Search Results

Historically, the long development time required to produce a new automobile has meant that the electronics in that vehicle might lag the state-of-the-art by several years. For traditional vehicle electronics, this was certainly an appropriate delay, ensuring through extensive testing and qualification that the quality and reliability of the electronic systems met rigorous standards. However, with the growing consumer-oriented electronics content in today's vehicles, it is becoming more difficult for the automotive manufacturers to meet consumers' expectations with older technology. Couple this with the fast-paced consumer product cycle, typically nine to eighteen and the result is increasing pressure on the vehicle manufacturers from after-market electronics suppliers, who can update their product lines as fast as the component manufacturers can produce new models.

This paper describes the results of an ongoing project in the GM Motorsports Safety Technology Research Program to investigate Indianapolis-type (Indy car) race car crashes using an on-board impact recorder as the primary data collection tool. The paper discusses the development of specifications for the impact-recording device, the selection of the specific recorder and its implementation on a routine basis in Indy car racing. The results from incidents that produced significant data (crashes with peak decelerations above 20 G) during the racing seasons from 1993 through the first half of 1998 are summarized. The focus on Indy car crashes has proven to provide an almost laboratory-like setting due to the similarity of the cars and to the relative simplicity of the crashes (predominantly planar crashes involving single car impacts against well-defined impact surfaces).

In order to engineer Squeak & Rattle (S&R) free vehicles it is essential to develop an objective measurement method to compare and correlate with customer satisfaction and subjective S&R assessments. Three methods for exciting S&Rs -type surfaces. Excitation methods evaluated were road tests over S&R surfaces, road simulators, and direct body excitation (DBE). The principle of DBE involves using electromagnetic shakers to induce controlled, road-measured vibration into the body, bypassing the tire patch and suspension. DBE is a promising technology for making objective measurements because it is extremely quiet (test equipment noise does not mask S&Rs), while meeting other project goals. While DBE is limited in exposing S&Rs caused by body twist and suspension noises, advantages include higher frequency energy owing to electro-dynamic shakers, continuous random excitation, lower capital cost, mobility, and safety.

We investigate and analyze the concept of “shared redundancy” and its application to the design of architectures that integrate multiple safety/mission critical functions or subsystems. The analysis is based on considering different design alternatives with varying levels of physical redundancy of the components constituting the functions or subsystems. Under a set of assumptions, we show that the overall system reliability and availability in a shared redundancy based architecture can be improved without increasing the levels of physical redundancy for the components employed at the subsystem level. However, such an improvement will be limited by the component(s) with the minimal level of redundancy.

Extending engine-oil-change intervals is of interest from the standpoint of reducing used oil disposal and reducing time and expense of maintenance. However, the oil must be changed before serious oil degradation and engine damage occur. Three variables which influence oil degradation were chosen for investigation: base oil composition (synthetic oil versus mineral oil), trip length (short trips versus long trips), and driving schedule (degrading an oil during a given type of service, then changing to another type of service without an intervening oil change). Analysis of oil samples taken throughout the testing program indicated that type of service (freeway compared to short trip) influenced oil degradation to a greater extent than oil type. That is, API SG-quality synthetic oil in short-trip service degraded faster than borderline SG-quality mineral oil in long-trip service.

A design synthesis approach is used to design and analyze a Resin-Transfer-Molded (RTM) composite floorpan to meet the product requirements and assess the structural performance. The design envelope is based on packaging constraints representative of a production vehicle to ensure a feasible design intent. Finite element analysis of the composite design is used to guide the design and integrate all of the product performance requirements to achieve a feasible design concept. Issues discussed include the design and analysis, design features, composite material tailoring, prototype fabrication, vehicle build, and product validation. Stiffness, strength and durability tests were performed on the floorpan and the fully trimmed vehicle, and all requirements were met.

The rear cross-car stiffener subsystem is generally located at the underside of the rear compartment pan of a car body and connects the two rear longitudinal rails or rear rockers. The primary purpose of this subsystem is to maintain structural integrity as well as fuel system integrity in a rear angle impact or dynamic side impact collision. To evaluate the effect of this subsystem on lateral crashworthiness in a high speed angle impact, a finite element model consisting of the cross-car bar, a portion of rear compartment pan and both rear rails was developed and analyzed with the DYNA3D crashworthiness simulation software. Thus, the cross-car stiffener subsystem design including the welding pattern was finalized and the acceptable design was successfully implemented in the vehicle. Subsequently drop silo tests were carried out to further verify the design and to improve the manufacturing process.

A mathematical model was developed to evaluate design options for control of road noise transmission into the interior of a passenger car. Both air-borne and structure-borne road noise over the frequency range of 200-5000 Hz was able to be considered using the Statistical Energy Analysis (SEA) method. Acoustic and vibration measurements conducted on a laboratory rolling road were used to represent the tire noise “source” functions. The SEA model was correlated to in car sound pressure level measurements to within 2-4 db accuracy, and showed that airborne noise dominated structure-borne noise sources above 400 Hz. The effectiveness of different noise control treatments was simulated and in some cases evaluated with tests.

Side impact pendulum tests were conducted on Eurosid I and Biosid to assess the biofidelity of the thorax, abdomen and pelvis, and determine injury tolerance levels. Each body region was impacted at 4.5, 6.7, and 9.4 m/s using test conditions which duplicate cadaver impacts with a 15 cm flat-circular 23.4 kg rigid mass. The cadaver database establishes human response and injury risk assessment in side impact. Both dummies showed better biofidelity when compared to the lowest-speed cadaver response corridor. At higher speeds, peak force was substantially higher. The average peak contact force was 1.56 times greater in Biosid and 2.19 times greater in Eurosid 1 than the average cadaver response. The Eurosid I abdomen had the most dissimilar response and lacks biofidelity. Overall, Biosid has better biofidelity than Eurosid I with an average 21% lower peak load and a closer match to the duration of cadaver impact responses for the three body regions.

This paper describes a numerical simulation technique applicable to the FMVSS 214 side impact test through the use of the finite element method (FEM) technology. The paper outlines the development of the side impact dummy (SID), moving deformable barrier (MDB) and the test vehicle FEM models, as well as the development of new advanced constitutive models of materials and algorithms in LS-DYNA3D which are related to the topic. Presented in the paper are some initial simulation problems which were encountered and solved, as well as the correlation of the simulation data to the physical test.

As the driving population ages, there is a need to understand the accident patterns of older drivers. Previous research has shown that side impact collisions, usually at an intersection, are a serious problem for the older driver in terms of injury outcome. This study compares the frequency of side impact, intersection collisions of different driver age groups using state and national police-reported accident data as well as an in-depth analysis of cases from a fatal accident study. All data reveal that the frequency of intersection crashes increases with driver age. The state and national data show that older drivers have an increase frequency of intersection crashes involving vehicles crossing paths prior to the collision compared to their involvement in all crash types. When taking into account traffic control devices at an intersection, older drivers have the greatest involvement of multiple vehicle crashes at a signed intersection.

Fatal crash circumstances for 48 belted female drivers were studied in-depth and compared to those of 83 belted male drivers in a similar population of vehicles. Women had a higher incidence of crashes on slippery roads, during lane changes and passing maneuvers than men who had a higher rate of aggressive driving and speed related crashes (χ2 = 10.47, p < 0.001). Driver-side damage was significantly more frequent in female than male crashes (χ2 = 5.74, p < 0.025) and women had a higher fraction of side impacts (45.9% v 31.4%) and crashes during daylight (87.0% v 72.3%, χ2 = 3.65, p < 0.05) than men. Women also had a higher fraction of potentially avoidable crashes than men (57.5% v 39.0%) and a lower involvement related to aggressive driving (10.6% v 25.6%). These differences were statistically significant (χ2 = 5.41, p < 0.025).

Side impact dummy (SID) is a human-like test device used in the National Highway Transportation Safety Administration (NHTSA) mandated side impact test of vehicles sold in the USA. A finite element model of SID has been developed at GM as a part of a project to simulate the side impact test. The objective is to better predict physical test results by replacing traditional rigid-body lumped parameter models with a finite element model. The project included, besides mesh generation, the development of new LS-DYNA3D constitutive models for rubber and foam-like materials, and enhancements of contact interface and other algorithms. This paper describes the GM SID finite element model and its performance in side impact test simulations.

The Cadillac Electronic Climate Control heating and air conditioning system provides automatic control of the passenger compartment temperature. It utilizes a microcomputer to control the operation of electrical, mechanical and vacuum components that regulate the amount and temperature of air delivered into the car to maintain the “customer set” comfort level. The first step in the evolution of this new system was to define the performance requirements. With this established, the system was then designed, tested and developed in the laboratory and on the road until this desired performance was achieved.

TFC/IW, total fuel consumption divided by inertia (test) weight is a useful concept in analyzing the total or composite fuel economy generated in thousands of tests using the carbon balance technique in EPA Federal Test Procedure and Highway Driving Cycle. TFC/IW is a measure of drive train efficiency that requires no additional complicating assumptions. It is applicable to one test or a fleet representing many tests.

IN 1951 Chrysler Corp. began working on a new torsion suspension. In this paper the authors describe details of the development and design of the suspension, now available on 1957 cars. The authors claim the Torsion-Aire suspension has the following advantages: reduced highspeed float, boulevard harshness, impact harshness, road noise, body roll, nose dive, and acceleration squat; better directional stability and cornering ability; fewer lubrication points; and a better balanced ride. The main feature of the front suspension is the use of torsion bars. One of the principal advantages of torsion bars is their weight: 10 lb as compared to 15.8 lb for a 1956 production coil spring.

The paper outlines testing, development, and operation of the first production four-wheel slip control system for passenger cars in the United States. The Chrysler Corp. calls the system “Sure-Brake,” but it is more generally known as “anti-skid.” The first portion of the paper deals with considerations that led Chrysler into the Sure-Brake system, the philosophy behind the system, and a detailed explanation of its operation. The second portion deals with the development and testing of the system, leading to its release as an option on the 1971 Imperial. The testing program introduced a new dimension to brake engineering. Before the advent of wheel slip control systems, many thousands of brake tests were conducted but were always terminated at the point of skid. These tests were also conducted mainly on black top or concrete roads. For the first time, thousands of stops were made at maximum deceleration on every available surface.

The search for improvements in occupant protection under vehicle impact is hampered by a real lack of reliable biomechanical data. To help fill this void, General Motors has initiated joint research with independent researchers such as the School of Medicine, U. C. L. A. – in this case to study localized head and facial trauma — and has developed such unique laboratory tools as “Tramasaf,” a human-simulating headform, and “MetNet,” a pressure-sensitive metal foam. Research applied directly to product design also has culminated in developments such as the Side-Guard Beam for side impact protection.

THE GRADEABILITY formula can be used as the basic means for rating a truck transmission. By correlating the gradeabilities in the various gear ratios with a highway requirement probability curve, the per cent of time in each ratio can be obtained. The required hours of gear life for each ratio are then determined, and compared with the available gear life in the ratios. This procedure gives a detailed analysis of a transmission rating for one vehicle specification at a specified mileage between overhauls. A limitation of the system is that it cannot be applied quickly to various vehicle specifications. The paper outlines the method for constructing a nomogram to overcome this.*