Search Results

A novel predictable tire model has been proposed for combined braking and cornering forces, which is based on only a few pure baking and pure cornering tests. It avoids elaborate testing of all kinds of combinations of braking and side forces, which are always expensive and time consuming. It is especially important for truck or other large size tires due to the capability constraints of tire testing facilities for combined shear forces tests. In this paper, the predictive model is based on the concept of slip circle and state stiffness method. The slip circle concept has been used in the COMBINATOR model to obtain the magnitude of the resultant force under combined slip conditions; however the direction assumption used in the COMBINATOR is not suitable for anisotropic tire slip stiffness.

For diesel/natural gas dual fuel engines, the combustion of pilot diesel injection plays an important role to subsequent mixture combustion process. To better understand the effects of multiple injections, a detailed study was conducted on a 6-cylinder turbocharged intercooler diesel/natural gas dual fuel heavy-duty engine at low loads. Multiple variables were tested, including the single injection timings, the multiple injections timings and the mass ratios. The investigated results showed that the multiple pilot diesel injections have an obvious effect on not only pilot diesel combustion process but also natural gas mixture combustion process. Early injection leads to a pilot-diesel-ignition-mode and it is a two-stage auto ignition mode. This mode differs from the compression ignition mode of traditional diesel engine in regard to its random occurrence location within the spray.

The quality of the brake system is a significant safety factor in commercial vehicles on the roads. With the development of automobile technology, the single function ABS system didn't meet active safety requirements of the user. The Electronically Controlled Brake System (EBS) system will replace the ABS system to become the standard safety equipment of commercial vehicles in the near future. EBS can be said an enhanced ABS system, it contains load sensor, brake valve sensor and pressure sensor of chamber, etc, and it is more advantages than ABS. This paper describes a flexible integrated test bench for ABS/EBS Electronic Control Unit (ECU) based on Hardware-In-the-Loop (HIL) simulation technique. It consists of most commercial vehicle pneumatic braking system components (from brake pedal valve, brake caliper to brake chambers), and uses the dSPACE real-time simulation system to communicate to the hardware I/O interface.

In order to improve the braking energy recovery, a parallel hybrid electric bus simulation model with electric braking system (EBS) was established by co-simulation platform for the TruckSim and Matlab/Simulink in this paper. EBS makes the front and rear shaft braking force arbitrarily distributed, which is more effective to improve the rate of energy recovery and the braking stability. A braking force distribution algorithm for hybrid electric bus based on EBS was designed in this paper. Under the premise to meet the driver's needs and the ECE regulations, this braking force distribution method focuses on making the braking force distribute to the drive shaft to a maximum extent, so as to obtain the maximum energy recovery rate by the utilization of the motor regenerative braking. At last, the simulation in different operating conditions was used to analyze the braking energy utilization and the braking performance based on the simulation model.

In order to reasonably match the variable stiffness suspension and optimize the ride comfort and stability of a light bus, a virtual prototype model of the light bus was established in Adams-Car. Before the optimization, the tyre mechanical characteristics were tested by using a plate-type tyre tester, then the magic formula model of the tyre (Pac2002) was obtained by means of the global parameter identification method. The vertical vibration of the virtual model was simulated with the simulated B-class road profile, and its handling stability performance was also studied by simulation of the pylon course slalom test and steady static circular test. After that, an optimal method of the variable stiffness suspension was put forward. In the proposed method, the two-level stiffness (k1, k2) and the damping of the rear suspension and the torsional stiffness of the pre and post stabilizer bars were taken as the optimal variables.

This paper presents a torque distribution algorithm to improve the energy efficiency of four-wheel-drive (4WD) electric vehicles with PMSM hub motors. In order to optimize the torque distribution method, at first the motor model considering the affect of iron loss and the loss model of multi-motors drive system of 4WD electric vehicle with PMSM hub motors, which operate at straight-line condition, are established. Besides, realize the online identification of motor parameters based on the MARS, which is important for updating the loss model parameters of the motor drive system. By doing this, the ideal torque distribution ratio can be obtained from the loss model in real-time. The simulation result using different distribution algorithms shows that the optimized torque distribution algorithm based on the loss model can be useful for improving the energy efficiency.