Refine Your Search

Topic

Search Results

Technical Paper

The Mvma Investigation Into the Complexities of Heavy Truck Splash and Spray Problem

1985-01-01
856097
Splash and spray conditions created by tractor-trailer combinations operating on the Federal highway system have been studied and tested for many years with mixed results. Past events are reviewed briefly in this paper. In additional testing during 1983, using new state-of- the-art splash/spray suppressant devices, some encouragement was provided that these devices could work. The 1984 Motor Vehicle Manufacturers Association (MVMA) test program was designed to develop practicable and reliable test procedures to measure effectiveness of splash and spray reduction methods applied to tractor-trailer combination vehicles. Over 40 different combinations of splash/spray suppression devices on five different tractors and three van trailer types were tested. The spray-cloud densities for some 400 test runs were measured by laser transmissometers and also recorded by still photography, motion pictures, and videotape. On-site observers made subjective ratings of spray density.
Technical Paper

Applications of Monte Carlo Simulation to Vehicle Maintenance and Component Remanufacturing Decisions

1983-02-01
830550
As component and systems sophistication in both cars and trucks increase, improved diagnostic capabilities are required to assure proper and expedient serviceability. Replacement of electrical modules, starter motors, carburetors, fuel injectors and even whole engines or transmissions is encouraged by high labor costs and continued vehicle mobility mandates. The remanufacturing business has grown and components previously discarded now provide valuable core elements to feed the industry. To achieve efficient utilization of capital, equipment and labor, remanufacturers must estimate when this supply of core elements will be available and plan their production schedules accordingly. In order to properly service private individuals and commercial fleets, minimize vehicle downtime and reduce life cycle costs, adaptation of available analytical tools must be made.
Technical Paper

How VMRS Helps the Manufacturers

1978-02-01
780269
The Vehicle Maintenance Reporting Standards of the American Trucking Associations can be used by manufacturers to improve heavy-duty vehicles. After verifying the accuracy and significance of the data the manufacturing, engineering, technical service and marketing departments can all use the information to improve vehicles and provide better service to the user.
Technical Paper

Describing the Truck Driver Eye and Head Accommodation Tools

1987-08-01
871531
Truck driver eye and head position tools have been developed to describe where certain percentages of truck drivers position there eyes and heads in various workspace arrangements. Separate equations describe the accommodation level for driver populations with male to female ratios of 50/50, 75/25, and a range from 90/10 to 95/5. These equations can be used as a design tool to locate the curves in vehicle space to describe the region behind which the given populations eyes and heads would be located. Equations and curves are provided for both the drivers eye and head in the side view. It has become increasingly apparent that there is a need for improved methods of accommodating truck drivers in heavy truck cab design. Currently, practices used in the automobile industry for passenger car design are utilized for the design of heavy trucks. These practices.
Technical Paper

Describing the Truck Driver Stomach and Shin-Knee Accommodation Tools

1987-08-01
871532
Truck driver shin-knee and stomach postion tools have been developed to describe where certain percentages of truck drivers position there knees and stomachs in various workspace arrangements. Separate equations describe the accommodation level for driver populations with male to female ratios of 50/50, 75/25, and a range from 90/10 to 95/5. These equations can be used as a design tool to locate the curves in vehicle space to describe the region behind which the given populations shin-knees, and stomachs would be located. Equations and curves are provided for both the left leg, which operates the clutch, and the right leg, which operates the accelerator.
Technical Paper

Heavy Truck Safety - The Need To Know

1981-08-01
810839
This paper provides an overview of the current state of knowledge on medium and heavy truck safety and reviews the results of truck safety research sponsored by the Motor Vehicle Manufacturers Association. A number of issues have been raised about the accident experience of trucks, and the injuries and fatalities sustained by occupants. The diverse viewpoints and perceptions which exist on the reasons for these accidents and what countermeasures should be taken are reviewed. The evolutionary nature of truck accident research is presented, pointing out that sufficient detailed accident and injury data are lacking. Corresponding information on truck configuration, size, weight and exposure data remain inadequate. The role of the vehicle, driver, and highway environment in accident causation must be known and methods to achieve this goal are examined. Despite these limitations, there is progress in understanding the causes of truck accidents.
Technical Paper

A New Concept for Heavy Duty Highway Tractors

1975-02-01
751018
Prior to World War II, most heavy duty highway trucks and tractors were built as Conventionals, i. e., with the cab mounted behind the engine. In the late 1940's cab-over-engine types gained acceptance and in the 1950's the tilt cab COE was developed in its present form including sleeper cabs. The new concept is to combine the best features of conventionals and tilt cab COEs to develop a superior non-sleeper tractor that makes no compromises for sleeper cab types.
Technical Paper

Simulation of Densification in Powder Metal Forging

1989-02-01
890413
Finite Element Method (FEM) simulation of the powder metal forging process can be a useful tool in new product or process development because the simulation provides tooling load estimates, press size requirements, preform design feasibility and allows accurate and inexpensive parametric studies of forging process variables. Several examples of simulations using ALPID-P code are presented. Axisymmetric and plane strain simulations at several cross sections of an automotive P/M connecting rod forging indicate that die wall friction has a large effect on the densification process. Also, simulations indicate a significant die wall velocity effect on densification.
Technical Paper

Sideband and Sound Field Spatial Considerations in the Measurement of Gear Noise

2005-05-16
2005-01-2517
Measurement of gear noise requires accurate measurement of gear mesh harmonic sound levels. The sound signal may include sidebands, such that the frequency bandwidth and computation method of respective “order tracking” analysis will have a profound effect on measured sound levels. A further consideration is the spatial distribution of the sound field inside typical passenger cars and light duty trucks, in which sound levels can change dramatically within small distances. This paper provides a discussion of the data processing and measurement location effects at hand. It explains their influence and provides guidelines for their selection.
Technical Paper

Rollover Sensor Signature Test Development

2007-04-16
2007-01-0375
Although rollover crashes represent a small fraction (approximately 3%) of all motor vehicle crashes, they account for roughly one quarter of crash fatalities to occupants of cars, light trucks, and vans (NHTSA Traffic Safety Facts, 2004). Therefore, the National Highway Traffic Safety Administration (NHTSA) has identified rollover injuries as one of its safety priorities. Motor vehicle manufacturers are developing technologies to reduce the risk of injury associated with rollover collisions. This paper describes the development by General Motors Corporation (GM) of a suite of laboratory tests that can be used to develop sensors that can deploy occupant protection devices like roof rail side air bags and pretensioners in a rollover as well as a discussion of the challenges of conducting this suite of tests.
Technical Paper

POWERMATIC A New Automatic for Chevrolet Transmission Heavy-Duty Trucks

1957-01-01
570012
THIS paper describes the development of a truck automatic transmission, from a statement of broad objectives through the growing pains, to road testing of the final product. Emphasis is placed upon original thinking that led to the decision to undertake such a project, compromises that suggested themselves throughout the various stages, and features tried and found wanting as well as those retained. The finished product is described full though not in detail, stress being placed upon interesting and novel design features.
Technical Paper

IH High-Speed Lightweight Diesels

1960-01-01
600053
THE NEW DIESEL ENGINES developed recently by International Harvester are adaptations of existing carbureted truck engines. The manufacturing economies possible by employing existing machine tools were the governing consideration in their design. This paper discusses solutions found to the many problems presented by this approach to engine design: crankshaft, crankcase, connecting rods, pistons, lubricating system, and the like. Extensive interchangeability of parts was a result of the design concept. The engines have been successfully adapted to farm tractors, crawler tractors, stationary motors, and various automotive applications.*
Technical Paper

Front Suspension Multi-Axis Testing

1987-11-01
872255
A front suspension laboratory test procedure was developed to reproduce time-correlated fatigue damaging events from a light truck road durability test. Subsequently, the performance of front suspension systems for the GMT 400 light truck program were evaluated in terms of customer reliability. Both prototype and pilot testing, as well as computer modeling, were used in the evaluation.
Technical Paper

2003 Chevrolet Kodiak and GMC TopKick Airbag Sensing System Development

2002-11-18
2002-01-3101
Airbag systems have been part of passenger car and truck programs since the mid-1980's. However, systems designed for medium and heavy duty truck applications are relatively new. The release of airbag systems for medium duty truck has provided some unique challenges, especially for the airbag sensing systems. Because of the many commercial applications within the medium duty market, the diversity of the sensing environments must be considered when designing and calibrating the airbag sensing system. The 2003 Chevrolet Kodiak and GMC TopKick airbag sensing development included significant work, not only on the development of airbag deployment events but also non-deployment events – events which do not require the airbag to deploy. This paper describes the process used to develop the airbag sensing system deployment events and non-deployment event used in the airbag sensing system calibration.
Technical Paper

The Design and Development of the 2003 Chevrolet Kodiak and GMC TopKick Medium Duty Trucks

2002-11-18
2002-01-3100
For model year 2003, the General Motors Corporation is introducing new medium duty trucks - the Chevrolet Kodiak and GMC TopKick. These new trucks replace the previous versions of the Kodiak and TopKick medium duty trucks that were introduced in 1989 and the Chevrolet and GMC 3500HD that debuted in the 1991 model year. This new series of trucks marks a clear change in General Motors' strategy in the medium duty marketplace. It emphasizes General Motors' strong commitment to the medium duty market, as well as a strong focus on customer needs, vehicle quality and reliability. This paper describes the General Motors strategy in the medium duty market, along with the history of the design and development of these new products. Finally, this paper will discuss performance to program objectives.
Technical Paper

Washcoat Technology and Precious Metal Loading Study Targeting the California LEV MDV2 Standard

1996-10-01
961904
Meeting the California Medium-Duty truck emissions standards presents a significant challenge to automotive engineers due to the combination of sustained high temperature exhaust conditions, high flow rates and relatively high engine out emissions. A successful catalyst for an exhaust treatment system must be resistant to high temperature deactivation, maintain cold start performance and display high three-way conversion efficiencies under most operating conditions. This paper describes a catalyst technology and precious metal loading study targeting a California Medium-Duty truck LEV (MDV2) application. At the same time a direction is presented for optimizing toward the Federal Tier 1 standard through reduction of precious metal use. The paper identifies catalytic formulations for a twin substrate, 1.23 L medium-coupled converter. Two are used per vehicle, mounted 45 cm downstream of each manifold on a 5.7 L V8 engine.
Technical Paper

Truck Aerodynamics

1962-01-01
620531
A requirement for larger trucks and higher operating speed is indicated. The present report presents wind tunnel data on drag of a Chevrolet truck-trailer combination. Possible means of drag reduction are examined. Although side force and yawing moment data are presented, their effect on directional stability are not, at present analyzed.
Technical Paper

A Unique Concept in Off-Highway Trucks

1965-02-01
650283
A study to define accurately and discover new parameters of productivity for the contractor has resulted in a new design concept in off-highway trucks. This new concept has been first applied in the International Model 180 Payhauler, a rear dump vehicle of 45 ton rated capacity. The function and form criteria are discussed by components and systems in terms of the complete vehicle and on the job applications.
Technical Paper

The Truck Noise Problem, and What Might Be Done About It

1972-02-01
720624
From various sources of information it is clear that truck noise is a definite public nuisance. Early noise control efforts were very productive in that many heavy duty trucks did not have mufflers, and the addition of this device made clear improvements. Further improvement requires treatment of many sources significant to the overall level. It is felt that today's “tight but attainable” 88 dBA for heavy trucks can reduce to 86 dBA by 1975 and 8k dBA by 1978 with a lot of hard work. There is promise for meaningful noise regulation in the “real world” as indicated by “calibratability” of non-standard sites.
X