Refine Your Search

Topic

Author

Affiliation

Search Results

Video

Introduction of New Concept U*sum for Evaluation of Weight-Efficient Structure

2011-11-01
A new index for evaluating load path dispersion is proposed, using a structural load path analysis method based on the concept of U* , which expresses the connection strength between a load point and an arbitrary point within the structure enables the evaluation of the load path dispersion within the structure by statistical means such as histograms and standard deviations. Presenter Tadashi Naito, Honda R&D Co., Ltd.
Technical Paper

Computer simulation process for pedestrian protection structures

2000-06-12
2000-05-0222
Research into pedestrian protection has been carried out since the 1960s, in recent years there have been proposals in Europe to legislate requirements in this area and therefore the research is becoming more focused. In the draft regulation, impactor tests have been proposed as a method for evaluating the impact caused by vehicles'' body for pedestrians. This paper introduces impactor model and actual vehicle analysis as a means for simulating impactor testing. Three types of impactors for vehicle tests are presented. It is necessary that the models are first matched with the results of the calibration tests, then matched with the results of the tests on actual vehicles.
Technical Paper

Modification of Vehicle Handling Performance by Four-Wheel Steering System

1985-01-01
856039
At past ESV conferences, we have reported on a series of studies on how the driver's control performance is affected by vehicle steering response. These studies showed that a four-wheel steering system can reduce the delay in lateral acceleration response to steering action, which may result in better control performance of the driver. The present report examines the handling performance of an experimental vehicle fitted with a four-wheel steering system under a wider range of operating conditions. The studies were conducted using mathematical models and simulation of the driver-vehicle system, plus road tests. The findings indicate that the four-wheel steering system may provide better vehicle handling performance than a conventional two-wheel steering system. A vehicle incorporating this steering system may exhibit improved accident avoidance capabilities.
Technical Paper

Management System for Continuously Variable Valve Lift Gasoline Engine

2007-04-16
2007-01-1200
A continuously variable valve lift gasoline engine can improve fuel consumption by reducing pumping loss and increase maximum torque by optimizing valve lift and cam phase according to engine speed. In this research, a new control system to simultaneously ensure good driveability and low emissions was developed for this low fuel consumption, high power engine. New suction air management through a master-slave control made it possible to achieve low fuel consumption and good driveability. To regulate the idle speed, a new controller featuring a two-degree-of-freedom sliding-mode algorithm with cooperative control was designed. This controller can improve the stability of idle speed and achieve the idle operation with a lower engine speed. To reduce emissions during cold start condition, an ignition timing control was developed that combine I-P control with a sliding mode control algorithm.
Technical Paper

Liquid Phase Thermometry of Common Rail Diesel Sprays Impinging on a Heated Wall

2007-07-23
2007-01-1891
An experimental study was carried out on visualization of liquid phase temperature distributions in high-pressure diesel sprays impinging on a heated wall. Naphthalene/TMPD-exciplex fluorescence method and pyrene-excimer fluorescence method were utilized for the thermometry. The sprays were injected into a high-pressure and high-temperature gaseous environment. The nozzle hole diameter was 0.100 mm or 0.139 mm. The results showed that cool pockets were formed at the tip and in the impinging part of the sprays. The spray for the nozzle with 0.100 mm hole was heated up faster near the nozzle than for the nozzle with 0.139 mm hole.
Journal Article

Design Optimization of Interior Permanent Magnet Synchronous Motors for HEV & EV

2010-04-12
2010-01-1252
This paper proposes a new motor design procedure for reducing motor loss in hybrid vehicles (HEV) and electric vehicles (EV). To find an optimum design in a short time, a non-linear magnetic circuit model was developed for interior permanent magnet synchronous motors (IPMSM). Speed-torque curves and motor losses were calculated based on this model. Combined with Energy Management Simulation, this model makes it possible to find an optimum motor design with minimum loss.
Journal Article

Introduction of New Concept U*sum for Evaluation of Weight-Efficient Structure

2011-04-12
2011-01-0061
A new index U* for evaluating load path dispersion is proposed, using a structural load path analysis method based on the concept of U*, which expresses the connection strength between a load point and an arbitrary point within the structure. U* enables the evaluation of the load path dispersion within the structure by statistical means such as histograms and standard deviations. Different loading conditions are applied to a body structure, and the similarity of the U* distributions is evaluated using the direction cosine and U* 2-dimensional correlation diagrams. It is shown as a result that body structures can be macroscopically grasped by using the U* distribution rather than using the stress distribution. In addition, as an example, the U* distribution of torsion loading condition is shown to comprehensively include characteristics of the U* distribution of other loading conditions.
Technical Paper

Study of Effect of CVT Pulleys on Strength and Transmission Efficiency of Metal Pushing V-belts

2011-04-12
2011-01-1426
In designing CVT pulleys, the effect of the fit clearance of the movable pulleys and their stiffness on the transmission efficiency and strength of the metal pushing V-belt is not necessarily clear. The research discussed in this paper introduced a pulley model that defined the pulleys as elastic bodies to a previously developed technology for the prediction of the transmission efficiency of the belts. As a result, it was found that when the fit clearance is reduced, the transmission efficiency of the belt is increased, and the amplitude of stress on the innermost rings and the element neck section is reduced. In addition, it was found that if pulley stiffness was reduced transmission efficiency was also reduced, and the amplitude of stress on the element neck section increased. This indicated that the fit clearance and the pulley stiffness changed the degree of deflection of the pulleys in the axial direction.
Technical Paper

Prediction of Transient Body Deformation During Handling Maneuvers

2010-04-12
2010-01-0945
A multi-body dynamics model that considers elastic deformation of the body was formulated in order to predict transient body deformation, a factor that affects handling. A comparative analysis with body deformation during handling maneuvers identified using a modal forced response method was conducted, and a good correlation was obtained between vehicle dynamic performance, transient body deformation, and the body modal contribution factor.
Technical Paper

The Validity of EPS Control System Development using HILS

2010-04-12
2010-01-0008
In recent years, the increased use of electric power steering in vehicles has increased the importance of issues such as making systems more compact and lightweight, and dealing with increased development man-hours. To increase development efficiency, the use of a “Hardware in the loop simulator” (HILS) is being tested to shift from the previous development method that relied on a driver's subjective evaluation in an actual vehicle test to bench-test development. Using HILS enables tasks such as specification studies, performance forecasts, issue identification and countermeasure proposals to be performed at an early stage of development even when there is no prototype vehicle. This report describes a case study of using HILS to solve the issues of reducing the load by adjusting the geometric specifications around the kingpin and eliminating the tradeoff by adding a new EPS control algorithm in order to make the electric power steering (EPS) more compact and lightweight.
Journal Article

Prediction of Fatigue Strength of Motorcycle Exhaust System Considering Vibrating and Thermal Stresses

2015-11-17
2015-32-0739
A method applicable in the design stage to predict fatigue strength of a motorcycle exhaust system was developed. In this prediction method, a vibrating stress, thermal stresses, stresses resulting from the assembling of the exhaust system components and a deterioration of fatigue strength of materials originated from high temperature were simultaneously taken into account. For the prediction of the vibrating stress, flexible multibody dynamics was applied to get modeling accuracy for vibration characteristics of the entire motorcycle and the exciting force delivered from engine vibrations. The thermal conduction analysis and the thermal deformation analysis based on finite element method (FEM) were applied for the prediction of thermal stresses in the exhaust system components. The temperature distribution on the surfaces of the exhaust system components is required for calculations of the thermal stresses.
Journal Article

Incoming Wave Estimation Characteristics by MUSIC Method Using a Virtual Array Antenna in Urban Reception Conditions

2016-04-05
2016-01-0077
We developed “Two-Stage Method” that makes it possible to evaluate the automotive suitability of FM receivers by generating a virtual radio wave environment on a PC. The major technological challenge for the Two-Stage Method was reproducing an actual radio wave environment on PC. It was necessary to estimate the characteristics of the FM radio wave environment in tests using the Multiple Signal Classification (MUSIC) method. However, when the MUSIC method is applied to FM reception, restrictions in factors including the number of array antenna elements and the occupied bandwidth result in issues of separation performance in relation to multipath waves in urban environments. We therefore developed a MUSIC Method using a virtual array antenna, making it possible to create combinations of numbers of array and sub-array elements as desired, thus boosting multipath wave separation performance. This development was reported at the 2015 SAE World Congress.
Journal Article

Development and Application of FM Multipath Distortion Rate Measurement System Using a Fading Emulator Based on Two-Stage Method

2016-04-05
2016-01-0082
The suitability of FM radio receivers for automobiles has conventionally been rated by evaluating reception characteristics for broadcast waves in repeated driving tests in specific test environments. The evaluation of sound quality has relied on the auditory judgment due to difficulties to conduct quantitative evaluations by experiments. Thus the method had issues in terms of the reproducibility and objectivity of the evaluations. To address these issues, a two-stage method generating a virtual radio wave environment on a PC was developed. The research further defined the multipath distortion rate, MDr, as an index for the sound quality evaluation of FM receivers, and the findings concerning the suitability of the evaluation of FM terminals for automobiles were reported at the 2015 SAE World Congress.
Journal Article

Positioning Simulation Using a 3D Map and Verification of Positional Estimation Accuracy in Urban Areas Using Actual Measurement

2016-04-05
2016-01-0083
Positional accuracy of GPS measurement has been based on simulation and actual measurement due to the difficulty of conducting 24-hour actual running tests. However, the conventional measurement is only based on brief evaluation; hence variability of positional accuracy which varies depending on measurement time and location had been an issue. Thus, it is significant to show the validity by the estimation of positional accuracy, and actual measurement using of lengthy simulation. In this study, actual measurement data in an urban area was obtained for long hours, and a simulation using 3D maps was implemented. A high precision positional measurement system was equipped on a vehicle in order to collect actual measurements and positional data at each measurement time. The data obtained by the measurement system was used as the reference coordinate for both the simulation and the actual measurements.
Technical Paper

Robust Design on Adhesive Material and Bonding Process for Automotive Battery Pack

2019-04-02
2019-01-0160
Adhesive bonding is a key technology for the lighter weight of battery pack trays using aluminum material. A robust design method of adhesive bonding with the required strength for battery pack structure after degradation was developed to minimize variability of strength under various noise conditions. The parameter design based on Taguchi methods determined the optimum adhesive condition of the bonding process. To guarantee strength after degradation, it is essential to select a robust adhesive material and to minimize the strength variation derived from the adhesive material. The functional evaluation, which includes experimental design method, determined adhesive material with the minimum strength variation among material candidates. Then, robustness of the adhesive material itself has been evaluated as the result of collaboration with the adhesive material supplier. This analysis was able to regulate the compound ratio of raw materials without reducing the adhesive strength.
Technical Paper

Atomization in High-Pressure Die Casting - Step 2 Simulation of Atomized Flow of Molten Aluminum by LES-VOF Method

2018-04-03
2018-01-1393
The atomization of molten aluminum when injected during high-pressure die casting is analyzed to determine its effect in enhancing the strength of the product being cast. In the previously reported first step of this study, molten aluminum was injected into open space and its atomization was observed photographically. Now in the second step of the study, a simulation is conducted to determine how the molten aluminum becomes atomized at the injection nozzle (gate) and how this atomized material flows and fills the cavity. A new simulation method is developed based on large-eddy simulation coupled with the volume-of-fluid method. The simulation system is verified by comparing its output with photographs taken in the first step of the study. Simulations are then conducted using an approximation of a real cavity to visualize how it is filled by the atomized molten aluminum.
Technical Paper

Research of Atomization Phenomena in HPDC-Step 1 Feature of Gas Porosity Dispersion and Photography of Atomized Flow

2018-04-03
2018-01-1392
In recent years, studies have been conducted on the relationship between the J factor, which indicates flow of molten aluminum at the time of injection, and the quality of HPDC products. The flow of molten metal at a high J factor is referred to as “Atomized Flow.” The authors and others conducted studies on the relationship between the J factor and the strength of HPDC products. An area exceeding 300MPa was found in the product produced at a high J factor corresponding to the “Atomized Flow.” The defect was less in the above-mentioned position because the gas porosity was finely dispersed. Considering that the fine dispersion of gas porosity is related to the “Atomized Flow”, pictures were taken to analyze “Atomized Flow.” The molten aluminum was ejected into an open space at a high speed and the splashed conditions were photographed. From the images taken by the pulse laser permeation, the conditions of microscopic atomized flow were observed precisely.
Technical Paper

Dynamic Simulation Software for Prediction of Hydrogen Temperature and Pressure during Fueling Process

2018-04-03
2018-01-1304
In this study, in order to relax the pre-cooling regulations at hydrogen fueling stations, we develop a software algorithm to simulate an actual hydrogen fueling process to Fuel Cell Vehicle (FCV) tanks. The simulation model in the software consists of the same filling equipment found at an actual hydrogen fueling station. Additionally, the same supply conditions (pre-cooling temperature, pressure and mass flow rate) as at a hydrogen fueling station were set to the simulation model. Based on the supply conditions, the software simulates the temperature and pressure of hydrogen in each part of filling equipment. In order to verify the accuracy of the software, we compare the temperature and pressure simulated at each stage of the filling process with experimental data. We show that by using the software it is possible to accurately calculate the hydrogen temperature and pressure at each point during the fueling process.
Technical Paper

Acceleration of Iterative Vibration Analysis for Form Changes in Large Degrees-of-Freedom Engine Model

2018-04-03
2018-01-1290
Operational analysis of automotive engines using flexible multi-body dynamics is increasingly important from the viewpoint of multi-objective optimization as it can predict not only vibration, but also stress and friction at the same time. Still, the finite element (FE) models used in this analysis have large degrees-of-freedom, so iterative calculation takes a lot of time when there is form change. This research therefore describes a technique that applies a modal differential substructure method (a technique that reduces the degrees of freedom in a FE model) that can simulate form changes in FE models by changing modal mass and modal stiffness in reduced models. By using this method, non-parametric form change in FE model can be parametrically simulated, so it is possible to speed up repeated vibration calculations. In the proposed method, FE model is finely divided for each form change design area, and a reduced model of that divided structure is created.
Technical Paper

Life Estimation of Rolling Bearings Based on the Colors on Sliding Surfaces

2019-04-02
2019-01-0180
It is experimentally known that the surface color of bearing balls gradually becomes brown during long term operation of the bearings under appropriate lubrication conditions. That exhibits the possibility of an estimation method for residual life of ball bearings without any abnormal wear on the surfaces by precise color measurements. Therefore, we examined what set colors on bearing balls by surface observation using scanning electron microscopy and subsurface analysis using transmission electron microscopy. Results showed that an amorphous carbon layer had gradually covered ball surfaces during operation of the bearings. The layer not only changed ball color but also made overall ball shapes closer to a complete sphere. The report also introduces a uniquely developed color analyzer which enabled color measurements on metallic surfaces, such as the above-mentioned balls.
X