Search Results

Automotive floor carpet serves the purpose of insulating airborne noises like road-tire noise, transmission noise, fuel pump noise etc. Most commonly used automotive floor carpet structure is- molded sound barrier (PE, vinyl etc.) decoupled from the floor pan with an absorber such as felt. With increasing customer expectations and fuel efficiency requirements, the NVH requirements are increasing as well. The only possible way of increasing acoustic performance (Specifically, Sound Transmission Loss, STL) in the mentioned carpet structure is to increase the barrier material. This solution, however, comes at a great weight penalty. Theoretically, increasing the number of decoupled barrier layers greatly enhances the STL performance of an acoustic packaging for same weight. In practice, however, this solution presents problems like- ineffectiveness at lower frequencies, sudden dip in performance at modal frequencies.

In order to meet the challenges of future CAFE regulations & pollutant emission, vehicle fuel efficiency must be improved upon without compromising vehicle performance. Optimization of engine breathing & its impact on vehicle level fuel economy, performance needs balance between conflicting requirements of vehicle Fuel Economy, performance & drivability. In this study a Port Fuel Injection, naturally aspirated small passenger car gasoline engine was selected which was being used in a typical small passenger car. Simulation approach was used to investigate vehicle fuel economy and performance, where-in 1D CFD Engine model was used to investigate and optimize Valve train events (Intake and exhaust valve open and close timings) for best fuel economy. Engine Simulation software is physics based and uses a phenomenological approach 0-D turbulent combustion model to calculate engine performance parameters. Engine simulation model was calibrated within 95% accuracy of test data.

Gearbox power transfer efficiency is a major factor in overall powertrain efficiency of a passenger vehicle. With rapidly changing emission and fuel efficiency regulations, there is a push to increase the gearbox efficiency to improve the overall fuel economy of the vehicle. In case of an existing gearbox, efficiency can be improved by using the low viscosity lubrication oil. Despite a benefit in increasing the gearbox efficiency, lowering down the viscosity of lubrication oil gives rise to few challenges with respect to its performance. One of these challenges is breather performance which defines that transmission oil should not come out of breather pipe in some pre-defined conditions during gearbox operation. As this validation is being carried out on proto parts when the complete system is ready, failure to satisfy the defined criteria for breather performance can lead to multiple trials.

Vehicle cabin comfort emphasizes a specific image of a brand and its product quality. Low frequency powertrain induced noise and vibration levels are a major contributor affecting comfort inside passenger cabin. Thus, using hydraulic mount is a natural choice. Introduction of lighter body panels coupled with cost effective hydraulic mounts has resulted in some additional noises on rough road surfaces which are challenging to identify during design phase. This paper presents a novel approach to identify two such noises i.e. Cavitation noise and Mount membrane hitting noise based on component level testing which are validated at vehicle experimentally. These noises are encountered at 20~30kmph on undulated road surfaces. Sound quality aspect of such noises is also studied to evaluate the solution effectiveness.

In recent years, worldwide automotive manufacturers have been continuously working in the research of suitable technical solutions to meet upcoming stringent Real Driving Emission (RDE) and Corporate Average Fuel Economy (CAFÉ) targets, as set by international regulatory authorities. Many technologies have been already developed, or are currently under study by automotive manufacturer for gasoline engines, to meet legislated targets. In-line with the above objective, there are many technologies available in the market to expand lambda 1 (λ=1) region by reducing fuel enrichment at high load-high revolutions per minute (RPM) by reducing exhaust gas temperature (for catalyst protection) for RDE regulation [1]. Integrated Exhaust Manifold (IEM) is the key technology for the Internal Combustion (IC) for the subjected matter as catalyst durability protection is done by reducing exhaust gas temperatures instead of injecting excess fuel for cooling catalyst.

Rapidly changing emission and fuel efficiency regulations are pushing the design optimization boundaries further in the Indian car market which is already a very cost conscious. Fuel economy can be improved by reducing moving parts friction and weight optimization. Driveline or Transmission power losses are major factor in overall efficiency of rotating parts in a vehicle. Transmission efficiency can be improved by using low viscosity oil, reducing oil quantity and reducing churning losses in car transmission. Changes like low viscosity and reduced oil volume give rise to challenges like compromised lubrication and durability of rotating parts. This further leads to extended design cycles for launching new cars with better transmission efficiency and fuel economy into the market. Design cycle time can be reduced by using CFD simulation for oil flow validation in the early design stage.

In today’s Indian automotive industry, vehicles are becoming more complex and require more efforts to develop. Also, new and upcoming regulations demand more trials under varied driving conditions to ensuring robustness of emission control. Combined with expectations of customer to get new products more frequently, requires solutions and methods that can allow more trials with required accuracy to ensure compliance to stricter regulation and delivery a quality product. This translates into more trials in less time during the development life cycle. Recently, to overcome above challenge, there has been focus on simulating the vehicles trials in engine bench environment. ‘Road to Lab to Math’ (RLM) is a methodology to reduce the effort of On-road testing and replace it with laboratory testing and mathematical models. Also, on-road testing of prototype vehicles is expensive as it requires physical parts.

Continuously rising fuel prices and global concern on climate change have resulted in a need to deliver vehicles with increased fuel economy. This has to be achieved without compromising on performance, durability and cost. Passenger car manufacturers are looking at various ways to maximize fuel economy. Major part of fuel saving can be tapped from engine itself. This can be done by activities on engine as below: Improving overall combustion efficiency and hence BSFC Efficient thermal management. Weight reduction of engine parts or complete downsizing Hybridization. Reducing engine losses i.e. parasitic losses from auxiliaries and frictional losses. This paper is focused on the reduction of engine frictional losses (FMEP) through the use of low viscosity lubrication oils. Various factors in lubrication oil contribute to friction. Experimental approach to quantifying the effect of different parameters of lubrication oil on total engine friction is presented.

As the automotive market is very dynamic and vehicle manufactures try to reduce the vehicle development cycle time, more focus is being given to CAE simulation technologies to reduce the design cycle time and number of physical tests. CAE engineers are continuously working on improving the accuracy of CAE simulation, such as using flexible body dynamic simulation in place of linear static analysis. Strength calculation under dynamic condition is more accurate as compared to static condition as it gives more clear understanding of stress variation with motion, contacts and mass inertia. Failure has been observed in new development of valve train pivot screw under test conditions. As per linear static analysis, design was judged OK. Normal linear static analysis is a two stage process. In first stage loads are calculated by hand or peak loads are taken from multibody dynamics (MBD) rigid body analysis.

Hexavalent chromium Cr(VI) is recognized as a known human carcinogen via inhalation. This is banned to be used in Corrosion Protective Coatings as per End Life of Vehicle regulation (ELV) 2000/53/EC effective July'07 in EU. Traditionally all automotive metallic components which are Zinc plated are passivated with a thin Chromate layer to add to its brightness and protect it from premature corrosion. These Chromate coatings (or passivation) are generally Hexavalent chromium based and available in four grades: clear, yellow, olive drab, and black. Alternatives in the form of Trivalent Chromium Cr(III) are now available. By nature, both these passivations have different properties. Trivalent chromium has high temperature resistance but low wear resistance thus does not possess self healing properties. Also, its cost is significantly higher compared to hex chrome solutions.

Compressed natural gas (CNG) is being explored as a sustainable renewable fuel for vehicles in India due to mounting foreign exchange expenditure to import crude petroleum. Impending emissions regulations for diesel engines, specifically exhaust particulate emissions have caused engine manufacturers to once again examine the potential of alternative fuels. Much interest has centered on compressed natural gas (CNG) due to its potential for low particulate and hydrocarbon based emissions. Natural gas engine development projects have tended toward the use of current gasoline engine technology (stoichiometric mixtures, closed-loop fuel control and exhaust catalysts). Significant amount of research and development work is being undertaken in India to investigate various aspects of CNG utilization in different types of engines. This paper discusses about the development of the bi-fuel CNG engine for passenger vehicular application.

Plastic plays a major role in automotive interiors. Till now most of the Indian automobile industries are using plastics mainly to cover the bare sheet metal panels and to reduce the weight of the vehicle along with safety concerns. Eventually Indian customer requirement is changing towards luxury vehicles. Premium look and luxury feel of the vehicle plays an equal role along with fuel economy and cost. Interior cabin is the place where aesthetics and comfort is the key to attract customers. Door Trims are one of the major areas of interiors where one can be able to provide premium feeling to the customer by giving PVC skin and decorative inserts. This paper deals with different types of PVC skins and its properties based on process constraints, complexity of the inserts. Door trim inserts can be manufactured by various methods like adhesive pasting, thermo-compression molding and low pressure injection molding process etc.

Automobile industry is shifting its focus from conventional fuel vehicles to NexGen vehicles. The NexGen vehicles have electrical components to propel the vehicle apart from mechanical system. These vehicles have a goal of achieving better fuel efficiency along with reduced emissions making it customer as well as environment friendly. Idle start-stop is a key feature of NexGen vehicles, where, the Engine ECU switches to engine stop mode while idling to cut the fuel consumption and increase fuel efficiency. Engine restarts when there is an input from driver to run the vehicle. There is always a clash between the Engine ECU and automatic climate control unit (Auto-AC) either to enter idle stop mode for better fuel efficiency or inhibit idle stop mode to keep the compressor running for driver comfort. This clash can be resolved in two ways: 1 Hardware change and, 2 Software change Hardware change leads to increase in cost, validation effort and time.

Vehicle Hood being the face of a passenger car poses the challenge to meet the regulatory and aesthetic requirements. Urge to make a saleable product makes aesthetics a primary condition. This eventually makes the role of structure optimization much more important. Pedestrian protection- a recent development in the Indian automotive industry, known for dynamics of cost competitive cars, has posed the challenge to make passenger cars meeting the regulation at minimal cost. The paper demonstrates structure optimization of hood and design of peripheral parts for meeting pedestrian protection performance keeping the focus on low cost of ownership. The paper discusses development of an in-house methodology for meeting Headform compliance of a flagship model of Maruti Suzuki India Ltd., providing detailed analysis of the procedure followed from introduction stage of regulatory requirement in the project to final validation of the engineering intent.

In developing countries steel wheel is generally used in the low end passenger cars. Steel wheel has a hole at center, known as wheel bore which give the provision for tightening & un-tightening of axle nut. Due to this hole, the surrounding parts are visible which reduces the aesthetic appearance of the wheel. To cover the center portion of the wheel, “Cap, Wheel Center” also called as “Center Cap” is used, which is an aesthetic oriented part as shown in Figure 1. Center Cap is designed in such a manner that it can be easily removed & re-fitted during the service of vehicle. This paper explains the systematic methodology to optimize the weight of the “Center Cap” without compromising the performance & aesthetic appearance. Various analytical calculations have been done to achieve base line value of the design which was further justified using CAE (computer aided engineering) to optimize the performance & weight.

Downsizing of engines is becoming more popular as manufacturers toil for increased fuel economy. Due to the downsizing of engines, Brake Mean Effective Pressure (BMEP) tends to increase, which in turn increases the heat release from engine. This necessitates the need for optimizing cooling system in order to get higher engine output and lower emissions to comply with stringent emission norms. In earlier engines, thermo-siphon principle was used with water as the coolant. This has been replaced in modern engines with pressurized cooling system with coolants like ethylene glycol mix. Along with the conventional objective of increased material durability with the optimized engine cooling system, it has been found that there is an improvement in the engine output due to increased charging efficiency. This paper describes the effect of engine coolant temperature on performance, emission and efficiency of a three-cylinder naturally aspirated spark ignited engine.

Single body architecture designed for various global markets and subjected to varied load cases is a challenge for Body in White (BIW) engineers. Optimization of structural design to meet regulatory, insurance and assessment requirements is an iterative and time consuming task. With focus on reduction of vehicle's damageability and ease of repairability Original Equipment Manufactures (OEM), insurance companies and Research Council for Automobile Repairs (RCAR) [1] are striving for better designs. A space constraint crash box structure installed behind the bumper plays a significant role in absorption of energy, before transmitting to longitudinal rails. In this study, crashworthiness of a multipurpose crash box for a hatch segment vehicle is presented with the various design of experiments conducted with a focus on light weighting, cost and ease of manufacturing.

In automotive seating system, seat upholstery quality has an important role in defining the overall quality and aesthetics of vehicle interiors. Technical textiles for seating system used in automotive applications are generally categorized into woven or knitted type. An automotive textile material is a composite material made up of three layers; base fabric (top layer), foam (middle layer) and scrim (bottom layer) as shown in Fig. 1. There are many challenges to be overcome during development of fabric e.g. mechanical, physical and aesthetic issues have an impact on overall seat quality, appearance and performance. These issues get highlighted during testing, which takes place during development stage of fabric. The concerns mentioned above are found in automotive textiles in both woven and knitted types of fabrics sourced from different manufacturing set-ups. This paper focuses on identification of problems during testing, followed by root cause analysis.

This article brings a practical analysis for determination of gravity center in unsymmetrical three dimensional bodies practically and graphically. The gravitational center of an object is the point from which if suspended, the object remains stable at all times, this is also called as center of mass of the object, or the theoretical point at which the entire weight of the object is assumed to be concentrated. In certain tests, the Center of Gravity (CG) of the Seat is required to be known, for load application. The CG is the point at which a SEAT would balance if it were possible to suspend it at that point. This paper deals with use of applied engineering and theoretical calculations to ascertain the CG of First and Second Row seats (individual and bench type). In this case the center of gravity location is expressed in units of length along each of three axes (X, Y and Z). Load balance equation is used to calculate the CG of the seat.

Computational Fluid Dynamics (CFD) is used extensively in the optimization of modern passenger car to meet the ever growing need of higher fuel economy, better engine and underbody cooling. One of the way to achieve better fuel economy is to reduce the vehicle overall resistance to flow, know as drag. Vehicle drag is a complex phenomenon governed by vehicle styling, component shape, layout and driving velocity and road conditions. To reduce the drag a lot of aero-parts are used these days such as air-dam, skirts, spoiler, undercover, dams etc. However the design of these aero-parts must be optimized to get the desired result as their addition alone does not guarantee improvement in performance. This paper aims at studying the effect of air-dam height and position on vehicle aerodynamics. Also the effect of air-dam addition was verified using fuel economy simulations.