Search Results

Due to the nearly silent operation of an electric motor, it is difficult for pedestrians to detect an approaching electric vehicle. To address this safety concern, the National Highway Traffic Safety Administration issued the Federal Motor Vehicle Safety Standard (FMVSS) No. 141, “Minimum Sound Requirements for Hybrid and Electric Vehicles”. This FMVSS 141 standard requires the measurement of electric vehicle noise according to certain test protocols; however, performing these tests can be difficult since inconsistent results can occur in the presence of transient background noise. Methods to isolate background noise during static sound measurements have already been established, though these methods are not directly applicable to a pass-by noise test where neither the background noise nor the vehicle itself as it travels past the microphone produce stationary sound signals.

Multiple plate disc clutches are used extensively for shifting gears in automatic transmissions. In the active clutches that engage or disengage during a shift the automatic transmission fluid (ATF) and friction material experience large changes in pressure, P, sliding speed, v, and temperature, T. The coefficient of friction, μ, of the ATF and friction material is a function of these variables so μ = μ(P,v,T) also changes during clutch engagement. These changes in friction coefficient can lead to noise or vibration if the ATF properties and clutch friction material are improperly matched. A theoretical understanding of what causes noise, vibration and harshness (NVH) in shifting clutches is valuable for the development of an ATF suitable for a particular friction material. Here we present a theoretical model that identifies the slope, ∂μ/∂T, of the coefficient of friction with respect to temperature as a major contributor to the damping in a clutch during engagement.

The torsional natural frequencies of axles equipped with limited slip differential clutches depend on whether or not the tires and clutches are slipping since the effective inertia at each end of the axle is different for slipping and non-slipping conditions. Limited slip axle vibrations are typically analyzed for one tire slipping and the other not since that is the case for which the limited slip clutches are used. Vibrations often arise, however, during normal turning when both drive tires have good traction.

FMVSS 223 and 224 set standards for “Rear Impact Protection” for trailers and semi-trailers with a gross weight rating greater than 10000 pounds. A limited amount of experimental data is available for evaluating the different performance attributes of rear impact guards. The crash tests are usually limited to fixed parameters such as impact speed, guard height, strength and energy absorption, etc. There also seems to be some misunderstanding of the interdependence of guard strength and energy absorption, and their combined effect on the guard's ability to limit underride while keeping occupant acceleration forces in a safe range. In this paper, we validated the Finite Element (FE) model of an existing rear impact guard against actual FMVSS 223 tests. We also modified a previously evaluated FE model of a 1990 Ford Taurus by updating its hood geometry and material properties.

Modeling and simulation of dynamic systems is not always a simple task. In this paper, the mathematical model of a 4 Degree Of Freedom (DOF) ride model is presented using a bond-graph technique with state energy variables. We believe that for the physical model as described in this research, the use of a bond-graph approach is the only feasible solution. Any attempt to use classical methods such as Lagrange equations or Newton's second law, will create tremendous difficulties in the transformation of a set of second order linear differential equations to a set of first order differential equations without violating the existence and the uniqueness of the solution of the differential equations, the only approach is the elimination of the damping of the tires, which makes the model unrealistic. The bond-graph model is transformed to a mathematical model. Matlab is used for writing a computer script that solves the engineering problem.

The transmission mount in a powertrain mounting system is often a primary path for noise. This is especially the case when the transmission is mounted directly to the body without the benefit of a structural frame or isolation between the bracket and body. Since most transmissions generate frequencies above 150Hz, the transmission mount system becomes a likely noise path for this and higher frequencies. A combination of very stiff transmission bracket and very soft rubber mount between the transmission bracket and the transmission would help this problem. In this paper the development an optimally designed transmission mount for a longitudinally mounted powertrain is presented. The development procedure of such a design considers the transmission mount as part of the total system.

The kinematics and kinetics of a seven degree of freedom vehicle ride model with independent front and rear suspension are developed. Lagrange's equation is used to obtain the mathematical model of the vehicle. The equations of motion are transformed to state space equations in Linear Time Invariant (LTI) form. The effect of Chassis Design Factors (CDF) such as stabilizer bars, stiffness', Dynamic Index in Pitch (DIP) and mass ratio on the vehicle ride quality are investigated. The ride quality of the 3 dimensional vehicle that includes bounce, pitch, roll and unsprung masses motion is demonstrated in time domain response. The vehicle is considered as a Multi-Input-Multi-Output System (MIMO) subjected to deterministic ground inputs. Outputs of interest for the ride quality investigation are vertical and angular displacement and vertical accelerations. Numerical computer simulation analysis is performed using MATLAB® software.

Tires are one of the major sources of noise and vibration in vehicles. The vibration characteristic of a tire depends on its resonant frequencies and mode shapes. Hence, it is desirable to study how different parameters affect the characteristics of tires. In the current paper, experimental modal tests are performed on a tire in free-free and fixed conditions. To obtain the mode shapes and the natural frequencies, the tire is excited using a mechanical shaker and the response of the tire to the excitation is measured using three roving tri-axial accelerometers. The mode shapes and resonant frequencies of the tire are extracted using LMS PolyMax modal analysis. The obtained mode shapes in the two configurations are compared using Modal Assurance Criterion (MAC) to show how mode shapes of tires change when the tire is moved from a free-free configuration to a fixed configuration. It is shown that some modes of the tire are more sensitive to boundary conditions.

Doors inside an automotive HVAC module are essential components to ensure occupant comfort by controlling the cabin temperature and directing the air flow. For temperature control, the function of a door is not only to close/block the airflow path via the door seal that presses against HVAC wall, but also control the amount of hot and cold airflow to maintain cabin temperature. To meet the stringent OEM sealing requirement while maintaining a cost-effective product, a “V-Shape” soft rubber seal is commonly used. However, in certain conditions when the door is in the position other than closed which creates a small gap, this “V-Shape” seal is susceptible to the generation of objectionable whistle noise for the vehicle passengers. This nuisance can easily reduce end-customer satisfaction to the overall HVAC performance.

Sliding contact between friction surfaces occurs in numerous torque transfer elements: torque converter clutches, shifting clutches, launch or starting clutches, limited slip differential clutches, and in the meshing of gear teeth under load. The total temperature in a friction interface is the sum of the equilibrium temperature with no sliding and a transient temperature rise, the flash temperature, caused by the work done while sliding. In a wet shifting clutch the equilibrium temperature is typically the bulk oil temperature and the flash temperature is the temperature rise during clutch engagement. The flash temperature is an important factor in the performance and durability of a clutch since it affects such things as the reactivity of the sliding surfaces and lubricant constituents (e.g., oxidation) and thermal stress in the components. Knowing how high the flash temperature becomes is valuable for the formulation of ATF, gear oil, engine oil and other lubricants.

Multiple plate disk clutches are used extensively for shifting gears in automatic transmissions. In a shift from one gear to another one or more clutches is engaging or disengaging. In these active clutches the automatic transmission fluid (ATF) and friction material experience large changes in pressure P, temperature T, and sliding speed v. The coefficient of friction, μ, of the ATF and friction material depends on v, P and T, and also changes during clutch engagement. Changes in μ can lead to vibration and poor shift quality if the ATF and clutch friction material are improperly selected. An in-depth theoretical understanding of the cause of vibration in shifting clutches is crucial in the development of a suitable ATF to work with a particular friction material.

A comprehensive finite element methodology is developed to predict the compressible flow performance of a non-symmetric 7-blade axial flow fan, and to quantify the source strength and sound pressure levels at any location in the system. The acoustic and flow performances of the fan are predicted simultaneously using a computational aero-acoustic technique combining transient flow analysis and noise propagation. The calculated sound power levels compare favorably with the measured sound power data per AMCA 300-96 code.

For virtual simulation of the vehicle attributes such as handling, durability, and ride, an accurate representation of pneumatic tire behavior is very crucial. With the advancement in autonomous vehicles as well as the development of Driver Assisted Systems (DAS), the need for an Intelligent Tire Model is even more on the increase. Integrating sensors into the inner liner of a tire has proved to be the most promising way in extracting the real-time tire patch-road interface data which serves as a crucial zone in developing control algorithms for an automobile. The model under development in Kettering University (KU-iTire), can predict the subsequent braking-traction requirement to avoid slip condition at the interface by implementing new algorithms to process the acceleration signals perceived from an accelerometer installed in the inner liner on the tire.

The automotive and aerospace industries are increasingly using the light-weight material to improve the vehicle performance. However, using light-weight material can increase the airborne and structure-borne noise. A special attention needs to be paid in designing the structures and measuring their dynamics. Conventionally, the structure is excited using an impulse hammer or a mechanical shaker and the response is measured using uniaxial or multi-axial accelerometers to obtain the dynamics of the structure. However, using contact-based transducers can mass load the structure and provide data at a few discrete points. Hence, obtaining the true dynamics of the structure conventionally can be challenging. In the past few years, stereo-photogrammetry and three-dimensional digital image correlation have received special attention in collecting operating data for structural analysis. These non-contact optical techniques provide a wealth of distributed data over the entire structure.

This paper aims to study the NVH and acoustic performance of a 3-phase AC induction motor in order to develop an approach to reduce the magnetic component of noise from an electric motor in an electric vehicle (EV). The final goal of this project is to reduce the magnetic component of sound from the motor by making modifications to the end bracket of the motor housing. EVs are being considered the future of mobility mainly due to the fact that they are environment-friendly. As many companies are already investing in this technology, electric drives are set to become extremely popular in the years to come. The heart of an EV is its motor. Modern electric vehicles are quiet, furthermore with the lack of an IC engine to mask most sounds from other components, the sound from the electric motor and other auxiliary parts become more prominent.

A model and simulation results are presented for the torsional dynamics of a rear wheel driveline while the vehicle is coasting in a turn. The model includes the effects of road load and powertrain drag, limited slip differential clutch friction, the inertias of the vehicle, wheels, axles, differential carrier, and driveshaft, the final drive ratio, torsional stiffnesses of the axles and driveshaft, vehicle track width, and radius of the turn. The dynamics of coasting in a turn differ from powered driving due to changes in the inertia loading the driveshaft, the damping effect of the disengaged transmission, and nonlinearities in the clutch friction. Specific focus is given to vibration in the axles and driveshaft due to variations in the torque-speed slope of the clutches, which is determined by the slope of the friction coefficient ‘μ’ versus sliding speed ‘v’ in the limited slip clutches.

Data-driven modeling can help improve understanding of the governing equations for systems that are challenging to model. In the current work, the Sparse Identification of Nonlinear Dynamical systems (SINDy) is used to predict the dynamic behavior of dynamic problems for NVH applications. To show the merit of the approach, the paper demonstrates how the equations of motions for linear and nonlinear multi-degree of freedom systems can be obtained. First, the SINDy method is utilized to capture the dynamic behavior of linear systems. Second, the accuracy of the SINDy algorithm is investigated with nonlinear dynamic systems. SINDy can output differential equations that correspond to the data. This method can be used to find equations for dynamical systems that have not yet been discovered or to study current systems to compare with our current understanding of the dynamical system.

This work aims to present the application of mode coupling to a Formula Student racing vehicle and propose a solution. The major modes of a vehicle are heave, pitch, roll, and warp. All these modes are highly coupled – which means changing suspension rates or geometry will affect all of them – while alleviating some and making others worse characteristics. Decoupling these modes, or at least some of them, would provide more control over suspension setup and more refined race car dynamics for a given layout of the racetrack. This could improve mechanical grip and yield significant performance improvements in closed-circuit racing. If exploited well, this approach could also assist in the operation of the vehicle at an optimal kinematic state of the suspension systems, to gain the best wheel orientations and maximize grip from the tires under the high lateral accelerations and varied excitations seen on a typical road course.