Refine Your Search

Topic

Author

Search Results

Technical Paper

Transient Clunk Response of a Driveline System: Laboratory Experiment and Analytical Studies

2007-05-15
2007-01-2233
A laboratory experiment is designed to examine the clunk phenomenon. A static torque is applied to a driveline system via the mass of an overhanging torsion bar and electromagnet. Then an applied load may be varied via attached mass and released to simulate the step down (tip-out) response of the system. Shaft torques and torsional and translational accelerations are recorded at pre-defined locations. The static torque closes up the driveline clearances in the pinion/ring (crown wheel) mesh. With release of the applied load the driveline undergoes transient vibration. Further, the ratio of preload to static load is adjusted to lead to either no-impact or impact events. Test A provides a ‘linear’ result where the contact stiffness does not pass into clearance. This test is used for confirming transient response and studying friction and damping. Test B is for mass release with sufficient applied torque to pass into clearance, allowing the study of the clunk.
Technical Paper

Effect of Viscoelastic Patch Damping on Casing Cover Dynamics

2001-04-30
2001-01-1463
Many automotive components and sub-systems require viscoelastic damping treatments to control noise and vibration characteristics. To aid the dynamic design process, new approaches are needed for modeling of partial damping treatments and characterization of the overall dynamic behavior. The analytical component of the design process is illustrated via the transmission casing cover, along with supporting experiments. First, the vibration response of production casing plates is examined, with and without the constrained layer treatment. A modified flat plate is employed along with a generic housing that provides the realistic boundary conditions for subsequent work. A simplified analytical damping model for constrained viscoelastic layer damping is suggested based on assumed modal functions. Using the analytical model, design guidelines in terms of optimal patch shapes and locations are suggested.
Technical Paper

Vibration Power Transmission Through Multi-Dimensional Isolation Paths Over High Frequencies

2001-04-30
2001-01-1452
In many vibration isolation problems, translational motion has been regarded as a major contributor to the energy transmitted from a source to a receiver. However, the rotational components of isolation paths must be incorporated as the frequency range of interest increases. This article focuses on the flexural motion of an elastomeric isolator but the longitudinal motion is also considered. In this study, the isolator is modeled using the Timoshenko beam theory (flexural motion) and the wave equation (longitudinal motion), and linear, time-invariant system assumption is made throughout this study. Two different frequency response characteristics of an elastomeric isolator are predicted by the Timoshenko beam theory and are compared with its subsets. A rigid body is employed for the source and the receiver is modeled using two alternate formulations: an infinite beam and then a finite beam. Power transmission efficiency concept is employed to quantify the isolation achieved.
Technical Paper

Vibro-Acoustic Effects of Friction in Gears: An Experimental Investigation

2001-04-30
2001-01-1516
Amongst various sources of noise and vibrations in gear meshing, transmission error and sliding friction between the teeth are two major constituents. As the operating conditions are altered, the magnitude of these two excitations is affected differently and either of them can become the dominant factor. In this article, an experimental investigation is presented for identifying the friction excitation and to study the influence of tribological parameters on the radiated sound. Since both friction and transmission error excitations occur at the same fundamental period of one meshing cycle, they result in similar spectral contents in the dynamic response. Hence specific methods like the variation of parameters are designed in order to distinguish between the individual vibration and noise sources. The two main tribological parameters that are varied are the lubricant and the surface finish characteristics of gear teeth.
Technical Paper

Refinements of a Heavy Truck ABS Model

2007-04-16
2007-01-0839
In 2004, a model of a 6s6m ABS controller was developed in order to support NHTSA's efforts in the study of heavy truck braking performance. This model was developed using Simulink and interfaced with TruckSim, a vehicle dynamics software package, in order to create an accurate braking simulation of a 6×4 Peterbilt straight truck. For this study, the vehicle model braking dynamics were improved and the ABS controller model was refined. Also, the controller was made adaptable to ABS configurations other than 6s6m, such as 4s4m and 4s3m. Controller models were finally validated to experimental data from the Peterbilt truck, gathered at NHTSA's Vehicle Research and Test Center (VRTC).
Technical Paper

Development and Implementation of a Path-Following Algorithm for an Autonomous Vehicle

2007-04-16
2007-01-0815
This paper describes the development and implementation of an accurate and repeatable path-following algorithm focused ultimately on vehicle testing. A compact, lightweight, and portable hardware package allows easy installation and negligible impact on the vehicle mass, even for the smallest automobile. Innovative features include the ability to generate a smooth, evenly-spaced path vector regardless the quality of the given path. The algorithm proposed in this work is suitable for testing in a controlled environment. The system was evaluated in simulation and performed well in road tests at low speeds.
Technical Paper

Effects of ABS Controller Parameters on Heavy Truck Model Braking Performance

2006-10-31
2006-01-3482
This paper covers research conducted at the National Highway Traffic Safety Administration's Vehicle Research and Test Center (VRTC) examining the performance of semitrailer anti-lock braking systems (ABS). For this study, a vehicle dynamics model was constructed for the combination of a 4×2 tractor and a 48-foot trailer, using TruckSim. ABS models for the tractor and trailer, as well as brake dynamics and surface friction models, were created in Simulink so that the effect of varying ABS controller parameters and configurations on semitrailer braking performance could be studied under extreme braking maneuvers. The longitudinal and lateral performances of this tractor-trailer model were examined for a variety of different trailer ABS controller models, including the 2s1m, 4s2m, and 4s4m configurations. Also, alternative controllers of the same configuration were studied by varying the parameters of the 2s1m controller.
Technical Paper

Design of a Hybrid Exhaust Silencing System for a Production Engine

2005-05-16
2005-01-2349
A prototype hybrid exhaust silencing system consisting of dissipative and reactive components is designed based on the boundary element method (BEM) with a specific emphasis on its acoustic performance as evaluated relative to a production system. The outer dimensions of the prototype system are comparable to its production counterpart, which has two silencers connected by a pipe. The predicted transmission loss by BEM for the prototype is compared with the experimental results in an impedance tube for both the prototype and production hardware, providing a design guidance for the former. The sound pressure levels measured at the tailpipe exit during the engine ramp-up experiments in a dynamometer laboratory are presented to compare the two systems, providing the final assessment.
Technical Paper

Nonlinear Modeling of an Electromagnetic Valve Actuator

2006-04-03
2006-01-0043
This paper presents the modeling of an Electromagnetic Valve Actuator (EMV). A nonlinear model is formulated and presented that takes into account secondary nonlinearities like hysteresis, saturation, bounce and mutual inductance. The uniqueness of the model is contained in the method used in modeling hysteresis, saturation and mutual inductance. Theoretical and experimental methods for identifying parameters of the model are presented. The nonlinear model is experimentally validated. Simulation and experimental results are presented for an EMV designed and built in our laboratory. The experimental results show that sensorless estimation could be a possible solution for position control.
Technical Paper

The Development of a Heavy Truck ABS Model

2005-04-11
2005-01-0413
This paper discusses the improvement of a heavy truck anti-lock brake system (ABS) model currently used by the National Highway Traffic Safety Administration (NHTSA) in conjunction with multibody vehicle dynamics software. Accurate modeling of this complex system is paramount in predicting real-world dynamics, and significant improvements in model accuracy are now possible due to recent access to ABS system data during on-track experimental testing. This paper focuses on improving an existing ABS model to accurately simulate braking under limit braking maneuvers on high and low-coefficient surfaces. To accomplish this, an ABS controller model with slip ratio and wheel acceleration thresholds was developed to handle these scenarios. The model was verified through testing of a Class VIII 6×4 straight truck. The Simulink brake system and ABS model both run simultaneously with TruckSim, with the initialization and results being acquired through Matlab.
Technical Paper

Experimental Evaluation of Fishhook Maneuver Performance of a Kinetic Suspension System

2005-04-11
2005-01-0392
Kinetic Pty Ltd and Tenneco Automotive have developed a passive suspension system called a Kinetic system. The motivation for the design of the system is discussed, and the function of the system is explained. The system improves handling, stability, and ride by passively decoupling roll stiffness from articulation stiffness and roll damping from bounce damping. Improved stability is evaluated by conducting NHTSA's Roll Rate Feedback Fishhook tests on a small SUV equipped with the Kinetic system. Results of the testing are presented, and benefits to rollover are discussed.
Technical Paper

Integration of an Adaptive Control Strategy on an Automated Steering Controller

2005-04-11
2005-01-0393
This paper describes an adaptive control strategy for improving the steering response of an automated vehicle steering controller. In order to achieve repeatable dynamic test results, precise steering inputs are necessary. This strategy provides the controller tuning parameters optimized for a particular vehicle's steering system. Having the capability to adaptively tune the steering controller for any vehicle installation provides an easy method for obtaining precise steering inputs for a wide range of vehicles, from small off-road utility vehicles to passenger vehicles to heavy trucks. The S.E.A. Ltd. Automated Steering Controller (ASC) is used exclusively in conducting this research. By recording the torque input to the steering system by the steering controller and the resulting steering angle during only a single test, the ASC is able to characterize the steering system of the test vehicle and create a computer model with appropriate parameters.
Technical Paper

Design and Conduct of Precision Planetary Gear Vibration Experiments

2009-05-19
2009-01-2071
Despite a large body of analytical work characterizing the dynamic motion of planetary gears, supporting experimental data is limited. Experimental results are needed to support computer modeling and offer practical optimization guidelines to gear designers. This paper presents the design and implementation of a test facility and precision test fixtures for accurate measurement of planetary gear vibration at operating conditions. Acceleration measurements are made on all planetary bodies under controlled torque/speed conditions. Custom, high-precision test fixtures accommodate instrumentation, ensure accurate alignment, help isolate gear dynamics, and allow for variability in future testing. Results are compared with finite element and lumped parameter models.
Technical Paper

Vehicle Dynamics Modeling and Validation for the 2003 Ford Expedition with ESC using ADAMS View

2009-04-20
2009-01-0453
The paper discusses the development of a model of the 2003 Ford Expedition using ADAMS View and its validation with experimental data. The front and rear suspensions are independent double A-arm type suspensions modeled using rigid links and ideal joints. The suspension springs and shock absorbers are modeled as force elements. The plots comparing the experimental tests and the simulation results are shown in this paper. Quasi-static roll and bounce tests are used to validate the suspension characteristics of the model while the Sine with Dwell and Slowly Increasing Steer maneuvers are used to validate the vehicle handling and tire-road interaction characteristics of the model. This paper also details the incorporation of an ESC model, originally developed by Kinjawadekar et al. [2] for CarSim, with the ADAMS model. The ESC is modeled in Simulink and co-simulated with the ADAMS vehicle model. Plots validating the ESC model with experimental data are also included.
Technical Paper

Repeatability and Bias Study on the Vehicle Inertia Measurement Facility (VIMF)

2009-04-20
2009-01-0447
Representative vehicle inertial characteristics are important parameters for the development of motor vehicles and the proper operation of on-board systems. The Vehicle Inertia Measurement Facility (VIMF) measures vehicle center of gravity location, principal moments of inertia, and the roll/yaw product of inertia. It is important to understand the VIMF’s accuracy and repeatability, as well as the underlying methodology and assumptions, when performing tests or using the results of the test. This study reports on a repeatability analysis performed at the lower and upper limits of the VIMF. Each test performed is a complete drive-on/drive-off test. The test sequence involves the repeatability evaluation of several different machine configurations. Ten complete tests are performed for each vehicle. To better address the possibility of measurement bias, the design and verification of a calibration fixture for inertial characteristics is presented.
Technical Paper

Dynamic Simulation of Nonlinear Model-Based Observer for Hydrodynamic Torque Converter System

2004-03-08
2004-01-1228
It is well-known that the hydrodynamic torque converter plays a major role in the transient study of power train systems since it has a great influence on the transient characteristics of a vehicle during gear shifting as well as vehicle launching. To predict accurately the vehicle characteristics, detailed analysis of the hydrodynamic torque converter is required. However, even with the development of a nonlinear dynamic model for the torque converter based on Hrovat and Tobler's paper (1985) is available, it is imperative to calculate both torques from impeller and turbine in order to utilize the dynamic model since it takes torque as an input [3]. In order to obtain the information about necessary but unmeasurable variables, nonlinear model-based estimator is developed using already available and measurable speeds data of impeller and turbine. The hydrodynamic torque converter model includes all necessary dynamics, namely, hydraulic as well as mechanical dynamics.
Technical Paper

Application of the Extended Kalman Filter to a Planar Vehicle Model to Predict the Onset of Jackknife Instability

2004-03-08
2004-01-1785
The widely used Extended Kalman Filter (EKF) is applied to a planar model of an articulated vehicle to predict jackknifing events. The states of hitch angle and hitch angle rate are estimated using a vehicle model and the available or “measured” states of lateral acceleration and yaw rate from the prime mover. Tuning, performance, and compromises for the EKF in this application are discussed. This application of the EKF is effective in predicting the onset of instability for an articulated vehicle under low-μ and low-load conditions. These conditions have been shown to be most likely to render heavy articulated vehicles vulnerable to jackknife instability. Options for model refinements are also presented.
Technical Paper

Delta-V, Barrier Equivalent Velocity and Acceleration Pulse of a Vehicle During an Impact

2005-04-11
2005-01-1187
Delta-V and Barrier Equivalent Velocity (BEV) are terms that have been used for many years to describe aspects of what happened to a vehicle when an impact occurred. That is, they are used to describe some physical change in the vehicle state before the impact as compared to after the impact. Specifically, the Delta-V describes the change in the vehicle velocity vector from just before the impact until just after the impact. The BEV attempts to quantify the energy required to cause the damage associated with an impact. In order to understand what happens to a vehicle and its occupants during an impact, it is necessary to examine the acceleration pulse undergone by the vehicle during the impact. The acceleration pulse describes, in detail, how the Delta-V occurs as a function of time, and is related with the deformation of the vehicle as well as the object contacted by the vehicle during an impact.
Technical Paper

Vehicle Characterization Through Pole Impact Testing, Part II: Analysis of Center and Offset Center Impacts

2005-04-11
2005-01-1186
The severity of an impact in terms of the acceleration in the occupant compartment is dependent not only on the change in vehicle velocity, but also the time for the change in velocity to occur. These depend on the geometry and stiffness of both the striking vehicle and struck object. In narrow-object frontal impacts, impact location can affect the shape and duration of the acceleration pulse that reaches the occupant compartment. In this paper, the frontal impact response of a full-sized pickup to 10 mile per hour and 20 mile per hour pole impacts at the centerline and at a location nearer the frame rails is compared using the acceleration pulse shape, the average acceleration in the occupant compartment, and the residual crush. A bilinear curve relating impact speed to residual crush is developed.
Technical Paper

Fabrication of a Parallel-Series PHEV for the EcoCAR 2 Competition

2013-10-14
2013-01-2491
The EcoCAR 2: Plugging into the Future team at the Ohio State University is designing a Parallel-Series Plug-in Hybrid Electric Vehicle capable of 50 miles of all-electric range. The vehicle features a 18.9-kWh lithium-ion battery pack with range extending operation in both series and parallel modes. This is made possible by a 1.8-L ethanol (E85) engine and 6-speed automated manual transmission. This vehicle is designed to drastically reduce fuel consumption, with a utility factor weighted fuel economy of 51 miles per gallon gasoline equivalent (mpgge), while meeting Tier II Bin 5 emissions standards. This report details the fabrication and control implementation process followed by the Ohio State team during Year 2 of the competition. The fabrication process includes finalizing designs based on identified requirements, building and assembling components, and performing extensive validation testing on the mechanical, electrical and control systems.
X