Search Results

This paper describes the development and experimental validation of a Plug-in Hybrid Electric Vehicle (PHEV) dynamic simulator that enables development, testing, and calibration of a traction control strategy. EcoCAR 2 is a three-year competition between fifteen North American universities, sponsored by the Department of Energy and General Motors that challenges students to redesign a Chevrolet Malibu to have increased fuel economy and decreased emissions while maintaining safety, performance, and consumer acceptability. The dynamic model is developed specifically for the Ohio State University EcoCAR 2 Team vehicle with a series-parallel PHEV architecture. This architecture features, in the front of the vehicle, an ICE separated from an automated manual transmission with a clutch as well as an electric machine coupled via a belt directly to the input of the transmission. The rear powertrain features another electric machine coupled to a fixed ratio gearbox connected to the wheels.

The advent of the Hybrid III crash test dummy marked the beginning of biofidelic anthropomorphic test devices. During the development of its critical components, notably the head, neck, knee, and thorax, biomechanical cadaver test results were incorporated into the design. The result was a dummy that represented the 50th percentile male during idealized impacts. In order to achieve a more biofidelic response from the components, many exotic materials and unique designs were utilized. The thorax, for instance, incorporates a spring steel rib design laminated with a viscoelastic polymeric composite material to damp the response. This combination results in the proper hysteretic losses necessary to model the human thorax under impact loading conditions. The disadvantage of this design is that the damping material properties are highly sensitive to temperature. A variation of more than 5 degrees Fahrenheit dramatically affects the response of the thorax.

Predominant failure modes in the forming of sheet metal parts are wrinkling and tearing. Wrinkling may occur at the flange as well as in other areas of the drawn part and is generated by excessive compressive stresses that cause the sheet to buckle locally. Fracture occurs in a drawn material which is under excessive tensile stresses. For a given part and blank geometries, the major factors affecting the occurrence of defects in sheet metal parts are the blank holder force (BHF) and the blank holder pressure (BHP). These variables can be controlled to delay or completely eliminate wrinkling and fracture. Modern mechanical presses are equipped with hydraulic cushions and various advanced multi-point pressure control systems. Thus, the BHP can be adjusted over the periphery of the blank holder as a function of location and time (or press stroke).

A newly developed process allows the near-net shape fabrication of alumina/aluminum composite bodies via the immersion of a sacrificial oxide preform into a molten aluminum alloy bath. The resulting composite possesses an attractive range of properties for application in several automotive components. These properties include: high strength and stiffness, appreciable thermal and electrical conductivity, high strength at elevated temperatures, coefficient of thermal expansion of 10 X 10-6 C-1 and relative ease of machinability. Low cost fabrication renders this material/process ideal for components such as brake rotors and calipers, cylinder bore liners, piston components.

A new technique for measuring the friction coefficient between the punch and workpiece during sheet forming operations has been developed at the Ohio State University. Various materials, such as interstitial-free (IF) steel, high strength (HS) steel, an aluminum alloy (2008T4) and 70/30 brass, were tested under dry and oil lubrication conditions at different punch rates and process conditions. The results show that punch friction depends on the angle of wrap, which varies with punch stroke, and on the strain rate, which depends on punch velocity. The O.S.U. Friction Test is described and typical results are presented which verify the usefulness of the new procedure.

In sheet metal forming, drawbeads are often used to control uneven material flow which may cause defects such as wrinkles, fractures, surface distortion and springback. Appropriate setting and adjusting the drawbead force is one of the most important parameters in sheet forming process control. However, drawbead design and drawbead force adjustment still rely on trial-and-error procedures. This paper summarizes the guidelines in drawbead design, evaluates a number of mathematical models in estimating drawbead forces, and investigates the effects of sheet thickness, material properties, drawbead geometry and penetration on the drawbead force.

Many discrete tonal type noise and vibration problems in automotive systems and other physical structures require passive multi-layer visco-elastic damping treatments in mid to high frequency regimes. To address such issues, experimental modal analysis and dynamic finite element methods are suggested as suitable tools. Results are presented in terms of several test structures (four thin elastic beams, a thick elastic plate and an automotive brake pad) with free-free boundary conditions. Composite modal loss factors are measured and predicted for two different damping insulators consisting of adhesive, steel and coating combinations. Special attention is paid to the elastic deformation modes of test structures and spectral scaling of material properties for the finite element models.

For some vehicle dynamics applications, an estimate of a vehicle's center of gravity (cg) height and mass moments of inertia can suffice. For other applications, such as vehicle models and simulations used for vehicle development, these values should be as accurate as possible. This paper presents several topics related to inertial parameter estimation and measurement. The first is a simple but reliable method of estimating vehicle mass moment of inertia values from data such as the center of gravity height, roof height, track width, and other easily measurable values of any light road vehicle. The second is an error analysis showing the effect, during a simple static cg height test, of vehicle motion (relative to the support system) on the vehicle's calculated cg height. A method of accounting for this motion is presented. Similarly, the effects of vehicle motion are analyzed for subsequent mass moment of inertia tests.

In this paper, we propose an IC engine fuel system diagnostic algorithm based on a discrete-event nonlinear observer using the production oxygen sensor. A mean value engine model is used to describe the engine dynamics. A procedure for designing the discrete event based observer is presented and applied to estimate important engine variables using the measured binary oxygen sensor output. The estimated variables are then used to perform diagnostics of the fuel system of the IC engine. Experimental results on a multi-cylinder production engine are presented to demonstrate the effectiveness of the proposed method.

This paper describes the background and development of a program focused on motorsports engineering education currently in progress at the Ohio State University (OSU). An interdisciplinary curriculum, with the involvement of various engineering departments, is being proposed for development in an attempt to address some of the engineering education needs of the motorsports industry. The program described in this paper strives to provide engineering students with an interdisciplinary background race engineering, and also provides opportunities for motorsports oriented thesis projects. The paper briefly summarizes the key elements of the curriculum, and describes how the integration of course material from different disciplines with team work on student competition projects, possibly coupled with internships with racing teams, can provide an ideal setting for the education of a new generation of race engineers.

This paper presents an overview of the evolution of computer simulations in vehicle collision and occupant kinematic reconstructions. The basic principles behind these simulations, the origin of these programs and the evolution of these programs from a basic analytical mathematical model to a sophisticated computer program are discussed. In addition, a brief computer development history is discussed to demonstrate how the evolution of computer assisted vehicle accident reconstruction becomes feasible for a reconstructionist. Possible future research in computer reconstruction is also discussed.

The motivation of this paper is inverse estimation of the material properties for sheet metals subjected to cyclic loading. Cyclic three-point bending tests are performed. Bending moments are computed from the measured data, namely, punch stroke, punch load, bending strain and bending angle. Bending moments are also calculated based on the selected material model in which normal anisotropy and combined hardening are considered. Material parameters are identified by minimizing the difference between these two bending moments. Modified Levenberg-Marquardt method is used in the optimization procedure. Stress-strain curves are generated with the optimized material parameters.

Reported tensile and fatigue properties of die cast AZ91D and AM60B magnesium alloys indicate that those values depend on the size and shape of the test samples and their global porosities. This paper reviews the mechanical properties reported in the open literature for these die cast alloys and indicates that section thickness and global porosity are inadequate for predicting the tensile and fatigue properties of die cast AZ91D and AM60B magnesium alloys.

A computer simulation has been developed that models conventional, electric, and hybrid drivetrains. The vehicle's performance is predicted for a given driving cycle, such as the Federal Urban Driving Schedule (FUDS). This computer simulation was used in a massive designspace exploration to simulate 1.8 million different vehicles, including conventional, electric, and hybrid-electric vehicles (HEVs). This paper gives a description of the vehicle simulator as well as the results and implications of the large design-space exploration.