Refine Your Search

Topic

Search Results

Technical Paper

Power Matching and Control Strategy of Plug-in Series Hybrid Electric Car

2010-10-25
2010-01-2195
In this paper, based on the plug-in series hybrid electric vehicle development project, the vehicle technology solutions and the match of power system parameters were analyzed. The vehicle control strategies were identified and optimized according to plug-in hybrid vehicle features. The plug-in series hybrid, rule-based logic threshold switching control strategy, charge depleting (CD) mode and charge-sustaining (CS) mode are chosen according to the key factors, such as the environment, performance requirements, technical requirements and cost. And then the structure and model of vehicle control strategy were established to carry out vehicle energy management and power system control. The parameter selection, electric drive system matching, energy storage system design based on the requirement of vehicle performance, system architecture and control strategy are presented.
Technical Paper

Optimization of Control Strategy for Engine Start-stop in a Plug-in Series Hybrid Electric Vehicle

2010-10-25
2010-01-2214
Plug-in hybrid electric vehicles (PHEVs) provide significantly improvement in fuel economy over conventional vehicles as well as reductions in greenhouse gas and petroleum. Numerous recent reports regarding control strategy, power train configuration, driving pattern, all electric range (AER) and their effects on fuel consumption and electric energy consumption of PHEVs are reported. Meanwhile, the control strategy for engine start-stop and mileage between recharging events from the electricity grid also has an important influence on the petroleum displacement potential of PHEVs, but few reports are published. In this paper, a detailed simulation model is set up for a plug-in series hybrid electric vehicle (PSHEV) employing the AVL CRUISE. The model was employed to predict the AER of the baseline PSHEV using rule-based logical threshold switching control strategy.
Technical Paper

The Effect of High-Power Capacitive Spark Discharge on the Ignition and Flame Propagation in a Lean and Diluted Cylinder Charge

2016-04-05
2016-01-0707
Research studies have suggested that changes to the ignition system are required to generate a more robust flame kernel in order to secure the ignition process for the future advanced high efficiency spark-ignition (SI) engines. In a typical inductive ignition system, the spark discharge is initiated by a transient high-power electrical breakdown and sustained by a relatively low-power glow process. The electrical breakdown is characterized as a capacitive discharge process with a small quantity of energy coming mainly from the gap parasitic capacitor. Enhancement of the breakdown is a potential avenue effectively for extending the lean limit of SI engine. In this work, the effect of high-power capacitive spark discharge on the early flame kernel growth of premixed methane-air mixtures is investigated through electrical probing and optical diagnosis.
Technical Paper

STATE OF HEALTH DETERMINATION OF LITHIUM ION CELLS IN AND OUTSIDE THE VEHICLE

2011-05-17
2011-39-7235
There is an enormous effort to implement safety functionality into battery systems to prevent any accidents with the poisonous and inflammable ingredients of the electrolytes and electrode materials. But not only the safety regulation for lithium ion batteries will be different in comparison to the home electronics application, also the operating strategy must be different to guaranty the required lifetime in the automotive industry up to 10-12 years. This paperwork will show an approach to get offline (on test benches) and/or online (installed inside the car) information regarding the current healthy and state inside the cell. As an approach modeling of physical effects by the help of electro impedance spectroscopy (EIS) will be applied.
Technical Paper

UWB Location Algorithm Based on BP Neural Network

2018-08-07
2018-01-1605
In order to solve the problem that in the traditional trilateral positioning algorithm, the final positioning error is large when there is a certain error in the measured three-sided distance, a UWB positioning algorithm based on Back Propagation (BP) neural network is proposed. The algorithm utilizes the fast learning characteristic and the ability of approximating any non-linear mapping of neural network, and realizes the location of the mobile label through the TOA measurement value provided by the base station and the BP neural network. By comparing the traditional trilateral positioning algorithm, the BP neural network algorithm based on four distance inputs and the BP neural network algorithm based on four distance inputs with trilateral positioning coordinates, it can be seen that the positioning error of traditional trilateral positioning algorithm is 30 cm, and the positioning error of the positioning algorithm based on the BP neural network proposed in this paper is 10 cm.
Technical Paper

Camera-Radar Data Fusion for Target Detection via Kalman Filter and Bayesian Estimation

2018-08-07
2018-01-1608
Target detection is essential to the advanced driving assistance system (ADAS) and automatic driving. And the data fusion of millimeter wave radar and camera could provide more accurate and complete information of targets and enhance the environmental perception performance. In this paper, a method of vehicle and pedestrian detection based on the data fusion of millimeter wave radar and camera is proposed to improve the target distance estimation accuracy. The first step is the targets data acquisition. A deep learning model called Single Shot MultiBox Detector (SSD) is utilized for targets detection in consecutive video frames captured by camera and further optimized for high real-time performance and accuracy. Secondly, the coordinate system of camera and radar are unified by coordinate transformation matrix. Then, the parallel Kalman filter is used to track the targets detected by radar and camera respectively.
Technical Paper

Semantic Segmentation for Traffic Scene Understanding Based on Mobile Networks

2018-08-07
2018-01-1600
Real-time and reliable perception of the surrounding environment is an important prerequisite for advanced driving assistance system (ADAS) and automatic driving. And vision-based detection plays a significant role in environment perception for automatic vehicles. Although deep convolutional neural networks enable efficient recognition of various objects, it has difficulty in accurately detecting special vehicles, rocks, road pile, construction site, fence and so on. In this work, we address the task of traffic scene understanding with semantic image segmentation. Both driveable area and the classification of object can be attained from the segmentation result. First, we define 29 classes of objects in traffic scenarios with different labels and modify the Deeplab V2 network. Then in order to reduce the running time, MobileNet architecture is applied to generate the feature map instead of the original models.
Technical Paper

Research on Track Management of Multi-Target Tracking Based on Modified Fast Algorithm for Data Association

2018-08-07
2018-01-1619
With the development of autonomous vehicle technology, there is an increasing tendency toward the application of intelligent sensors in environment-perception system on autonomous vehicle to assist vehicle in intelligent decision making relevant to autonomous driving. As for environment-perception system, a good track management method serves as the foundation, while multi-target tracking and multi-sensor data fusion are recognized as the key. In this paper, a track management method is proposed to deal with multi-target tracking based on the target-level data of multisource environmental sensors for autonomous vehicle. The track management includes four procedures as following: track initiation; point-track association; track update; track deletion. A modified fast algorithm for data association is applied in the point-track association procedure. Afterwards Kalman filter is implemented to update the track information of target. The algorithm has got through a simulation test.
Technical Paper

A Localization System for Autonomous Driving: Global and Local Location Matching Based on Mono-SLAM

2018-08-07
2018-01-1610
The utilization of the SLAM (Simultaneous Localization and Mapping) technique was extended from the robotics to the autonomous vehicles for achieving the positioning. However, SLAM cannot obtain the global position of the vehicle but a relative one to the start. For sake of this, a fast and accurate system was proposed to obtain both the local position and the global position of vehicles based on mono-SLAM which realized the SLAM by using monocular camera with a lower cost and power consumption. Firstly, the rough latitude and longitude of current position was obtained by using common GPS without differential signal. Then, the Mono-SLAM operated on the consecutive video frames to generate the localization and local trajectory and its accuracy was further improved by utilizing the IMU information. After that, a piece of Map centered in the rough position obtained by common GPS was downloaded from the Open Street Map.
Technical Paper

System Design and Model of a 3D 79 GHz High Resolution Ultra-Wide Band Millimeter-Wave Imaging Automotive Radar

2018-08-07
2018-01-1615
Automotive radar is an important environment perception sensor for advance driving assistance system. It can detect objects around the vehicle with high accuracy and it works in all bad weathers. For traditional automotive radar, it cannot measure the objects’ height. Thus, a manhole cover on the road surface or a guideboard high above the road would be taken erroneously as a non-moving car. In such cases, the adaptive cruise system would decelerate or stop the vehicle erroneously and make the driver uncomfortable. A 3D automotive radar with two-dimensional electronic scanning can measure the targets’ height as well as the targets’ azimuth angle. This paper presents a 79 GHz ultra-wide band automotive 3D imaging radar. Due to the 4 GHz wide bandwidth, the range resolution of this radar can be as small as 3.75 cm.
Technical Paper

The System Identification for the Hydrostatic Drive System of Secondary Regulation Using Neural Networks

1996-10-01
962231
In this paper, the system identification theory and method using dynamic neural networks are presented, the multilayer feedforward networks employed, the backpropagation with adaptive learning rate algorithms proposed. Finally the comparision of network output with that of the hydrostatic drive system of secondary regulation is given, and output error, sum-squared error et al, or the results that embody the effect of system identification given sine input to it are provided.
Technical Paper

Whole Field Bonded Steel Tensile Test Using Digital Image Correlation System

2010-04-12
2010-01-0960
Adhesive bonding has many applications in the automotive industry. The single-lapped bonded joint is the most typically used among various bonding types. This paper presents experimental research for determining the strain field of the single-lapped joint under tensile loading. The materials for the joint are epoxy-based structural adhesive and low-carbon electrolytic zinc steel plate. In the study, a DIC (digital image correlation) system was adopted to measure the strain distribution of the bonded joint during a tensile test. The bonded steel coupons in the tensile test were prepared according to the ASTM standard. During the measurement, images of the coupon joint were taken before and after the deformation process. Then the DIC system measured the strain of bonded joint by comparing two consecutive images. The measured data from the DIC was compared to data taken simultaneously from a traditional extensometer.
Technical Paper

Simulations of Key Design Parameters and Performance Optimization for a Free-piston Engine

2010-04-12
2010-01-1105
To develop a free-piston engine-alternator integrative power system for Hybrid Electric Vehicles, the key design parameters, such as reciprocating mass of the piston assembly, compression ratio, the ignition timing, the engine fuel consumption rate and power output, are studied based on the simulation. The results show that, the system simulation model of the free piston engine can predict the in-cylinder pressure vs. the piston's displacement being accurate enough as the test results from reported reference. The model can be employed to optimize the design parameters and to predict the fuel economy and power output. It provides the methods and bases for the free piston engine design and predicting the main performance parameters' values.
Technical Paper

Transient Characteristics of Cold Start Emissions from a Two-Stage Direct Injection Gasoline Engines Employing the Total Stoichiometric Ratio and Local Rich Mixture Start-up Strategy

2012-04-16
2012-01-1068
To improve the cold start performance and to reduce the misfire occurrence at cold start, the start-up strategy of total stoichiometric ratio combined with local rich mixture was applied in the study. The effect of injection strategy (the 1st injection timing, 2nd injection timing, 1st and 2nd fuel injection proportion and ignition timing) on the cold start HC emissions in the initial 10 cycles were investigated in a Two stage direct injection (TSDI) gasoline engine. The transient HC and NO emissions in the initial 10 cycles were analyzed, when the fuels are injected in the only 1st cycle and in the followed all cycles. The transient misfiring HC emissions were compared between the single and two-stage injection modes. In addition, the unburned HC (UBHC) emissions in the 1st cycle are compared among the TSDI engine, Gasoline direct injection (GDI) engine, Port fuel injection (PFI) engine and Liquefied petroleum gaseous (LPG) engine at the stoichiometric ratio.
Technical Paper

A New Method of Target Detection Based on Autonomous Radar and Camera Data Fusion

2017-09-23
2017-01-1977
Vehicle and pedestrian detection technology is the most important part of advanced driving assistance system (ADAS) and automatic driving. The fusion of millimeter wave radar and camera is an important trend to enhance the environmental perception performance. In this paper, we propose a method of vehicle and pedestrian detection based on millimeter wave radar and camera. Moreover, the proposed method complete the detection of vehicle and pedestrian based on dynamic region generated by the radar data and sliding window. First, the radar target information is mapped to the image by means of coordinate transformation. Then by analyzing the scene, we obtain the sliding windows. Next, the sliding windows are detected by HOG features and SVM classifier in a rough detect. Then using the match function to confirm the target. Finally detecting the windows in a precision detection and merging the detecting windows. The target detection process is carried out in the following three steps.
Technical Paper

Evaluation of Global and Local Deformation Behaviors of Similar Laser Welded Joints using Digital Image Correlation

2014-04-01
2014-01-0832
Similar laser welded blanks with same material and same gauge have been extensive applied in automobile body for improving the material utilization and extending maximum coil size. It is known that, for TWBs with dissimilar material and thicknesses, the difference of material properties and/or thickness of the welded blanks, change of the material properties in the weld seam and heat-affected zones (HAZ) as well as location and orientation of the weld seam are reasons for reduced formability. However, the plastic deformation capacity of TWBs is reduced even when the material and thickness are the same. The aim of this paper is to evaluate the deformation behaviors of similar laser welded joints. Uniaxial tensile of five laser welded joints, with 90°,60°,45°,30°and 0°weld orientations, were tested by using optical measurement-DIC (Digital Image Correlation). Strain /strain ratio distribution and evolution of each joint was analyzed and compared with base material.
Technical Paper

Development of a Compact Compound Power-Split Hybrid Transmission Based on Altered Ravigneaux Gear Set

2014-04-01
2014-01-1793
Several types of power-split hybrid transmissions are outlined and the strengths and weaknesses of typical compound power-split prototype designs are summarized in this paper. Based on an modified Ravigneaux gear set, a novel compound power-split hybrid transmission with compact mechanical structure is presented, its dynamic and kinematic characteristics in equations and operating modes are described, and then equivalent lever diagrams are used to investigate the proposed compound power-split device. Control strategies in different operating modes are discussed with the simplified combined lever diagram, and a global optimization method is implemented to find the optimum operation point for the hybrid powertrain. To evaluate the fuel economy of a hybrid car equipped with this hybrid transmission, a forward powertrain simulation model is developed and real vehicle performance tests are conducted in the chassis dynamometer.
Technical Paper

Correlation of Objective and Subjective Evaluation in Automotive Brake Pedal Feel

2018-10-05
2018-01-1889
In order to establish the correlation between objective and subjective evaluation of brake pedal feel for passenger cars, road tests of brake pedal feel were carried out and an evaluation method was proposed. In the road tests, subjective scores and objective measurements were obtained under the conditions of uniform and emergency braking. The objective measurements include pedal preload, low deceleration pedal force and travel, moderate deceleration pedal force and travel, brake response time and brake linearity. Using the theory of analytic hierarchy process (AHP), the design process of the evaluation method was established. Key setups including the hierarchical structure model, the judgement matrix and the score calculation method of objective measurements were described in detail. Then, the correlation between subjective and objective scores was analyzed. It can be concluded that the evaluation method is effective and it can be applied to brake pedal feel assessment and adjustment.
Technical Paper

A New Narrowband Active Noise Control System in the Presence of Frequency Mismatch and its Application for Steady-State Blower Noise

2015-06-15
2015-01-2214
In order to reduce high-frequency harmonic noise produced by the blower in the auxiliary system of a fuel cell vehicle (FCV), a narrowband active noise control (ANC) method instead of conventional passive mufflers is adopted since the blower demands clean air condition and expects good acoustic performance. However, in ANC practical applications, the frequency difference between reference signal and actual primary signal, i.e., frequency mismatch (FM), can significantly degrade the high-frequency performance of narrowband ANC system. In this paper, a new narrowband ANC system is proposed to compensate for the performance degeneration due to the existence of FM and improve noise reduction at high frequencies. The proposed system consists of two parts: the Filtered Error Least Mean Square (FELMS) algorithm filtering the primary signals at wide frequency range other than those at the targeted frequencies, and the FM removal algorithm proposed by Yegui Xiao.
Technical Paper

Hybrid Brake System Control Strategy in Typical Transient Conditions

2014-04-01
2014-01-0267
The control in transient conditions when hydraulic brake and regenerative brake switch mutually is the key technical issue about electric vehicle hybrid brake system, which has a direct influence on the braking feel of driver and vehicle braking comfort. A coordination control system has been proposed, including brake force distribution correction module and motor force compensation module. Brake force distribution correction module has fixed the distribution results in hydraulic brake force intervention condition, hydraulic brake force evacuation condition and regenerative brake force low speed evacuation condition. Motor compensation module has compensated hydraulic system with motor system, which has fast and accurate response, thus the response of whole hybrid system has been improved.
X