Refine Your Search

Topic

Author

Affiliation

Search Results

Technical Paper

Computer simulation process for pedestrian protection structures

2000-06-12
2000-05-0222
Research into pedestrian protection has been carried out since the 1960s, in recent years there have been proposals in Europe to legislate requirements in this area and therefore the research is becoming more focused. In the draft regulation, impactor tests have been proposed as a method for evaluating the impact caused by vehicles'' body for pedestrians. This paper introduces impactor model and actual vehicle analysis as a means for simulating impactor testing. Three types of impactors for vehicle tests are presented. It is necessary that the models are first matched with the results of the calibration tests, then matched with the results of the tests on actual vehicles.
Technical Paper

Development of Programmed-Fuel Injection for Two-Stroke Cycle Racer Engine

1991-11-01
911224
An electronically controlled fuel injection system for controlling the air/fuel (A/F) ratio has been looked forward as a means for improving drivability, output characteristics, and fuel consumption of two-stroke cycle motorcycle racer engines. However, actual installation of such a system on a high output two-stroke cycle engine (which utilizes exhaust gas pressure pulsation effects) has been considered difficult for the following reasons. Fluctuation in the delivery ratio (L) during firing and misfiring becomes great due to effects from the exhaust pipe. Applying the control method used for conventional four-stroke cycle engines (by which the delivery ratio (L) is measured) would necessitate a large and heavy system. The authors have eliminated such problems by developing an electronically controlled fuel injection system, the PGM-FI (Programmed-Fuel Injection) system, which employs basic intake air flow data according to engine speed (NE) and throttle opening (θTH).
Technical Paper

Modification of Vehicle Handling Performance by Four-Wheel Steering System

1985-01-01
856039
At past ESV conferences, we have reported on a series of studies on how the driver's control performance is affected by vehicle steering response. These studies showed that a four-wheel steering system can reduce the delay in lateral acceleration response to steering action, which may result in better control performance of the driver. The present report examines the handling performance of an experimental vehicle fitted with a four-wheel steering system under a wider range of operating conditions. The studies were conducted using mathematical models and simulation of the driver-vehicle system, plus road tests. The findings indicate that the four-wheel steering system may provide better vehicle handling performance than a conventional two-wheel steering system. A vehicle incorporating this steering system may exhibit improved accident avoidance capabilities.
Technical Paper

Improvement of Fuel Economy in a Four Stroke Spark Ignition Engine for a Small Motorcycle

1985-11-11
852238
For the purpose of reducing the fuel consumption of a motorcycle with a small-displacement, four-stroke spark-ignition engine, a compact combustion chamber was tried and the weight of the moving parts of the engine was reduced. As a result, the gas mileage under 30 km/h cruising condition was increased to 110 km/l with an improvement of 50% over a conventional motorcycle.
Technical Paper

Management System for Continuously Variable Valve Lift Gasoline Engine

2007-04-16
2007-01-1200
A continuously variable valve lift gasoline engine can improve fuel consumption by reducing pumping loss and increase maximum torque by optimizing valve lift and cam phase according to engine speed. In this research, a new control system to simultaneously ensure good driveability and low emissions was developed for this low fuel consumption, high power engine. New suction air management through a master-slave control made it possible to achieve low fuel consumption and good driveability. To regulate the idle speed, a new controller featuring a two-degree-of-freedom sliding-mode algorithm with cooperative control was designed. This controller can improve the stability of idle speed and achieve the idle operation with a lower engine speed. To reduce emissions during cold start condition, an ignition timing control was developed that combine I-P control with a sliding mode control algorithm.
Technical Paper

Effects of Fuel Volatility on Combustion Characteristics of PCCI Diesel Engine

2007-07-23
2007-01-1862
In PCCI diesel engine, the fuel is injected much earlier than the injection timing of conventional diesel engines. Exhaust-emission improvements are attained by the lean-premixed combustion. It is expected that fuel properties influence mixture formation and combustion characteristics. In this research, experiments were carried out using a single-cylinder PCCI diesel engine operating on pure fuels with different volatilities. The injection timing and overall equivalence ratio of the premixed spray were varied. The results showed that the maximum heat release rate was smaller for lower-volatility fuel while ISFC was maintained smaller. So the combustion of a lower-volatility fuel would moderately make progress.
Journal Article

Design Optimization of Interior Permanent Magnet Synchronous Motors for HEV & EV

2010-04-12
2010-01-1252
This paper proposes a new motor design procedure for reducing motor loss in hybrid vehicles (HEV) and electric vehicles (EV). To find an optimum design in a short time, a non-linear magnetic circuit model was developed for interior permanent magnet synchronous motors (IPMSM). Speed-torque curves and motor losses were calculated based on this model. Combined with Energy Management Simulation, this model makes it possible to find an optimum motor design with minimum loss.
Technical Paper

A Study of High Power Output Diesel Engine with Low Peak Cylinder Pressure

2010-04-12
2010-01-1107
This study examined a high-speed, high-powered diesel engine featuring a pent-roof combustion chamber and straight ports, with the objective of improving the specific power of the engine while minimizing any increase in the maximum cylinder pressure (Pmax). The market and contemporary society expect improvements in the driving performance of diesel-powered automobiles, and increased specific power so that engine displacement can be reduced, which will lessen CO2 emissions. When specific power is increased through conventional methods accompanied with a considerable increase in Pmax, the engine weight is increased and friction worsens. Therefore, the authors examined new technologies that would allow to minimize any increase in Pmax by raising the rated speed from the 4000 rpm of the baseline engine to 5000 rpm, while maintaining the BMEP of the baseline engine.
Technical Paper

Prediction of Transient Body Deformation During Handling Maneuvers

2010-04-12
2010-01-0945
A multi-body dynamics model that considers elastic deformation of the body was formulated in order to predict transient body deformation, a factor that affects handling. A comparative analysis with body deformation during handling maneuvers identified using a modal forced response method was conducted, and a good correlation was obtained between vehicle dynamic performance, transient body deformation, and the body modal contribution factor.
Technical Paper

The Validity of EPS Control System Development using HILS

2010-04-12
2010-01-0008
In recent years, the increased use of electric power steering in vehicles has increased the importance of issues such as making systems more compact and lightweight, and dealing with increased development man-hours. To increase development efficiency, the use of a “Hardware in the loop simulator” (HILS) is being tested to shift from the previous development method that relied on a driver's subjective evaluation in an actual vehicle test to bench-test development. Using HILS enables tasks such as specification studies, performance forecasts, issue identification and countermeasure proposals to be performed at an early stage of development even when there is no prototype vehicle. This report describes a case study of using HILS to solve the issues of reducing the load by adjusting the geometric specifications around the kingpin and eliminating the tradeoff by adding a new EPS control algorithm in order to make the electric power steering (EPS) more compact and lightweight.
Journal Article

Incoming Wave Estimation Characteristics by MUSIC Method Using a Virtual Array Antenna in Urban Reception Conditions

2016-04-05
2016-01-0077
We developed “Two-Stage Method” that makes it possible to evaluate the automotive suitability of FM receivers by generating a virtual radio wave environment on a PC. The major technological challenge for the Two-Stage Method was reproducing an actual radio wave environment on PC. It was necessary to estimate the characteristics of the FM radio wave environment in tests using the Multiple Signal Classification (MUSIC) method. However, when the MUSIC method is applied to FM reception, restrictions in factors including the number of array antenna elements and the occupied bandwidth result in issues of separation performance in relation to multipath waves in urban environments. We therefore developed a MUSIC Method using a virtual array antenna, making it possible to create combinations of numbers of array and sub-array elements as desired, thus boosting multipath wave separation performance. This development was reported at the 2015 SAE World Congress.
Journal Article

Positioning Simulation Using a 3D Map and Verification of Positional Estimation Accuracy in Urban Areas Using Actual Measurement

2016-04-05
2016-01-0083
Positional accuracy of GPS measurement has been based on simulation and actual measurement due to the difficulty of conducting 24-hour actual running tests. However, the conventional measurement is only based on brief evaluation; hence variability of positional accuracy which varies depending on measurement time and location had been an issue. Thus, it is significant to show the validity by the estimation of positional accuracy, and actual measurement using of lengthy simulation. In this study, actual measurement data in an urban area was obtained for long hours, and a simulation using 3D maps was implemented. A high precision positional measurement system was equipped on a vehicle in order to collect actual measurements and positional data at each measurement time. The data obtained by the measurement system was used as the reference coordinate for both the simulation and the actual measurements.
Technical Paper

Atomization in High-Pressure Die Casting - Step 2 Simulation of Atomized Flow of Molten Aluminum by LES-VOF Method

2018-04-03
2018-01-1393
The atomization of molten aluminum when injected during high-pressure die casting is analyzed to determine its effect in enhancing the strength of the product being cast. In the previously reported first step of this study, molten aluminum was injected into open space and its atomization was observed photographically. Now in the second step of the study, a simulation is conducted to determine how the molten aluminum becomes atomized at the injection nozzle (gate) and how this atomized material flows and fills the cavity. A new simulation method is developed based on large-eddy simulation coupled with the volume-of-fluid method. The simulation system is verified by comparing its output with photographs taken in the first step of the study. Simulations are then conducted using an approximation of a real cavity to visualize how it is filled by the atomized molten aluminum.
Technical Paper

Dynamic Simulation Software for Prediction of Hydrogen Temperature and Pressure during Fueling Process

2018-04-03
2018-01-1304
In this study, in order to relax the pre-cooling regulations at hydrogen fueling stations, we develop a software algorithm to simulate an actual hydrogen fueling process to Fuel Cell Vehicle (FCV) tanks. The simulation model in the software consists of the same filling equipment found at an actual hydrogen fueling station. Additionally, the same supply conditions (pre-cooling temperature, pressure and mass flow rate) as at a hydrogen fueling station were set to the simulation model. Based on the supply conditions, the software simulates the temperature and pressure of hydrogen in each part of filling equipment. In order to verify the accuracy of the software, we compare the temperature and pressure simulated at each stage of the filling process with experimental data. We show that by using the software it is possible to accurately calculate the hydrogen temperature and pressure at each point during the fueling process.
Technical Paper

Prediction of Piston Skirt Scuffing via 3D Piston Motion Simulation

2016-04-05
2016-01-1044
This paper describes the establishment of a new method for predicting piston skirt scuffing in the internal combustion engine of a passenger car. The authors previously constructed and reported a method that uses 3D piston motion simulation to predict piston slap noise and piston skirt friction. However, that simulation did not have a clear index for evaluation of scuffing that involves piston skirt erosion, and it impressed shortage of the predictive accuracy of a scuffing. Therefore, the authors derived a new evaluation index for piston skirt scuffing by actually operating an internal combustion engine using multiple types of pistons to reproduce the conditions under which scuffing occurs, and comparing with the results of calculating the same conditions by piston motion simulation.
Technical Paper

Influence of Shock Absorber Friction on Vehicle Ride-Comfort Studied by Numerical Simulation Using Classical Single Wheel Model

2018-04-03
2018-01-0692
Along with the suspension improvement in these two decades, it is well known that the suspension friction force became one of major parameters to affect ride comfort performance. However, it was difficult to carry out quantitative prediction on ride comfort improvement against friction force change with high correlation. It was difficult to analyze correlation between actual vehicle performance and simulation since there were difficulties in controlling damping force and friction individually. On the other hand, magneto-rheological shock absorber (MR Shock) has had several applications and widely spread to passenger vehicles. The large variation and high response of damping force especially in slow piston speed region contributes to achieve an excellent vehicle dynamics performance. However, MR Shock shows the high friction characteristics, due to the unique sliding regime of internal parts. It is said that this high friction characteristic is causing obstacles in ride-comfort.
Technical Paper

Quantitative Analysis of Leakage Suppression of DLC Coating on Piston Ring

2017-03-28
2017-01-0457
Piston ring wear in gasoline engine induces deterioration of emissions performance due to leakage of blow-by gas, instability of idling caused by reduced compression in combustion chamber, and to generate early degeneration of engine oil. We examined anti-wear performance of DLC coating on piston ring, which had been recently reported as an effective method for improving the abrasion resistance. As a result, wear rate remained low under the condition of DLC existence on sliding surface, but once DLC was worn out completely, wear of the piston ring was accelerated and its life became shorter than piston ring without DLC. In this research, we designed reciprocating test apparatus that operates at much higher velocity range, and characterized the frictional materials of the piston ring and sleeve and the DLC as a protective film, a vapor phase epitaxy (VPE) was actively used as a means to form certain level of convex and concave shape on its surface.
Technical Paper

Prediction of Power Transmission Efficiency for Two-Mode Half-Toroidal IVT

2018-04-03
2018-01-1060
Infinitely variable transmission (IVT) is one of the methods used to extend the ratio coverage. In this paper, a dynamic behavior analysis technology was developed for an IVT utilizing a half-toroidal variator as the shifting device. The traction coefficient of traction fluid used for the half-toroidal IVT varies greatly according to contact surface slip rate, contact pressure and fluid temperature. This paper used measurement values from a four-roller machine to identify the coefficient, and then applied it to the dynamic behavior analysis. Use of the identified traction coefficient enabled power transmission characteristic predictions of a half-toroidal variator. To reproduce the elastic deformation in actual operation, the research used the Finite Element Method (FEM) for modeling. This model was also used to visualize the frictional state of traction surfaces during operation.
Technical Paper

Non-Destructive Measurement of Residual Strain in Connecting Rods Using Neutrons

2018-04-03
2018-01-1063
Increasing the strength of materials is effective in reducing weight and boosting structural part performance, but there are cases in where the residual strain generated during the process of manufacturing of high-strength materials results in a decline of durability. It is therefore important to understand how the residual strain in a manufactured component changes due to processing conditions. In the case of a connecting rod, because the strain load on the connecting rod rib sections is high, it is necessary to clearly understand the distribution of strain in the ribs. However, because residual strain is generally measured by using X-ray diffractometers or strain gauges, measurements are limited to the surface layer of the parts. Neutron beams, however, have a higher penetration depth than X-rays, allowing for strain measurement in the bulk material.
Technical Paper

Designing for Turbine Housing Weight Reduction Using Thermal Fatigue Crack Propagation Prediction Technology

2019-04-02
2019-01-0533
Turbine housings in car engine turbochargers, which use costly stainless steel castings, account for nearly 50% of the parts cost of a turbocharger. They are also the component which controls the competitiveness of the turbocharger, in terms of both function and cost. In this research, focusing on thermal fatigue resistance which is one of the main functions demanded of a turbine housing, achieving reduction in wall thickness while securing sufficient thermal fatigue resistance, it is possible to reduce the amount of material used in the turbine housing and aimed for cost reduction. Therefore, we built a method to quantitatively predict, using 3D FEM, the lifespan from the initiation of thermal fatigue cracking to the formation of a penetrating crack which leads to gas leakage.
X