Search Results

Nowadays, developing of effective camless engine systems, allowing Variable Valve Actuation (VVA), is one of the fundamental automotive challenge to increase engine power, reduce fuel consumption and pollutant emissions, as well as improve the engine efficiency significantly. Electromechanical devices based on double electromagnets have shown to be a promising solution to actuate engine valves during normal engine cycle due to their efficient working principle. Conversely, this solution requires special care at the key-on engine for the first valve lift, when the valve must be shifted from the middle equilibrium position to the closing one with limited coil currents and power requirements as well. Despite the central role of the first catching problem, few attempts have been done into the existing literature to tackle it systematically.

High pressure diesel sprays were visualized under vaporizing and combusting conditions in a constant-volume combustion vessel. Near-simultaneous visualization of vapor and liquid phase fuel distribution were acquired using a hybrid shadowgraph/Mie-scattering imaging setup. This imaging technique used two pulsed LED's operating in an alternative manner to provide proper light sources for both shadowgraph and Mie scattering. In addition, combustion cases under the same ambient conditions were visualized through high-speed combustion luminosity measurement. Two single-hole diesel injectors with same nozzle diameters (100μm) but different k-factors (k0 and k1.5) were tested in this study. Detailed analysis based on spray penetration rate curves, rate of injection measurements, combustion indicators and 1D model comparison have been performed.

Swirling flows are very dominant in applied technical problems, especially in IC engines, and their prediction requires rather sophisticated modeling. An adaptive low-pass filtering procedure for the modeled turbulent length and time scales is derived and applied to Menter' original k - ω SST turbulence model. The modeled length and time scales are compared to what can potentially be resolved by the computational grid and time step. If the modeled scales are larger than the resolvable scales, the resolvable scales will replace the modeled scales in the formulation of the eddy viscosity; therefore, the filtering technique helps the turbulence model to adapt in accordance with the mesh resolution and the scales to capture.

In the next years, the upcoming emission legislations are expected to introduce further restrictions on the admittable level of pollutants from vehicles measured on homologation cycles and real drive tests. In this context, the strict control of pollutant emissions at the cold start will become a crucial point to comply with the new regulation standards. This will necessarily require the implementation of novel strategies to speed-up the light-off of the reactions occurring in the after-treatment system, since the cold start conditions are the most critical one for cumulative emissions. Among the different possible technological solutions, this paper focuses on the evaluation of the potential of a burner system, which is activated before the engine start. The hypothetical burner exploits the lean combustion of an air-gasoline mixture to generate a high temperature gas stream which is directed to the catalyst section promoting a fast heating of the substrate.

In recent years, the increase of gasoline fuel injection pressure is a way to improve thermal efficiency and lower engine-out emissions in GDI homogenous combustion concept. The challenge of controlling particulate formation as well in mass and number concentrations imposed by emissions regulations can be pursued improving the mixture preparation process and avoiding mixture inhomogeneity with ultra-high injection pressure values up to 100 MPa. The increase of the fuel injection pressure in GDI homogeneous systems meets the demand for increased injector static flow, while simultaneously improves the spray atomization and mixing characteristics with consequent better combustion performance. Few studies quantify the effects of high injection pressure on transient gasoline spray evolution. The aim of this work was to simulate with OpenFOAM the spray morphology of a commercial gasoline injected in a constant volume vessel by a prototypal GDI injector.

The European Union road transport CO2 emissions regulation foresees mandatory targets for passenger vehicles. However, several studies have shown that there is a divergence between official and real-world values that could range up to 40% compared to the NEDC reference value. The introduction of the Worldwide Harmonized Test Protocol (WLTP) limited this divergence, but it is uncertain whether it can adequately address the problem, particularly considering future evolutions of vehicle technology. In order to address this issue, the recent EU CO2-standards regulation introduces the monitoring of on-road fuel consumption and subsequently CO2 emissions by utilizing On-Board Fuel Consumption Meters (OBFCM). In the near future, all vehicles should provide instantaneous and lifetime-cumulative fuel consumption signals at the diagnostics port. Currently, the fuel consumption signal is not always available.

The electrochemical performance of a lithium-ion battery is strongly affected by the temperature. During charge and discharge cycles, batteries are subjected to an increment of temperature that can accelerate aging and loss of efficiency if critical values are reached. Knowing the thermal parameters that affect the heat exchange between the battery surface and the surrounding environment (air, cooling fins, plates, etc…) is fundamental to their thermal management. In this work, thermal imaging is applied to a laminated lithium-polymers battery as a non-invasive temperature-indication method. Measurements are taken during the discharge phase and the following cooling down until the battery reaches the ambient temperature. The 2d images are used to analyze the homogeneity of the temperature distribution on the battery surface. Then, experimental results are coupled with mathematical correlations.

Cycle-To-Cycle Variability (CCV) must be properly considered when modeling the ignition process in SI engines operating with ultra-lean mixtures. In this work, a strategy to model the impact of the ignition type on the CCV was developed using the RANS approach for turbulence modelling, performing multi-cycle simulations for the power-cycle only. The spark-discharge was modelled through a set of Lagrangian particles, introduced along the sparkgap and interacting with the surrounding Eulerian gas flow. Then, at each discharge event, the velocity of each particle was modified with a zero-divergence perturbation of the velocity field with respect to average conditions. Finally, the particles velocity was evolved according to the Simplified Langevin Model (SLM), which keeps memory of the initial perturbation and applies a Wiener process to simulate the stochastic interaction of each channel particle with the surrounding gas flow.

The common realization of the necessity to reduce the use of mineral sources is promoting the use of alternative fuels. Big efforts are being made to replace petroleum derivatives in the internal combustion engines (ICEs). For this purpose it is mandatory to evaluate the behavior of non-conventional fuels in the ICEs. The optical diagnostics have proven to be a powerful tool to analyze the processes that take place inside the engine. In particular, 2d imaging in the infrared range can reveal new details about the effect of the fuel properties since this technique is still not very common. In this work, a comparison between commercial diesel fuel and two non-conventional fuels has been made in an optically accessible diesel engine. The non-conventional fuels are: the first generation biofuel Rapeseed Methyl Ester (RME) and an experimental blend of diesel and a fuel with high glycerol content (HG).

The paper reports an experimental study on the effect of compression ratio variation on the performance and pollutant emissions of a single-cylinder light-duty research diesel engine operating in DF mode. The architecture of the combustion system as well as the injection system represents the state-of-the-art of the automotive diesel technology. Two pistons with different bowl volume were selected for the experimental campaign, corresponding to two CR values: 16.5 and 14.5. The designs of the piston bowls were carefully performed with the 3D simulation in order to maintain the same air flow structure at the piston top dead center, thus keeping the same in-cylinder flow characteristics versus CR. The engine tests choice was performed to be representative of actual working conditions of an automotive light-duty diesel engine.

The modeling of fuel sprays under well-characterized conditions relevant for heavy-duty Diesel engine applications, allows for detailed analyses of individual phenomena aimed at improving emission formation and fuel consumption. However, the complexity of a reacting fuel spray under heavy-duty conditions currently prohibits direct simulation. Using a systematic approach, we extrapolate available spray models to the desired conditions without inclusion of chemical reactions. For validation, experimental techniques are utilized to characterize inert sprays of n-dodecane in a high-pressure, high-temperature (900 K) constant volume vessel with full optical access. The liquid fuel spray is studied using high-speed diffused back-illumination for conditions with different densities (22.8 and 40 kg/m3) and injection pressures (150, 80 and 160 MPa), using a 0.205-mm orifice diameter nozzle.

Knock occurrence and fuel enrichment, which is required at high engine speed and load to limit the turbine inlet temperature, are the major obstacles to further increase performance and efficiency of down-sized turbocharged spark ignited engines. A technique that has the potential to overcome these restrictions is based on the injection of a precise amount of water within the mixture charge that can allow to achieve important benefits on knock mitigation, engine efficiency, gaseous and noise emissions. One of the main objectives of this investigation is to demonstrate that water injection (WI) could be a reliable solution to advance the spark timing and make the engine run at leaner mixture ratios with strong benefits on knock tendency and important improvement on fuel efficiency.

Pursuing a sustainable energy scenario for transportation requires the blending of renewable oxygenated fuels such as alcohols into commercial hydrocarbon fuels. From a chemical kinetic perspective, this requires the accurate description of both hydrocarbon reference fuels (n-heptane, iso-octane, toluene, etc.) and oxygenated fuels chemistry. A recent systematic investigation of linear C2-C5 alcohols ignition in a rapid compression machine at p = 10-30 bar and T = 650- 900 K has extended the scarcity of fundamental data at such conditions, allowing for a revision of the low temperature chemistry for alcohol fuels in the POLIMI mechanism. Heavier alcohols such as n-butanol and n-pentanol present ignition characteristic of interest for application in HCCI engines, due to the presence of the hydroxyl moiety reducing their low temperature reactivity compared to the parent linear alkanes (i.e. higher octane number).

A vital element of any vehicle-certification test is the use of representative values for the vehicle resistance forces. In most certification procedures, including the WLTP recently adopted by the EU, the latter is achieved mainly through coast down tests. Subsequently, the resistance values measured are used for setting up the chassis-dyno resistances applied during the laboratory measurements. These reference values are obtained under controlled conditions, while a series of corrections are applied to make the test procedure more repeatable and reproducible. In real driving, the actual vehicle road loads are influenced by a series of factors leading to a divergence between the certified fuel consumption values, and the real-world ones. An approach of calculating representative road loads during on-road tests can help to obtain a more unobstructed view of vehicle efficiency and, when needed, confirm the officially declared road loads.

Isooctane sprays from a multi-hole GDI injector were investigated in a constant volume chamber by means of high speed imaging techniques. The tests were performed under inert conditions (nitrogen), at temperatures and densities ranging between representative operating conditions of late injection, flash boiling and early injection in a GDI engine. The global parameters of the sprays were obtained by processing Schlieren, Shadowgraph, DBI and Mie-scattering images through an in-house image processing method. Thus, the boundaries of the spray vapor phase can be easily detected with great accuracy, regardless of whether Schlieren or the less sensitive shadowgraph imaging is used. Furthermore, the boundaries of the liquid phase were also obtained from shadowgraph images and compared with those obtained through DBI and scattering. The results show that the signature of the liquid phase in a shadowgraph image can be distinguished from that of the vaporized fuel.

A test rig (named RuotaVia) is presented for the in-door testing of road vehicle suspension systems. It is basically a drum (ϕ 2.6 m) providing a running surface for testing the dynamic performance of a single tire or suspension system (corner). The suspension system is instrumented for the measurement of the forces and the moments acting at each joint connecting the suspension to the car body. A new 6 axis load cell was designed and manufactured for this purpose. The accelerations in various locations of the system (wheel carrier, suspension arms, …) and the wheel centre displacements in the longitudinal and vertical directions are monitored. The effect of the dynamic interaction between the test rig and the suspension system is discussed in the paper. The direct measurement of the forces and moments at the suspension-chassis joints is still an effective way for understanding the vibration and harshness (VH) suspension performances.

To meet the future stringent emission standards, innovative diesel engine technology, exhaust gas after-treatment, and clean alternative fuels are required. Oxygenated fuels have showed a tendency to decrease internal combustion engine emissions. In the same time, advanced fuel injection modes can promote a further reduction of the pollutants at the exhaust without penalty for the combustion efficiency. One of the more interesting solutions is provided by the premixed low temperature combustion (LTC) mechanism jointly to lower-cetane, higher-volatility fuels. In this paper, to understand the role played by these factors on soot formation, cycle resolved visualization, UV-visible optical imaging and visible chemiluminescence were applied in an optically accessed high swirl multi-jets compression ignition engine. Combustion tests were carried out using three fuels: commercial diesel, a blend of 80% diesel with 20% gasoline (G20) and a blend of 80% diesel with 20% n-butanol (BU20).

In the last ten years, the number of natural gas vehicles worldwide has grown rapidly with the biggest contribution coming from the Asia-Pacific and Latin America regions. As natural gas is the cleanest fossil fuel, the exhaust emissions from natural gas spark ignition vehicles are lower than those of gasoline powered vehicles. Moreover, natural gas is less affected by price fluctuations and its resources are more evenly widespread over the globe than to oil. However, as natural gas vehicles are usually bi-fuel gasoline and natural gas, the excellent knock resistant characteristics of natural gas cannot be completely exploited. This paper shows the results of an experimental activity performed on a passenger car fuelled alternatively by gasoline and compressed natural gas (CNG). The vehicle has been tested on a chassis dynamometer over standard (NEDC) and real driving cycles (Artemis CADC), allowing to investigate a wide range of operating conditions.

Hydroplaning represents a threat for riding safety since a wedge of water generated at the tire-road interface can lift tires from the ground thus preventing the development of tangential contact forces. Under this condition directionality and stability of the vehicle can be seriously compromised. The paper aims at characterizing the tire lateral response while approaching the hydroplaning speed: several experimental tests were carried out on a special test track covered with a 8-mm high water layer using a vehicle equipped with a dynamometric hub on the front left wheel. A series of swept sine steer maneuvers were performed increasing the vehicle speed in order to reach a full hydroplaning condition. Variations of tire cornering stiffness and relaxation length were investigated while the vehicle approaches the hydroplaning speed. Experimental tests stated that a residual capability of generating lateral forces is still present also close to the full hydroplaning condition.

Many studies have been carried out to optimize the aerodynamic performances of a single car or a single vehicle. In present days the traffic increases and sophisticated technologies are developing to guarantee the drivers safety, to minimize the fuel consumption and be more environmentally friendly. Within this research area a new technique that is being studied is Platooning: this means that different vehicles travel in a configuration that minimizes the aerodynamic drag and therefore the fuel consumption and the longitudinal space. In the present study platoons with different vehicles and configurations are taken into account, to analyze the influence of car shape and relative distance between the vehicles. The research has been carried out using CFD techniques to investigate the different flow fields around different platoons, while wind tunnel tests have been used to validate the results of the CFD simulations.