Search Results

An efficient development environments such as Software-in-the-Loop Simulation (SILS) and Rapid Control Prototyping (RCP) have been widely used to reduce the development time and cost of real-time ECUs. However, conventional SILS does not consider temporal behaviors caused by computation time, task scheduling, network-induced delays, and so on. As a result, the control performance of ECU is likely to be degraded after implementation. To overcome this problem, SILS/RCP which considers the temporal behaviors was suggested in the previous research. In this study, we validated the proposed SILS/RCP environments which are used to design an Electronic Stability Control (ESC) system which is one of the hard real-time control systems. The proposed SILS/RCP environments make it possible to realize ECUs in the early design phase by considering temporal behaviors.

FlexRay is a deterministic and fault-tolerant in-vehicle network(IVN) protocol. It is expected to become a practical standard for automotive communication systems. According to the FlexRay protocol specifications, there are about 60 configurable parameters which should be determined in the design phases. The parameters increase the complexities of FlexRay-based control system development. In this study, we are suggesting a formal design process for FlexRay-based control systems, which is focused on network parameter optimization. We introduce design phases from functional system models to implementations. These phases present formal ways for task allocation, node assignment, network configuration, and implementations. In the network configuration phase, two FlexRay core parameters are selected to optimize network design. Optimal methods of the core parameters provide concise guide lines for optimal communication cycle length and optimal static slot length.

A fault detection method with parity equations is proposed in this paper. Due to low cost implementation, the velocity of a motor is not measurable in EPB systems. Therefore, residuals are not reliable with a low resolution encoder to estimate the motor velocity. In this paper, we propose a fault detection method with sensorless estimation using current ripples. The method estimates position and velocity of the motor by detecting periodical oscillations of the armature current caused by rotor slots. This method could estimate position and velocity of the motor with less computational effort than a state observer. Moreover, the method is less sensitive to motor parameters than model-based estimation methods. The effectiveness of this method is validated with experimental data. The simulation results show that various faults have their own residual patterns. Therefore, we could detect the fault by monitoring the residual signals.

Electro-hydraulic brake (EHB) provides improved braking and stability functions such as ABS, TCS, ESC, EBD, etc. It also removes complex mechanical parts for freedom of design, improves maintenance requirements and reduces unit weight. But, the EHB should be at least as reliable as the conventional hydraulic brake system. In this paper, the model-based fault diagnosis system is developed to monitor the brake status using the analytical redundancy method. The performance of the model-based fault diagnosis system is verified in simulations and demonstrates the effectiveness of the proposed system in various faulty cases.

Electromechanical relays that are coupled with fuses have been used for controlling electrical loads in vehicles. In the past decade, semiconductor power switches have been developed for overcoming the physical limits of relays and fuses. Semiconductor power switches can not only replace relays and fuses but can also improve a system's reliability and efficiency. In this study, we introduce the Smart Automotive Switch (SAS), which is a smart high side power switch of Fairchild Korea semiconductor. Functional capabilities, such as power switching, protection and self-diagnosis of SASs are presented in case studies involving, for example, headlights, glow plugs, and fuel pump control systems. Through these experimental studies, the suitability of SASs is validated for designing improved automotive electronic control systems.

This paper presents a preliminary study of a sampling period decision for robust control of a distributed control system based on an in-vehicle network with three types of data (real-time synchronous data, real-time asynchronous data, and nonreal-time asynchronous data). The architecture of automotive systems is currently changing from a number of standalone electronic control units (ECUs) to a functionally integrated distributed system which is linked by a network. The control performance of the integrated networked control system can be changed by the characteristics of time delays among the application ECUs. A basic parameter for a scheduling method of the networked control systems, a maximum allowable delay bound is used, which guarantees stability of the networked control system, and it is derived from the characteristics of the given plant using presented theorems.

This paper presents the Matlab/Simulink-based Software-in-the-Loop Simulation (SILS) tool which is the co-simulator for temporal and functional simulations of control systems. The temporal behavior of a control system is mainly dependent on the implemented software and hardware such as the real-time operating system, target CPU and communication protocol. In this research, the SILS components with temporal attributes are specified as tasks, task executions, real-time schedulers, and real-time networks. Methods for realizing these components in graphical block representations are investigated with Matlab/Simulink, which is the most commonly used tool for designing and simulating control algorithms in control engineering. These components are modeled in graphical blocks of Matlab/Simulink.

Human drivers navigate by continuously predicting the intent of road users and interacting with them. For safe autonomous driving, research about predicting future trajectory of vehicles and motion planning based on these predictions has drawn attention in recent years. Most of these studies, however, did not take into account driver’s intentions or any interdependence with other vehicles. In order to drive safely in real complex driving situations, it is essential to plan a path based on other driver’s intentions and simultaneously to estimate the intentions of other road user with different characteristics as human drivers do. We aim to tackle the above challenges on highway merge scenario where the intention of other road users should be understood. In this study, we propose an intention aware motion planning method using finite state machine and model predictive control without any vehicle-to-vehicle (V2V) or vehicle-to-infrastructure (V2I) communications.