalty method, where the penalty coefficient is increased after every line search. The parameter space is normalized and, thus, the optimization occurs over the unit cube in higher-dimensional space. The application of this optimization tool is demonstrated for the Sulzer S20, a central-injection, non-road DI diesel engine. The optimization parameters are the start of injection of the two pulses, the duration of each pulse, the duration of the dwell, the exhaust gas recirculation rate and the boost pressure.

The paper deals with the investigation of turbocharger optimization procedures using amended 1-D simulation tools. The proposed method uses scaled flow rate/effficiency maps for different sizes of a radial turbine together with a fictitious compressor map. The compressor pressure ratio/efficiency map depends on compressor circumference velocity only and predicts the both compressor specific power and achievable efficiency. At the first stage of optimization, it avoids the problems of reaching choking/surge limits. It enables the designer to find a suitable turbine type under realistic unsteady conditions (pressure pulses in exhaust manifold) concerning turbine flow area. Once the optimization of turbine/compressor impeller diameters is finished, the specific compressor map is selected. The proposed method provides the fast way to the best solution even for the case of a VGT turbine. Additional features have been developed for the representation of scaled turbine and compressor maps.

In this article the development of a combustion system with a fuel-scavenged pre-chamber is described. Such a system is commonly used in large-bore engines operated with extremely lean mixtures. The authors implemented the scavenged pre-chamber into a light duty truck-size engine with a bore of 102 mm. The lean burn strategy is intended to achieve very low nitrogen oxide (NOx) emissions at low load. At full load a stoichiometric mixture strategy is applied to achieve sufficient power density while simultaneously enabling the use of a relatively simple three-way catalytic converter for exhaust gas aftertreatment. This work outlines the pre-chamber design features and introduces the results of an experimental investigation of the effect of pre-chamber ignition on a single cylinder testing engine.

The article describes the utilization of the map-less approach in simulation of single and twin scroll radial turbines. The conventional steady flow maps are not used. An unsteady 1-D model of a twin scroll turbine includes scrolls, mixing of flows upstream of the impeller, turbine wheel, leakages and outlet pipe. Developed physical turbine model was calibrated with data from experiments at specific steady flow turbocharger test bed with open loop, which enables to achieve arbitrary level of an impeller admission via throttling in separate sections. A selected twin scroll turbine was tested under full, partial flow admission of an impeller and extreme partial admission with closed section. The required number of operating points is relatively low compared with conventional steady flow maps, when the maps have to be generated for each level of an impeller admission. The calibration process of the full 1-D turbine model is described.

The mass and overall dimensions of massively downsized engines for very high bmep (up to 35 bar) cannot be estimated by scaling of designs already available. Simulation methods coupling different levels of method profoundness, as 1-D methods, e.g., GT Suite/GT Power with in-house codes for engine mechanical efficiency assessment and preliminary design of boosting devices (a virtual compressor and a turbine), were used together with optimization codes based on genetic algorithms. Simultaneously, the impact of optimum cycle on cranktrain components dimensions (especially cylinder bore spacing), mass and inertia force loads were estimated since the results were systematically stored and analyzed in Design Assistance System DASY, developed by the authors for purposes of early-stage conceptual design. General thermodynamic cycles were defined by limiting parameters (bmep, burning duration, engine speed and turbocharger efficiency only).