Search Results

Partly competing objectives, as low fuel consumption, low friction, long oil maintenance rate, and at the same time lowest exhaust emissions have to be fulfilled. Diminishing resources, continuously reduced development periods, and shortened product cycles yield detailed knowledge about oil consumption mechanisms in combustion engines to be essential. There are different ways for the lubricating oil to enter the combustion chamber: for example as blow-by gas, leakage past valve stem seals, piston rings (reverse blow-by) and evaporation from the cylinder liner wall and the combustion chamber. For a further reduction of oil consumption the investigation of these mechanisms has become more and more important. In this paper the influence of the mixture formation and the resulting fuel content in the cylinder liner wall film on the lubricant oil emission was examined.

Large Eddy Simulation (LES) appears today as a prospective tool for engine study. Even if recent works have demonstrated the feasibility of multi-cycle LES, they have also pointed out a lack of detailed experimental data for validation as well as for boundary condition definition. The acquisition of such experimental data would require dedicated experimental set-ups. Nevertheless, in future industrial applications, unconditional dedicated experimental set-ups will not be the main stream. To overcome this difficulty, a methodology is proposed using system simulation to define fluid boundary conditions (crank-resolved intake/exhaust pressures and temperatures) and wall temperatures. The methodology combines system simulation for the whole experimental set-up and LES for the flow in the combustion chamber as well as a part of the intake and exhaust ducts. System simulation provides the crank-resolved temperature and pressure traces at the LES mesh inlet and outlet.

Burned gas recirculation is emerging as a promising technology to reduce fuel consumption without compromising performance in turbocharged spark ignited engines. This recirculation can be done internally through Internal Gas Residual (IGR) using Variable Valve Timing (VVT) or externally through classical Exhaust Gas Recirculation circuit (EGR). Both have a large impact on combustion. The purpose of the paper is to give clues to get the best compromise at moderate load between these two technologies in terms of fuel consumption. This experimental work was performed on a Gasoline Direct Injection (GDI) engine, 2.0L displacement, dual independent VVT, equipped with a Low Pressure, cooled and catalyzed EGR loop (LP EGR). The load region covers 6 to 10 bar Indicated Mean Effective Pressure (IMEP). EGR rates obtained vary between 0 and 15%. IGR variation is obtained by using the VVT in order to vary the valve overlap. IGR rates vary from 4 to 8%.

Fuels derived from biomass will most likely contain oxygen due to the high amount of hydrogen needed to remove oxygen in the production process. Today, alcohol fuels (e. g. ethanol) are well understood for spark ignition engines. The Institute for Combustion Engines at RWTH Aachen University carried out a fuel investigation program to explore the potential of alcohol fuels as candidates for future compression ignition engines to reduce engine-out emissions while maintaining engine efficiency and an acceptable noise level. The soot formation and oxidation process when using alcohol fuels in diesel engines is not yet sufficiently understood. Depending on the chain length, alcohol fuels vary in cetane number and boiling temperature. Decanol possesses a diesel-like cetane number and a boiling point in the range of the diesel boiling curve. Thus, decanol was selected as an alcohol representative to investigate the influence of the oxygen content of an alcohol on the combustion performance.

Advanced technologies such as direct injection DI, turbocharging and variable valve timing, have lead to a significant evolution of the gasoline engine with positive effects on driving pleasure, fuel consumption and emissions. Today's developments are primarily focused on the implementation of improved full load characteristics for driving performance and fuel consumption reduction with stoichiometric operation, following the downsizing approach in combination with turbocharging and high specific power. The requirements of a relatively small cylinder displacement with high specific power and a wide flexibility of DI injection specifications lead to competing development targets and additionally to a high number of degrees of freedom during optimization. In order to successfully approach an optimum solution, FEV has evolved an advanced development methodology, which is based on the combination of simulation, optical diagnostics and engine thermodynamics testing.

The modern engine development process is characterized by shorter development cycles and a reduced number of prototypes. However, simultaneously exhaust after-treatment and emission testing is becoming increasingly more sophisticated. It is expected that predictive simulation tools that encompass the entire powertrain can potentially improve the efficiency of the calibration process. The testing of an ECU using a HiL system requires a real-time model. Additionally, if the initial parameters of the ECU are to be defined and tested, the model has to be more accurate than is typical for ECU functional testing. It is possible to enhance the generalization capability of the simulation, with neuronal network sub-models embedded into the architecture of a physical model, while still maintaining real-time execution. This paper emphasizes the experimental investigation and physical modeling of the port fuel injected SI engine.

SI engines with gasoline direct injection are currently the focus of development for almost all car manufacturers. After the introduction of DISI engines, first to the Japanese market and after a short time delay also in Europe, a broad variety of technical solutions for efficient stratified concepts can be stated. The targets of the development activities in this field are defined by legislation and customer's demands. The potential reduction of fuel consumption with stratified operation has to be combined with a further improvement of the full load potential of the DISI engine. A substantial part of the development activities are the fulfillment of current and future emission standards. Therefore, in order to realize a highly efficient lean operation, new technologies and strategies in the field of exhaust gas aftertreatment and vehicle application are required.

Today, SULEV legislation represents the most stringent emission standard for vehicles with combustion engines, and it will be introduced starting by Model Year 2003. In order to meet such standards, even higher effort is required for the development of the exhaust gas emission concept of SI engines. Beyond a facelift of the combustion system, exhaust gas aftertreatment, and the engine management system, new approaches are striven for. The principle keys are well known: low HC feed gas, high thermal load for quick light-off, exhaust system with low heat capacity and highly effective exhaust gas aftertreatment.

The main goal in the development of new automobile SI engines is to significantly reduce fuel consumption. To this end both, variable valve actuation and direct gasoline injection, are being pursued as new engine concepts. Both approaches appear to offer approximately the same potential to reduce fuel consumption. The development so far is creating the impression of two competing technical concepts with no obvious way to combine them [1]. The two engine concepts, however, can be combined, although it is often objected that their combination would only yield marginal additional potential. That is true to the extent that the advantages of dethrottling offered by both of the concepts can only be counted once in terms of overall potential. But there is a number of additional effects to be taken into account. This Paper represents an analysis of the individual potential of the two approaches as well as an estimation of their combined potential.

In order to meet the CO₂ challenge, today a wide variety of solutions are developed in the automotive industry such as advanced technologies (downsizing, VVA, VCR), new combustion modes (HCCI, stratified and lean combustion), hybridization, electrification or alternative fuels. Furthermore, couplings between these solutions can be envisaged, increasing considerably the number of degrees of freedom which have to be accounted for in the development of future powertrains. Consequently, for time and cost reasons, it is not obvious to evaluate and optimize the full potential of new concepts only by the mean of experimental investigation. In this context, system simulation appears as a powerful and relevant complement to engine tests for its flexibility and its high CPU efficiency. This paper focuses on the development of a methodology combining both simulation and experimental tools to quantify the interest of innovative solutions in the very first steps of their development.

The fuel film thickness resulting from fuel spray impingement on a flat transparent window was characterized in a high pressure high temperature cell for various thermodynamic conditions, injection pressures, injection durations, fuel types and injector technologies by Refractive Index Matching technique. The ambient conditions at injection timing were similar to that of a direct injection spark ignition engine at Top Dead Center, with the distance between the injector tip and the impinging surface set to 10 mm. The spray axis was set normal to the rough transparent window surface at ambient temperatures of 453 K, 573 K and 673 K, and ambient densities of 5.0 kg/m₃, 6.0 kg/m₃ and 6.5 kg/m₃. Injection pressures of 100 and 200 bar were investigated. Three injector technologies were studied: piezo-electric, multi-holes and swirl types. Two fuels, iso-octane and model gasoline, were tested.

In spark-ignition engines, cyclic variability limits the optimisation of operating conditions (choice of spark advance and/or injection timing) since it induces load variations and the occurrence of misfire and/or knock. This, in turn, restricts the operation range of new concepts such as downsizing or stratified combustion. To understand the basic physical phenomena behind cyclic variations, careful experimental studies are necessary to simultaneously characterise the combustion and the unsteady flow in the complete engine set-up. With a well-characterised experimental engine set-up, Large Eddy Simulation (LES) modelling can be easily combined with experiment in order to tackle intricate physical phenomena couplings. This paper describes an experimental database acquired on an optical research engine. The single-cylinder spark-ignition engine is equipped with four valves, a pentroof combustion chamber and a flat piston. The database is dedicated to the validation of LES models.

The requirement of reducing worldwide CO₂ emissions and engine pollutants are demanding an increased use of bio-fuels. Ethanol with its established production technology can contribute to this goal. However, due to its resistive auto-ignition behavior the use of ethanol-based fuels is limited to the spark-ignited gasoline combustion process. For application to the compression-ignited diesel combustion process advanced ignition systems are required. In general, ethanol offers a significant potential to improve the soot emission behavior of the diesel engine due to its oxygen content and its enhanced evaporation behavior. In this contribution the ignition behavior of ethanol and mixtures with high ethanol content is investigated in combination with advanced ignition systems with ceramic glow-plugs under diesel engine relevant thermodynamic conditions in a high pressure and temperature vessel.

Acoustics influence on internal combustion engine volumetric efficiency is obvious and the use of modeling to represent its effect is largely spread. In this regard, LMS has developed a new 1D model library, namely CFD1D, to model engine intake and exhaust lines under LMS Imagine. Lab AMESim platform. Simulations have been performed at IFP Energies nouvelles (IFPEN) to compare duct system modeling with two different approaches: on the one side, with the brand new 1D library and on the other side, with state-of-the-art 0D lumped parameter models (IFP-Engine library under the same platform). This paper aims at comparing 0D and 1D modeling strategies for two naturally-aspirated spark-ignition engines: a single-cylinder propane-fueled engine and a Honda K20A engine with a dedicated intake system used for a cylinder deactivation concept development. For each application, a 0D and a 1D intake system model is realized, based on real engine test-bed geometry.

Compared to Spark Ignition (SI) engines, Compression Ignition (CI) engines are more efficient because of the higher compression ratios and leaner operation. However, thanks to stoichiometric air fuel ratio, SI engines allow efficient pollutants after treatment, particularly for NOx emissions. In this context, IFP Energies nouvelles (IFPEN) has developed the concept of diesel-gasoline combustion in order to combine the advantages of both fuels and both combustion processes. Focusing on a passenger car application, experiments have been performed using a modified DI turbocharged small diesel engine (the combustion chamber has been redesigned and port fuel injectors have been added). In-Cylinder Fuel Blending (ICFB) using port-fuel-injection of gasoline and optimized direct injection of diesel was used to control combustion phasing and duration. This modified engine can still run on diesel alone.

In spark-ignition engines, Cycle-to-Cycle Variations (CCV) limit the optimization of engine operation since they induce torque variations and the occurrence of misfire and/or knock. A mean for limiting the related negative impact of CCV on fuel consumption and emissions would be control strategies able to address them. At present, engine simulation codes used for control purposes can only describe CCV linked to variations of gas exchanges in the air loop. CCV of the in-cylinder flow motion cannot be naturally captured by classical quasi-dimensional combustion chamber models. A convenient way to mimic CCV is to impose stochastic distributions of the combustion model parameters. Nevertheless, it is not always clear if these perturbations have physical bases as well as realistic ranges of variation.

Dedicated experiments were performed in an optically-accessible, constant volume combustion vessel whose geometry and aerodynamic flow was representative of a pentroof SI engine combustion chamber. A detailed characterization of the flowfield was conducted in several near-wall regions where flame-wall interaction occurs using high-speed Particle Image Velocimetry (PIV). Simultaneous heat flux measurements were also performed at these same spatial locations. From a numerical point of view, current Reynolds Averaged Navier Stokes (RANS) or Large Eddy Simulation (LES) models take into account the effects of the wall on the flame however the effects of the turbulent flame-wall interaction on wall heat flux are not accounted for. Direct Numerical Simulations (DNS) of a 2D, premixed, steady-state V-flame were performed in order to aid the development and validation of a new model based on the flame surface density concept in order to take into account flame-wall interaction effects [1].

A main focus of development in modern SI engine technology is variable valve timing, which implies a high potential of improvement regarding fuel consumption and emissions. Variable opening, period and lift of inlet and outlet valves enable numerous possibilities to alter gas exchange and combustion. However, this additional variability generates special demands on the calibration process of specific engine control devices, particularly under cold start and warm-up conditions. This paper presents procedures, based on Hardware-in-the-Loop (HiL) simulation, to support the classical calibration task efficiently. An existing approach is extended, such that a virtual combustion engine is available including additional valve timing variability. Engine models based purely on physical first principles are often not capable of real time execution. However, the definition of initial parameters for the ECU requires a model with both real time capability and sufficient accuracy.

In the recent years, it has become obvious that one of the main fields of interest in alternate fuels is the public transportation sector. Natural Gas seems to be advantageous. It is available and environmentally friendly, even if the greenhouse effect of methane is considered. The operation range of vehicles running on CNG (Compressed Natural Gas) is poor due to the large pressure vessels, but in case of urban buses with low daily mileage this is acceptable. On the other hand, the use of an environmentally friendly fuel is favorable especially in urban areas. Although there are some advantages of Natural Gas, diesel buses dominate the market. The reason is the better part-load fuel efficiency of the Diesel principle which is superior to the Otto-cycle due to the absence of engine throttling. The efficiency levels of Spark-Ignition (SI) -type, Lean Burn Natural Gas engines are quite comparable to diesel engines during full load conditions.

The development of new passenger car powertrains with gasoline direct- injection engines is facing new requirements which result from the need of different operational modes with stratified and homogeneous air-fuel mixture. Moreover, the exhaust aftertreatment system causes a discontinuous operation with lean-burn absorption periods followed by short rich spikes for catalyst regeneration. Recent work on combustion system development has shown, that gasoline direct injection can create significant fuel economy benefits. Charge motion controlled combustion systems have proven to be of advantage in terms of low raw emissions compared to wall-guided concepts. Based on an initial single-cylinder development phase, a multi-cylinder engine was realized with excellent fuel economy, low raw emissions and operational robustness. Finally, the new engine''s potential has been demonstrated in a mid-class vehicle.