Search Results

Further improvement in fuel consumption is needed for diesel engines to address regulatory requirement particularly for heavy duty diesel in Japan enforced in 2015, in addition to the compliance to the regulatory requirements for exhaust emission, which seems to be more stringent in future. The authors have participated in the project of “Comprehensive Technological Development of Innovative, Next-Generation, Low-Pollution Vehicles” organized by New Energy and Industrial Technology Development Organization (NEDO), and innovative devices such as multi stage boosting system, ultra high-pressure fuel injection system and variable valve actuation (camless) system had been developed in this project from a standpoint of simultaneous improvement of fuel consumption and exhaust emission. In camless system, intake and exhaust valves are driven by hydraulic pressure. So, fully flexible setting of opening and closure timings and lift of the intake and exhaust valves is possible.

Study of DME diesel engines was conducted to improve fuel consumption and emissions of its. Additionally, DME trucks were built for the promotion and the road tests of these trucks were executed on EFV21 project. In this paper, results of diesel engine tests and DME truck driving tests are presented. As for DME diesel engines, the performance of a DME turbocharged diesel engine with LPL-EGR was evaluated and the influence of the compression ratio was also explored. As for DME trucks, a 100,000km road test was conducted on a DME light duty truck. After the road test, the engine was disassembled for investigation. Furthermore, two DME medium duty trucks have been developed and are now the undergoing practical road testing in each area of two transportation companies in Japan.

Various premixed diesel combustion concepts are suggested as the way of simultaneous reduction of NOx and PM emission from diesel engines. However, every combustion concept has common problems, such as difficulty of ignition timing control, a great deal of HC and CO emissions and limiting the operation region to low load operation. The purpose of this study is to expand the operation region of Premixed Compression Ignition (PCI) combustion, which is a premixed diesel combustion concept that realizes the fuel injection around the top dead center. As a result of examining it with EGR, supercharging operation and low compression ratio piston, PCI combustion region was expanded to cover higher load operation. And the high load region was limited by not only stoichiometric air fuel ratio but also permissible maximum in-cylinder pressure.

1 A novel analysis approach called “Regression Density method” was developed for better understanding of fuel property effects on exhaust emission. The approach was applied to diesel emission data obtained in JCAP programs and emission models were conducted to analyze the effects of fuel properties and engine conditions on emissions. By introducing this analysis method, the relationship between density factor and aromatics factor (chemical composition factor) was identified, however, they have been reported previously as dominant factors in fuel properties. The effects of engine conditions and fuel properties on emissions were investigated quantitatively based on the statistically conducted emission models to clarify universal ways to emission reduction. The mechanism of emission formation of vehicles and engines with characteristic behavior was also examined.

Single cylinder engine testing was carried out to clearly understand the test results of multi-cylinder engines reported by the Diesel WG in JCAP (Japan Clean Air Program) (1), (2), (3) and (4). In this tests, engine specifications such as fuel injection pressure, nozzle hole diameter, turbo-charging pressure, EGR rate, and fuel properties such as 1-, 2-, 3-ring aromatics content, n-,i-paraffins content, and T90 were parametrically changed and their influence on the emissions were studied. PM emission generally increased in each engine condition with increased aromatic contents and T90. In particular, multi ring aromatics brought about large increases in PM regardless of the engine conditions. The influence of fuel properties on NOx emission is smaller than the influence on PM emission. Some other fuels that have various side chain structures of 1-ring aromatics, normal paraffins only and various naphthene contents were also investigated.

Premixed diesel combustion was performed and various characteristics examined with fuel injection timing near top dead center (TDC). A lean and uniform fuel-air mixture was found to during 25° C.A. with a narrow injection angle (27.5° with respect to horizontal), shallow dish combustion chamber, and low cetane number fuel (CN=19). These conditions enabled low NOx combustion in no exhaust gas re-circulation (EGR), despite fuel injection timing around 25° BTDC. Furthermore, HC emissions were lower than with premixed diesel combustion of the early injection type. Because fuel injection timing was near TDC, the volume of the mixture dispersed to a squish area was decreased. This combustion mode was also achieved with a high-cetane fuel (conventional diesel fuel) and high EGR rate conditions. However, in this case, it was difficult to adjust the ignition timing near top dead center. This combustion system also showed good performance in conventional diesel combustion mode.

It is well known that a high-pressure fuel injection is effective for the reduction in particulates and smoke emissions. Exhaust gas recirculation (EGR) is effective for the reduction in NOX emission. In this study an experiment aiming to understand more comprehensive combustion under the condition of EGR and high-pressure fuel injection was carried out by using gas sampling method for the purpose of understanding what occurred inside the spray before and after combustion. The number of combustion cycles in this engine can be controlled in order to change EGR conditions by adjusting the residual gas concentration in the cylinder. Main results were: (1) Close to the nozzle tip, the sampling gas data showed little reaction which implies that combustion never occurs in this area during the injection period. (2) In the case of high-pressure fuel injection O2 concentration decreased faster and air dilution was more active and earlier.

In-cylinder total sampling technique utilizing a single-cylinder diesel engine equipped with hydraulic valve actuation system has been developed. In this study, particulate matter (PM) included in the in-cylinder sample gas was collected on a quartz filter, and the polycyclic-aromatic hydrocarbons (PAHs) component and soot were subsequently quantified by thermal desorption-gas chromatograph mass spectrometry (TD-GCMS) and a carbon analyzer, respectively. Cylinder-averaged histories of PAHs and soot were obtained by changing the sampling timing. It was found that decreasing intake oxygen concentration suppresses in-cylinder soot oxidation, and the fuel with higher aromatic and naphthenic contents accelerates soot production.

A reduced chemical kinetic model of diesel fuel, which can be applied to computational fluid dynamics (CFD) simulation coupled with detailed chemistry using the CONVERGE software, is developed to simulate the particulate matter (PM) formation process. We analyzed the influence of varying intake oxygen concentrations and fuel composition on the polycyclic aromatic hydrocarbons (PAHs) and soot formation processes. When the intake oxygen concentration was decreased, no significant difference was observed in PAH formation associated with soot formation, and the soot mass generated after the peak was high. When the fuel contained high levels of aromatics and naphthene, the PAH and soot formation mass increased. These tendencies were in good agreement with experimental results [1].