Search Results

Mode transition between low temperature combustion (LTC) and conventional combustion was performed by changing the exhaust gas recirculation (EGR) rate from 60% to 0% or vice versa in a light duty diesel engine. The indicated mean effective pressure (IMEP) before mode transition was set at 0.45 MPa, representing the maximum load of LTC in this research engine. Various engine operating parameters (rate of EGR change, EGR path length, and residual gas) were considered in order to investigate their influence on the combustion mode transition. The characteristics of combustion mode transition were analyzed based on the in-cylinder pressure and hydrocarbon (HC) emission of each cycle. The general results showed that drastic changes of power output, combustion noise, and HC emission occurred during the combustion mode transition due to the improper injection conditions for each combustion mode.

It is known that SEA is a rapid and simple methodology for analyzing complex vibroacoustic systems. However, the SEA principle is not always valid and one has to be careful about the physical conditions at which the SEA principle is acceptable. In this study, the appropriate damping loss factor of the vehicle interior cavity is studied in the viewpoint of the modal overlap factor of the cavity and the decay per mean free path (DMFP) of the cavity. Virtual SEA tests are performed with an FE model combination, which is suggested by a previous study of Stelzer et al. for the simulation of the sound transmission loss (STL) of vehicle panel structure. The FE model combination is consisting of the body in white (BIW), an acoustical-excited hemisphere-shaped exterior cavity, and the interior cavity. It is found that the DMFP of the interior cavity is appropriate between 0.5 ~ 1 dB for applying SEA principle.

Pressure variation during engine combustion generates torque fluctuation that is delivered through the driveline. Torque fluctuation delivered to the tire shakes the vehicle body and causes the body components to vibrate, resulting in booming noise. HKMC (Hyundai Kia Motor Company)’s TMED (Transmission Mounted Electric Device) type generates booming noises due to increased weight from the addition of customized hybrid parts and the absence of a torque converter. Some of the improvements needed to overcome this weakness include reducing the torsion-damper stiffness, adding dynamic dampers, and moving the operation point of the engine from the optimized point. These modifications have some potential negative impacts such as increased cost and sacrificed fuel economy. Here, we introduce a method of reducing lock-up booming noise in an HEV at low engine speed.

High-voltage battery system plays a critical role in eco-friendly vehicles due to its effect on the cost and the electric driving range of eco-friendly vehicles. In order to secure the customer pool and the competitiveness of eco-vehicle technology, vehicle electrification requires lowering the battery cost and satisfying the customer needs when driving the vehicles in the real roads, for example, maximizing powers for fun drive, increasing battery capacities for achieving appropriate trip distances, etc. Because these vehicle specifications have a critical effect on the high-voltage battery specification, the key technology of the vehicle electrification is the appropriate decision on the specification of the high-voltage battery system, such as battery capacity and power. These factors affect the size of battery system and vehicle under floor design and also the profitability of the eco-friendly vehicles.

Passenger fatigue during long distance driving is greatly influenced by the comfort performance of the seat. Seat comfort performance is determined by the appropriate contour of the seat and the appropriate pad with sufficient thickness. The height of vehicle has been lowered to enhance car styling, and battery for electric vehicle applied to the underbody of the vehicle, reducing the package space of the seat in the vehicle. These external factors eventually lead to a reduced pad thickness of the seat cushion and compromise one of the important components in the seat cushion compartment, creating an uncomfortable cushioning problem when driving long distances. To improve the cushion composition of the seat within a limited package, air bladders are applied to the underside of the cushion pad. In addition, the function to support the buttocks using the air bladders of the lower cushion, similar to lumbar support for the back, was implemented to improve cushion comfort performance.

In order to understand the automotive PEM fuel cell system, mathematical system modeling is conducted and the model is implemented and simulated by using the Matlab®/Simulink®. The components such as fuel cell stack, air supplier, and radiator are modeled individually and integrated into a system level. The PEM fuel cell system operation control includes thermal management, air supply control, hydrogen supply control, fuel cell stack protection control, and load following control. In the thermal management, the inlet and outlet temperature of coolant are controlled to operate the fuel cell stack in desired temperature range and to prevent flooding inside the fuel cell stack. In air supply control and hydrogen supply control, the flow rates of air and hydrogen are controlled not to starve the fuel cell stack according to the output current. A control structure for the system is developed and confirmed by using the developed simulation model.

Adopting the Spray-guided Gasoline Direct Injection (SGDI) concept, a new multi-cylinder engine has designed. The engine has piezo injectors at the central position of its combustion chamber, while sparkplugs are also at the center. The sparkplug location is designed so that the spark location is at the outer boundary of the fuel spray where the appropriate air-fuel mixture is formed. A few important operating parameters are chosen to investigate their effects on the combustion stability and fuel consumption. The final experimental results show a good potential of the SGDI engine; the fuel consumption rate was much less than that of the base Multi Port Injection (MPI) engine at various engine operating conditions.

We used a one-dimensional monolithic catalyst model to predict the transient thermal and conversion characteristics of a dual monolithic catalytic converter with a Palladium only (Pd-only) catalyst and a Palladium/Rhodium (Pd/Rh) catalyst. Prior to the numerical investigation of the dual-catalyst converter, we modified the pre-exponential factor and activation energy of each reaction for both catalysts to achieve acceptable agreement with experimental data under typical operating conditions of automobile applications. We validated the conversion behavior of the lumped parameter model for each catalyst against different engine operating conditions. Two higher cell density substrates, Pd-only catalyst (600cpsi/3.9mil) and Pd/Rh catalyst (600cpsi/4mil), for faster light-off and improved warm-up performance are used in this study and the two monoliths has been connected without the space between monoliths.

The purpose of this paper is to investigate the air/fuel mixture formation and combustion characteristics in a spray-guided GDI engine using a commercial code, STAR-CD. This engine adopted the outwardly opening injector located in the center of cylinder head, which forms a hollow cone spray. The spray injection was modeled arranging multiple points using random function along the ring-shaped nozzle exit. To predict the breakup of spray, Reitz-Diwakar's breakup model was used, and the model constants were calibrated against published experimental data in a constant volume chamber. The validated spray models were applied to the analysis of spray behavior and mixture formation process inside the engine combustion chamber under operating condition of ultra-lean mixture (λ ≈ 4). To predict the combustion process, the modified eddy breakup combustion model was applied.

CAI (Controlled Auto Ignition) combustion is already well known to be advantageous over conventional cycles in that it facilitates higher engine efficiency and has low emission characteristics. The CAI combustion process is mainly governed by in-cylinder RGF (Residual Gas Fraction), therefore achieving good control of in-cylinder RGF is essential in the development of CAI combustion engine. Usually, in-cylinder RGF controlled via low lift cam, short valve duration and negative valve overlap. More importantly on the other hand, accurate and instantaneous prediction of RGF must be done as a prerequisite to control. However, on-line prediction of RGF is not always practical due to the requirement of expensive fast response exhaust gas analyzers in the empirical case or otherwise due to theoretical models which are just too slow for application by means of simulation solving. In this paper, a newly enhanced theoretical model for predicting on-line in-cylinder RGF is introduced.

In this study a new model is proposed for turbulent premixed combustion in a spark-ignition engine. An independent transport equation is solved for the mean reaction progress variable in a propagation form in KIVA-3V. An expression for turbulent burning velocity was previously given as a product of turbulent diffusivity in unburned gas, laminar flame speed and maximum flame surface density. The model has similarity with the G equation approach, but originates from zone conditionally averaged formulation for unburned gas. A spark kernel grows initially as a laminar flame and becomes a fully developed turbulent flame brush according to a transition criterion in terms of the kernel size and the integral length scale. Simulation of a homogeneous charge pancake chamber engine showed good agreement with measured flame propagation and pressure trace. The model was also applied against experimental data of Hyundai θ-2.0L SI engine.

The development of a new method to evaluate the NVH quality of diesel combustion noise bases upon following questions by regarding typical driving modes: Driving behavior with diesel vehicles Which driving situation causes an annoying diesel combustion noise Judgment of diesel combustion noise as good or bad A suitable test course was determined to regard typical driving situations as well as the European driving behavior. Vehicles of different segments were tested on that course. The recorded driving style and the simultaneously given comments on the diesel combustion noise results to a typical driving mode linked to acoustics sensation of diesel combustion noise. The next step was to simulate this driving mode on the chassis dynamometer for acoustical measurements. The recordings of several vehicles were evaluated in listening test to identify a metric. The base of metric was objective analyses evaluating diesel combustion noise in relevant driving situations.

For a complete automotive HVAC system, it is desirable to keep good air quality control for the interior vehicle cabin. This experimental study for evaluating the CO2 concentration levels in a vehicle cabin was done on the roads in South Korea. Increasing levels of CO2 can cause a passenger to become tired, sleepy and cause headaches or discomfort. The study results shows that CO2 and fine dust concentration is a result of the number of passengers,_driving condition and HVAC user settings. The result from this investigation can be used to establish a development guide for air quality in a vehicle cabin.

To reduce diesel engine emissions, a split injection strategy with PHCCI combustion in a diesel engine was investigated with simulation. A multidimensional CFD application, Star-CD coupled with a modified 2-D flamelet was used to simulate multiple injection combustion. Several mass ratios of the first injection and second injection conditions compared to the conventional pilot and main injection strategy were evaluated. The injection angle and the injection timing of the first injection were fixed to 150° and 55° BTDC, respectively. Because of the early injection, the in-cylinder pressure and temperature were much lower than those of normal injection conditions, and the fuel could not fully evaporate. As a result, wall impingement can be occurred, and THC and CO would be increased. To eliminate the wall impingement, the injection timing of the first injection was then retarded to 35-30° BTDC, and the piston bowl geometry was modified to capture droplets in the piston bowl.

The combustion characteristics of a HSDI diesel engine were analyzed numerically using a reduced chemical kinetics. The reaction mechanism consisting of 26 steps and 17 species including the Zel'dovich NOx mechanism for the higher hydrocarbon fuel was implemented in the KIVA-3V. The characteristic time scale model was adopted to account for the effects of turbulent mixing on the reaction rates. The soot formation and oxidation processes are represented by Hiroyasu's model and NSC's model. The validation cases include the homogenous fuel/air mixture and the spray combustion in a constant volume chamber. After the validation, the present approach was applied to the analysis of the spray combustion processes in a HSDI diesel engine. The present approach reasonably well predicts the ignition delay, combustion processes, and emission characteristics in the high-pressure turbulent spray flame-field encountered in the practical HSDI diesel engines.

The Representative Interactive Flamelet(RIF) concept has been applied to numerically simulate the combustion processes and pollutant formation in the direct injection diesel engine. Due to the ability for interactively describing the transient behaviors of local flame structures with CFD solver, the RIF concept has the capabilities to predict the auto-ignition and subsequent flame propagation in the diesel engine combustion chamber as well as to effectively account for the detailed mechanisms of soot and NOx formation. In order to account for the spatial inhomogeneity of the scalar dissipation rate, the Eulerian Particle Flamelet Model using the multiple flamelets has been employed. Special emphasis is given to the turbulent combustion model which properly accounts for vaporization effects on turbulence-chemistry interaction.

Recently, high speed direct injection (HSDI) diesel engines are rapidly expanding their application to passenger cars and light duty commercial vehicles in western European market and other countries such as Korea and Japan. These movements are strongly backed by the technological innovations in the area of air charging and high pressure fuel injection systems. Variable geometry turbine (VGT) turbocharger, which could overcome the typical weak point of the existing turbocharged engine, and the common rail fuel injection system, which extended the flexibility of fuel injection capability, became two of the most frequently referred keywords in recent HSDI technology. In this paper some aspects of VGT potential as a full load torque and power modulator will be discussed. Possibility to utilize the portion of full load potential in favor of part load emissions and fuel economy will be investigated.

The air fuel ratio of current gasoline engine is mostly controlled by various air flow meters. When CVVT (Continuous Variable Valve Timing) device is applied to gasoline engine for higher engine performance, MAP (Manifold Absolute Pressure) sensor can not be applied anymore due to intake valve motion. Therefore HFM (Hot film airflow meter) is used for measuring the intake air flow instead of MAP sensor. Usually HFM has a little sensitivity in flow direction, therefore reverse flow from engine to air cleaner can not be measured. Also, HFM maker request enough straight duct length nearly 10 times of a duct diameter making a fully developed flow. But, most vehicles have no enough space to install such an intake system in engine room. Thus the inserted duct was applied to confirm the stable fully developed flow in air duct. The various duct configurations in front of HFM effect on the sensitivity of HFM.

This paper presents two closed-loop control methods for monitoring and improving the combustion behavior and the combustion noise on two 4-cylinder diesel engines, in which an in-cylinder pressure and an accelerometer transducer are used to monitor and control them. Combustion processes are developed to satisfy the stricter and stricter regulations on emissions and fuel consumption. These combustion processes are influenced by the factors such as engine durability, driving conditions, environmental influences and fuel properties. Combustion noise could be increased by these factors and is detrimental to interior sound quality. Therefore, it is necessary to develop robust combustion behaviors and combustion noise. For this situation, we have developed two closed-loop control methods. Firstly, a method using in-cylinder pressure data was developed for monitoring and improving the combustion noise of a 1.7L engine. A new index using the values calculated from the data was proposed.

This paper presents a transient vibration analysis of a nonlinear full-vehicle. The full-vehicle model consists of a powertrain, a trimmed body, a drive line, and front and rear suspensions with tires. It is driven by combustion forces and runs on a road surface. By performing time-domain simulation, it is possible to capture nonlinear behavior of a vehicle such as preload due to gravitational force, large deformation, and material nonlinearity which cannot be properly treated in the conventional steady state analysis. In constructing a full-vehicle, validation process is essential. Validation process is applied with respect to the assembling sequence. The validation starts with component levels such as tires, springs, shock absorbers, and a powertrain, and then the full-vehicle model is constructed. Model validation is done in two aspects; one is model accuracy and the other is model efficiency.