Refine Your Search

Topic

Author

Search Results

Technical Paper

Design Features of the JUNKERS 211B AIRCRAFT ENGINE

1942-01-01
420123
THE Junkers 211B engine follows the usual German practice of very large displacements and conservative mean effective pressures and rotative speeds. However, the relative light weight per unit of displacement results in a net weight per horsepower that is not far above its competitors. Fully automatic devices which control propeller speed, manifold pressure, mixture ratio, spark advance, and supercharger gear ratio follow the German policy of removing all possible distractions from the pilot. This is one of three large liquid-cooled engines known to be produced in quantity in Germany; it powers an impressive percentage of the Luftwaffe. While of external appearance and displacement that resemble the Daimler-Benz DB-601 engine, the fundamental construction, detail design practice, and metallurgy of the Junkers 211B are surprisingly different.
Technical Paper

The New PLYMOUTH Engine

1956-01-01
560019
PLYMOUTH'S new V-8 engine has a specific output of 0.65 bhp/cu in. and 145-psi bmep — obtained through a combination of high thermal, volumetric, and mechanical efficiencies. Good design, the author points out, has achieved this high output despite the dual-venturi carburetor and the 7.6/1 compression ratio, selected for satisfactory operation on regular-grade fuels. The engine has a bore and stroke of 3.563 × 3¼, weighs 568 lb without flywheel, is 29⅜ in. long, and is designed for optimum response to future compression ratio increases. (A report of oral discussion following presentation of this paper appears on p. 220, following “The New Packard V-8 Engine,” by W. E. Schwieder.)
Technical Paper

Considerations Affecting the Life of Automotive Camshafts and Tappets

1956-01-01
560015
WORK done in a development program relative to camshafts and tappets in the design of the Chrysler overhead-valve V-8 engine is described. The types of failure encountered are categorized as wear, scuffing, and fatigue. An accelerated test procedure was designed to promote early cam-tappet failures, and the development work was predicated upon the results obtained therefrom. Among the variables affecting the failure conditions, major emphasis was placed on material development. Specifically, the greater amount of time was spent in determining the optimum tappet material, while some time was devoted to the camshaft material. A combination of adjusted chemical composition and heat-treatment of hardenable cast iron for camshaft and tappets provided the best solution to the failure problems.
Technical Paper

Development Highlights and Unique Features of New Chrysler V-8 Engine

1951-01-01
510196
THE design and development of the new valve-in-head V-8 Chrysler engine of 7.5 compression ratio are described here. Among the features discussed by the authors are: the hemispherical combustion chamber, V-8 cylinder arrangement, double-breaker distributor, “thermal flywheel” on automatic choke, and exhaust-heated and water-jacketed throttle bodies. The hemispherical combustion chamber was adopted after it had displayed excellent volumetric and indicated thermal efficiencies, and an ability to maintain these high efficiencies in service. The high volumetric efficiency, for example, is considered to be due to such design features as valves not crowded together, nor surrounded closely by the combustion-chamber walls. They are thereby fully effective in the flow of the fuel-air mixture and the exhaust gases. The authors also present performance data for this engine, which, at full throttle, develops 180 hp at 4000 rpm and 312 ft-lb of torque at 2000 rpm.
Technical Paper

PRINCIPLES OF NOISE REDUCTION

1958-01-01
580052
THIS paper explains a few of the basic principles of the character of sound and the mechanism of human hearing. The author describes some simple experiments which demonstrate the relationship between intensity and loudness and the nature of harmony. He also points out the difficulties of accurately analyzing sound electronically, and the resulting importance of combining the finest electronic equipment with sharp, attentive human faculties. Five basic ways to reduce noise and the mechanics of each are described. The effect of these methods on the work of the sound engineer is indicated.
Technical Paper

Effect of Valve-Cam Ramps on Valve Train Dynamics

1999-03-01
1999-01-0801
Testing of an OHC valve train with hydraulic lash adjuster in which the valve displacements, velocities and accelerations were measured and analyzed in both time and frequency domains, coupled with analysis of the frequency content of the valve acceleration function and its ramps, show that traditional designs of the opening and closing ramps used on some IC engine valve cams can exacerbate vibration in the follower system causing higher levels of spring surge and noise. Suggestions are made for improvement to the design of the beginning and ending transitions of valve motion which can potentially reduce dynamic oscillation and vibration in the follower train.
Technical Paper

Can the k-ε Model Withstand the Challenges Posed by Complex Industrial Flows?

1997-04-08
971516
The purpose of this paper is to present numerical solution for three-dimensional flow about rotating short cylinders using the computer program AIRFLO3D. The flow Reynolds number was kept at 106 for all computations. The drag forces on the cylinder were obtained for different rotational speeds. Predictions were obtained for both an isolated cylinder and a cylinder on a moving ground. The standard k-ε model was employed to model the turbulence. Computed drag coefficients agreed well with the previous experimental data up to a spin ratio (=rω/V) of 1.5.
Technical Paper

An Evaluation of Turbulent Kinetic Energy for the In-Cylinder Flow of a Four-Valve 3.5L SI Engine Using 3-D LDV Measurements

1997-02-24
970793
A better understanding of turbulent kinetic energy is important for improvement of fuel-air mixing, which can lead to lower emissions and reduced fuel consumption. An in-cylinder flow study was conducted using 1548 Laser Doppler Velocimetry (LDV) measurements inside one cylinder of a 3.5L four-valve engine. The measurement method, which simultaneously collects three-dimensional velocity data through a quartz cylinder, allowed a volumetric evaluation of turbulent kinetic energy (TKE) inside an automotive engine. The results were animated on a UNIX workstation, using a 3D wireframe model. The data visualization software allowed the computation of TKE isosurfaces, and identified regions of higher turbulence within the cylinder. The mean velocity fields created complex flow patterns with symmetries about the center plane between the two intake valves. High levels of TKE were found in regions of high shear flow, attributed to the collisions of intake flows.
Technical Paper

Static and Dynamic Dent Resistance Performance of Automotive Steel Body Panels

1997-02-24
970158
In recent years, strict weight reduction targets have pushed auto manufacturers to use lighter gauge sheet steels in all areas of the vehicle including exterior body panels. As sheet metal thicknesses are reduced, dentability of body panels becomes of increasing concern. Thus, the goal becomes one of reducing sheet metal thickness while maintaining acceptable dent resistance. Most prior work in this area has focused on quasi-static loading conditions. In this study, both quasi-static and dynamic dent tests are evaluated. Fully assembled doors made from mild, medium strength bake hardenable and non-bake hardenable steels are examined. The quasi-static dent test is run at a test speed of 0.1 m/minute while the dynamic dent test is run at a test speed of 26.8 m/minute. Dynamic dent testing is of interest because it more closely approximates real life denting conditions such as in-plant handling and transit damage, and parking lot damage from car door and shopping cart impact.
Technical Paper

Application of Induction Heating in Automotive Production

1935-01-01
350121
INDUCTION heating is a process or method by which metal parts are heated by simply placing them in an alternating magnetic field. The action is that of the transformer, whereby electrical energy is transferred or passed over to another isolated electric or secondary circuit by means of the magnetic field; thus, no physical attachments or electrical contacts are necessary to have electrical currents, which are dissipated as heat, flow in the parts to be processed. The strength and frequency of the alternating magnetic field can be selected to produce any desired rate of heating and ultimate temperature. A circuit can be set up to dry lacquer at 160 deg. fahr. on thin sheet-metal parts or to melt in record time immense steel ingots. Induction heating is now commercially applied in automotive production to many processes, and these are specified.
Technical Paper

Determining Hardenability on Small Sizes

1941-01-01
410115
LIMITATIONS of the two general methods available for determining hardenability in steel, the authors point out, are that the test piece may not have a sufficient cross-section in which to develop the desired series of cooling rates, and that a special test piece (known as the L-type) must be machined for steels of low hardenability. The method using the Wuerfel bomb described in their paper, they explain, is directed primarily toward removal of these two limitations. Stated in terms of the critical diameter, they report that the results of the method are reproducible within ⅛ in.
Technical Paper

A Comparison of Aluminum, Sheet Molding Compound and Steel for Hoods

1992-02-01
920242
A unique opportunity arose to make a direct comparison of aluminum, sheet molding compound (SMC) and steel using a common hood design. In considering all possible material combinations of inner and outer panels, it was discovered that some of the combinations were incompatible due to material properties. Only the compatible material combinations were considered. Three different joining techniques - welding, bonding and bonded hem flanging - were evaluated. The cost, weight and structural performance of the chosen hood material combinations were established. Areas of further development were identified, including design optimization for specific material combinations.
Technical Paper

Improvements in the Dent Resistance of Steel Body Panels

1992-02-01
920243
A computer-controlled body panel testing machine has been used to quantify stiffness and dent resistance of body panels at Chrysler. The influence of yield strength and local reinforcement on the mechanical behavior of automotive door panels has been investigated. Medium strength steels in the range of 210 -240 MPa yield strength have produced significant improvements in dent resistance over a 160 MPa yield strength steel. Considerable improvements in dent resistance can also be attributed to the use of local, adhesively attached, glass fiber reinforcement patches. The effects of boundary conditions and panel shape on stiffness and dent resistance are illustrated in this application.
Technical Paper

Changes in Reliability During the Design and Development Process of a Vehicle's Electrical/Electronic Systems

1995-02-01
950826
The changes in reliability of the Electrical/Electronic Systems of a vehicle-line during its early design and development engineering processes have been studied. A computerized vehicle failure tracking system was used to provide results from several stages of early development vehicle testing at the proving grounds. The data were analyzed using a software program that assumes that failures in a repairable system, such as a car, occur as a nonhomogeneous Poisson process. Results suggest that, under normal circumstances, a significant and quantitative improvement in reliability is achievable as the system or component design progresses through the early design and development processes. This also provides a means of predicting future system(s) reliability when the system(s) is in production.
Technical Paper

Experimental and Computer Simulation Analysis of Transients on an Automobile Communication Bus

1995-02-01
950038
Voltage and current surges are a major concern when it comes to ensuring the functional integrity of electrical and electronic components and modules in an automobile system. This paper presents a computer simulation study for analyzing the effect of high voltage spikes and current load dump on a new Integrated Driver/Receiver (IDR) IC, currently being developed for a J1850 Data Communication Bus in an automobile. It describes the modeling and simulation of the protection structure proposed for the device. The simulation study yields a prediction of current and voltage capability of the protection circuit based on thermal breakdown and transient responses of the circuit. Two levels of modeling, namely, the behavioral level model and the component level model, are used to generate the simulation results. Experimental data will be acquired and used to validate the simulation model when the actual device becomes available.
Technical Paper

Network I/O and System Considerations

1995-02-01
950036
The J1850 bus requirements promote an unique and well characterized physical layer behavior developed through the learning curve of previous multiplex solutions. Design requirements such as: 1) Reliably interconnecting all of the vehicle's most complex modules, 2) Consistently withstanding the vehicle's harsh environment, and 3) Meeting SAE's functionality requirements, were all a formidable task to achieve. This paper will highlight the path taken to achieve a J1850 Bus interface which successfully met all of the design and functional goals. Chrysler's C2D insights will be discussed and related to goals for J1850. Other design considerations will also be discussed such as EMC issues, custom test equipment, and vehicle and component testability. In turn, silicon processes with special structures and topologies will be discussed relating the specific design with the needed electrical behavior. The HIP7020 J1850 BUS TRANSCEIVER I/O for MULTIPLEX WIRING accomplishes these requirements.
Technical Paper

OPNET J1850 Network Simulator

1995-02-01
950037
MIL 3's OPNET simulator was used to model Chrysler's J1850 bus. Modeled were both J1850 bus characteristics and those portions of control modules (e.g., the engine controller) which communicate on the bus. Current Chrysler control module algorithms and proposed Chrysler J1850 message formats were used to design the control module models. The control module models include all messages which are transmitted at fixed intervals over the J1850 bus. The effects of function-based messages (e.g., messages to be transmitted on a particular sensor or push-button reading) on system load were investigated by transmitting an additional message with a fixed, relatively high priority at 50 millisecond intervals.
Technical Paper

Architecture and Operation of the HIP7010 J1850 Byte-Level Interface Circuit

1995-02-01
950035
As a cost effective solution to making microcontroller based systems “J1850[1] aware”, a peripheral device (the HIP7010) was developed to extend the capabilities of standard microcontrollers. From the perspective of the Host, the peripheral device handles J1850 messages as a series of bytes (similar in concept to a universal asynchronous receiver/transmitter [UART]). The architecture of the HIP7010 is discussed. The design of the J1850 interface, state machine, status/control blocks, cyclical redundancy check (CRC) hardware, host interface, and fail-safe features are detailed. Illustrations are provided of: Host/HIP7010 interfacing; message transmission and reception; error handling; and In-Frame Response (IFR) generation.
Technical Paper

Chrysler 8.0-Liter V-10 Engine

1993-11-01
933033
Chrysler Corporation has developed an 8.0-liter engine for light truck applications. Numerous features combine to produce the highest power and torque ratings of any gasoline-fueled light truck engine currently available while also providing commensurate durability. These features include: a deep-skirt ten-cylinder 90° “V” block, a Helmholtz resonator intake manifold that enhances both low and mid-range torque, light die cast all-aluminum pistons for low vibration, a unique firing order for smooth operation, a “Y” block configuration for strength and durability, a heavy duty truck-type thermostat to control warm up, and a direct ignition system.
Technical Paper

Hydrogen Embrittlement in Automotive Fastener Applications

1996-02-01
960312
Fastener failure due to hydrogen embrittlement is of significant concern in the automotive industry. These types of failures occur unexpectedly. They may be very costly to the automotive company and fastener supplier, not only monetarily, but also in terms of customer satisfaction and safety. This paper is an overview of a program which one automotive company initiated to minimize hydrogen embrittlement in fasteners. The objectives of the program were two-fold. One was to obtain a better understanding of the hydrogen embrittlement phenomena as it relates to automotive fastener materials and processes. The second and most important objective, was to eliminate hydrogen embrittlement failures in vehicles. Early program efforts concentrated on a review of fastener applications and corrosion protection systems to optimize coated fasteners for hydrogen embrittlement resistance.
X