Refine Your Search

Topic

Author

Affiliation

Search Results

Technical Paper

Development of Programmed-Fuel Injection for Two-Stroke Cycle Racer Engine

1991-11-01
911224
An electronically controlled fuel injection system for controlling the air/fuel (A/F) ratio has been looked forward as a means for improving drivability, output characteristics, and fuel consumption of two-stroke cycle motorcycle racer engines. However, actual installation of such a system on a high output two-stroke cycle engine (which utilizes exhaust gas pressure pulsation effects) has been considered difficult for the following reasons. Fluctuation in the delivery ratio (L) during firing and misfiring becomes great due to effects from the exhaust pipe. Applying the control method used for conventional four-stroke cycle engines (by which the delivery ratio (L) is measured) would necessitate a large and heavy system. The authors have eliminated such problems by developing an electronically controlled fuel injection system, the PGM-FI (Programmed-Fuel Injection) system, which employs basic intake air flow data according to engine speed (NE) and throttle opening (θTH).
Technical Paper

Improving Fuel Economy in Motorcycles Using One-Way Clutch

1989-11-01
891352
The one-way clutch mechanism seen on bicycles, etc. greatly ease the load of riders at times of coasting or descending downhill. Their use on motor vehicles are restricted to some automatic drive four-wheeled vehicles with torque converters. There are neither any example of mass-produced motorcycle with one-way clutch between the engine and the drive system nor any reports of quantitative study on its impact on the performance of the vehicle including fuel economy. The present paper reports the results of experimental research on one-way clutch employed in the drive system, obtained for motorcycles having five kinds of two-cycle engines of different displacements. The test on fuel economy showed an improvement of 4 - 9%.
Technical Paper

Improvement of Fuel Economy in a Four Stroke Spark Ignition Engine for a Small Motorcycle

1985-11-11
852238
For the purpose of reducing the fuel consumption of a motorcycle with a small-displacement, four-stroke spark-ignition engine, a compact combustion chamber was tried and the weight of the moving parts of the engine was reduced. As a result, the gas mileage under 30 km/h cruising condition was increased to 110 km/l with an improvement of 50% over a conventional motorcycle.
Technical Paper

Management System for Continuously Variable Valve Lift Gasoline Engine

2007-04-16
2007-01-1200
A continuously variable valve lift gasoline engine can improve fuel consumption by reducing pumping loss and increase maximum torque by optimizing valve lift and cam phase according to engine speed. In this research, a new control system to simultaneously ensure good driveability and low emissions was developed for this low fuel consumption, high power engine. New suction air management through a master-slave control made it possible to achieve low fuel consumption and good driveability. To regulate the idle speed, a new controller featuring a two-degree-of-freedom sliding-mode algorithm with cooperative control was designed. This controller can improve the stability of idle speed and achieve the idle operation with a lower engine speed. To reduce emissions during cold start condition, an ignition timing control was developed that combine I-P control with a sliding mode control algorithm.
Journal Article

Design Optimization of Interior Permanent Magnet Synchronous Motors for HEV & EV

2010-04-12
2010-01-1252
This paper proposes a new motor design procedure for reducing motor loss in hybrid vehicles (HEV) and electric vehicles (EV). To find an optimum design in a short time, a non-linear magnetic circuit model was developed for interior permanent magnet synchronous motors (IPMSM). Speed-torque curves and motor losses were calculated based on this model. Combined with Energy Management Simulation, this model makes it possible to find an optimum motor design with minimum loss.
Technical Paper

A Study of High Power Output Diesel Engine with Low Peak Cylinder Pressure

2010-04-12
2010-01-1107
This study examined a high-speed, high-powered diesel engine featuring a pent-roof combustion chamber and straight ports, with the objective of improving the specific power of the engine while minimizing any increase in the maximum cylinder pressure (Pmax). The market and contemporary society expect improvements in the driving performance of diesel-powered automobiles, and increased specific power so that engine displacement can be reduced, which will lessen CO2 emissions. When specific power is increased through conventional methods accompanied with a considerable increase in Pmax, the engine weight is increased and friction worsens. Therefore, the authors examined new technologies that would allow to minimize any increase in Pmax by raising the rated speed from the 4000 rpm of the baseline engine to 5000 rpm, while maintaining the BMEP of the baseline engine.
Journal Article

Development of Waterborne Conductive Primer for Motorcycles

2012-10-23
2012-32-0089
Most types of paint materials currently used for motorcycles contain large amounts of VOCs (Volatile Organic Compounds). VOCs are environmental load substances, and there is a demand to reduce emissions in recent years. Many of a motorcycle's exterior parts are made of ABS (Acrylonitrile-Butadiene-Styrene) plastics (henceforth ABS) or PA (Polyamid) plastics (henceforth PA). These two plastic materials have different film adhesion mechanisms and adhesion strength. Therefore it was necessary to use different conductive primers and that's was one of the factors which made time and material losses in the painting processes. We solved those two issues, the reduction of VOCs and the common use of the same conductive primer for different parts materials, by combining two kinds of resins originally designed as the conductive primers, i.e., urethane resins with carboxylic acid groups and acrylic resins with amide groups, which are different in properties.
Technical Paper

Development of Lithium-Ion-Battery System for Hybrid System

2011-04-12
2011-01-1372
A battery module structure and a battery management system that is optimal for the structure were developed, in order to facilitate the work of equipping hybrid cars with lithium-ion batteries (LIBs) that are expected to improve vehicle performance. This paper describes the structure of the LIB and the battery management system that is optimal for it. The battery module structure has cells with a sturdy holding structure and a highly efficient cooling system. The structure has enabled the improvement of battery pack system power output by 80% per unit weight and by 20% per unit volume compared to the previous model. The optimal management system prevents battery overcharge by detecting and controlling the state of charge (SOC) of each cell with a high degree of accuracy.
Journal Article

Development of the Methodology for FCV Post-crash Fuel Leakage Testing Incorporated into SAE J2578

2010-04-12
2010-01-0133
This paper explains the new methodology for post-crash fuel leakage testing of Fuel Cell Vehicles (FCVs) and other hydrogen vehicles utilizing compressed hydrogen storage systems. This methodology was incorporated into SAE J2578 that was revised and published in January, 2009. The new methodology is based on the concept in FMVSS 303 that specifies post-crash fuel leakage test method and criteria for CNG vehicle and adopted some modifications. Specifically, the following items are addressed: (1) Allowable leakage can be accurately evaluated in test even with large size tank that obtains only small pressure drop when a given amount of leakage occurs. A new method to deal with the influence of measurement errors was devised. (2) Even though only one option of test gas and initial filling pressure is accepted in FMVSS 303, new methodology for hydrogen system allows helium and hydrogen at reduced pressure as alternatives in addition to hydrogen at service pressure.
Technical Paper

Control Technology of Brake-by-Wire System for Super-Sport Motorcycles

2010-04-12
2010-01-0080
Super-sport motorcycles have shorter wheelbases than other category motorcycles. Due to this, strong braking occasionally causes large pitching motions to occur, including rear-wheel-lift. In order to reduce such pitching motions and achieve an effective braking force, the authors have developed a brake-by-wire system that uses a pressure sensor to detect the braking input pressure and an electric actuator to variably control the hydraulic pressure. This system makes it possible to precisely control the braking force compared with the previous ABS. Large pitching control was performed by the distribution of a front wheel and a rear-wheel braking forces, CBS (Combined Brake System), by using electronic control, and Brake-by-Wire has been suitable for sport riding. As a result, stable braking performance could be obtained without spoiling the handling characteristics of super-sport motorcycles.
Journal Article

Positioning Simulation Using a 3D Map and Verification of Positional Estimation Accuracy in Urban Areas Using Actual Measurement

2016-04-05
2016-01-0083
Positional accuracy of GPS measurement has been based on simulation and actual measurement due to the difficulty of conducting 24-hour actual running tests. However, the conventional measurement is only based on brief evaluation; hence variability of positional accuracy which varies depending on measurement time and location had been an issue. Thus, it is significant to show the validity by the estimation of positional accuracy, and actual measurement using of lengthy simulation. In this study, actual measurement data in an urban area was obtained for long hours, and a simulation using 3D maps was implemented. A high precision positional measurement system was equipped on a vehicle in order to collect actual measurements and positional data at each measurement time. The data obtained by the measurement system was used as the reference coordinate for both the simulation and the actual measurements.
Journal Article

Improving Fuel Efficiency of Motorcycle Oils

2013-10-15
2013-32-9063
As the motorcycle market grows, the fuel efficiency of motorcycle oils is becoming an important issue due to concerns over the conservation of natural resources and the protection of the environment. Fuel efficient engine oils have been developed for passenger cars by moving to lower viscosity grades and formulating the additive package to reduce friction. Motorcycle oils, however, which operate in much higher temperature regimes, must also lubricate the transmission and the clutch, and provide gear protection. This makes their requirements fundamentally very different from passenger car oils. Developing fuel efficient motorcycle oils, therefore, can be a difficult challenge. Formulating to reduce friction may cause clutch slippage and reducing the viscosity grade in motorcycles must be done carefully due to the need for gear protection.
Technical Paper

Utilization of Motor-Driven Gearshift System

1999-03-01
1999-01-0745
Recently, for passenger cars, hand operated gearshift systems have been made available by some manufacturers for the purpose of easy gearshift operation and to make driving more fun. For adapting such a system to an ATV (All Terrain Vehicle), which is used mainly for agriculture and leisure, the whole system should be compact and lightweight. It is also necessary for the clutch to be engaged properly under various running conditions. This gearshift system performs both engaging and disengaging of the clutch and moving the gearshift spindle with one motor. Since this system is controlled by calculated engine speed, vehicle speed and gear position, suitable gear shifting is realized under various running conditions. For optimal clutch control, there is a reversing point for the decreasing and increasing of engine speed for each gearshift. This accelerates the clutch engagement speed and makes quick returning of the gearshift spindle.
Technical Paper

Dynamic Simulation Software for Prediction of Hydrogen Temperature and Pressure during Fueling Process

2018-04-03
2018-01-1304
In this study, in order to relax the pre-cooling regulations at hydrogen fueling stations, we develop a software algorithm to simulate an actual hydrogen fueling process to Fuel Cell Vehicle (FCV) tanks. The simulation model in the software consists of the same filling equipment found at an actual hydrogen fueling station. Additionally, the same supply conditions (pre-cooling temperature, pressure and mass flow rate) as at a hydrogen fueling station were set to the simulation model. Based on the supply conditions, the software simulates the temperature and pressure of hydrogen in each part of filling equipment. In order to verify the accuracy of the software, we compare the temperature and pressure simulated at each stage of the filling process with experimental data. We show that by using the software it is possible to accurately calculate the hydrogen temperature and pressure at each point during the fueling process.
Technical Paper

Prediction of Piston Skirt Scuffing via 3D Piston Motion Simulation

2016-04-05
2016-01-1044
This paper describes the establishment of a new method for predicting piston skirt scuffing in the internal combustion engine of a passenger car. The authors previously constructed and reported a method that uses 3D piston motion simulation to predict piston slap noise and piston skirt friction. However, that simulation did not have a clear index for evaluation of scuffing that involves piston skirt erosion, and it impressed shortage of the predictive accuracy of a scuffing. Therefore, the authors derived a new evaluation index for piston skirt scuffing by actually operating an internal combustion engine using multiple types of pistons to reproduce the conditions under which scuffing occurs, and comparing with the results of calculating the same conditions by piston motion simulation.
Technical Paper

Influence of Shock Absorber Friction on Vehicle Ride-Comfort Studied by Numerical Simulation Using Classical Single Wheel Model

2018-04-03
2018-01-0692
Along with the suspension improvement in these two decades, it is well known that the suspension friction force became one of major parameters to affect ride comfort performance. However, it was difficult to carry out quantitative prediction on ride comfort improvement against friction force change with high correlation. It was difficult to analyze correlation between actual vehicle performance and simulation since there were difficulties in controlling damping force and friction individually. On the other hand, magneto-rheological shock absorber (MR Shock) has had several applications and widely spread to passenger vehicles. The large variation and high response of damping force especially in slow piston speed region contributes to achieve an excellent vehicle dynamics performance. However, MR Shock shows the high friction characteristics, due to the unique sliding regime of internal parts. It is said that this high friction characteristic is causing obstacles in ride-comfort.
Technical Paper

Quantitative Analysis of Leakage Suppression of DLC Coating on Piston Ring

2017-03-28
2017-01-0457
Piston ring wear in gasoline engine induces deterioration of emissions performance due to leakage of blow-by gas, instability of idling caused by reduced compression in combustion chamber, and to generate early degeneration of engine oil. We examined anti-wear performance of DLC coating on piston ring, which had been recently reported as an effective method for improving the abrasion resistance. As a result, wear rate remained low under the condition of DLC existence on sliding surface, but once DLC was worn out completely, wear of the piston ring was accelerated and its life became shorter than piston ring without DLC. In this research, we designed reciprocating test apparatus that operates at much higher velocity range, and characterized the frictional materials of the piston ring and sleeve and the DLC as a protective film, a vapor phase epitaxy (VPE) was actively used as a means to form certain level of convex and concave shape on its surface.
Technical Paper

Non-Destructive Measurement of Residual Strain in Connecting Rods Using Neutrons

2018-04-03
2018-01-1063
Increasing the strength of materials is effective in reducing weight and boosting structural part performance, but there are cases in where the residual strain generated during the process of manufacturing of high-strength materials results in a decline of durability. It is therefore important to understand how the residual strain in a manufactured component changes due to processing conditions. In the case of a connecting rod, because the strain load on the connecting rod rib sections is high, it is necessary to clearly understand the distribution of strain in the ribs. However, because residual strain is generally measured by using X-ray diffractometers or strain gauges, measurements are limited to the surface layer of the parts. Neutron beams, however, have a higher penetration depth than X-rays, allowing for strain measurement in the bulk material.
Technical Paper

Designing for Turbine Housing Weight Reduction Using Thermal Fatigue Crack Propagation Prediction Technology

2019-04-02
2019-01-0533
Turbine housings in car engine turbochargers, which use costly stainless steel castings, account for nearly 50% of the parts cost of a turbocharger. They are also the component which controls the competitiveness of the turbocharger, in terms of both function and cost. In this research, focusing on thermal fatigue resistance which is one of the main functions demanded of a turbine housing, achieving reduction in wall thickness while securing sufficient thermal fatigue resistance, it is possible to reduce the amount of material used in the turbine housing and aimed for cost reduction. Therefore, we built a method to quantitatively predict, using 3D FEM, the lifespan from the initiation of thermal fatigue cracking to the formation of a penetrating crack which leads to gas leakage.
X