Search Results

Software usability is a quality attribute defined as ?the extent to which a product can be used by specified users to achieve specified goals with effectiveness, efficiency and satisfaction in a specific context of use? (ISO 9241, 1998), usability is also referred to as ?quality in use? (ISO 14598, 1999). Presenter Anabell Beltran, Stoneridge Electronics North America

The paper describes the approach, addresses integration challenges and discusses capabilities of the Hybrid Powertrain-in-the-Loop (H-PIL) facility for the series/hydrostatic hydraulic hybrid system. We describe the simulation of the open-loop and closed-loop hydraulic hybrid systems in H-PIL and its use for concurrent engineering and development of advanced supervisory strategies. Presenter Fernando Tavares, Univ. of Michigan

The compressive behavior of lithium-iron phosphate battery cells is investigated by conducting in-plane constrained compression tests and out-of-plane compression tests of representative volume element (RVE) specimens. The results for cell RVE specimens under in-plane constrained compression tests without pre-strains and with pre-strains in the out-of-plane direction indicate that the load carrying capacity is characterized by the buckling of cell specimens. As the pre-strain increases, the nominal compressive stress-strain curve becomes higher. The nominal stress-strain curves in the out-of-plane direction were also obtained and used to determine the elastic moduli for the elastic buckling analyses of the cell components in the cell RVE specimens with different pre-strains. Based on the elastic buckling analyses for a beam with different lateral constraints due to different pre-strains in the out-of-plane direction, the number of half waves and the buckling stresses were obtained.

This paper describes the development of the fixed seat eyellipse in the October 2008 revision of SAE Recommended Practice J941. The eye locations of 23 men and women with a wide range of stature were recorded as they sat in each of three second-row bench seats in a laboratory mockup. Testing was conducted at 19-, 23-, and 27-degree seat back angles. Regression analysis demonstrated that passenger eye location was significantly affected by stature and by seat back angle. The regression results were used to develop an elliptical approximation of the distribution of adult passenger eye locations, applying a methodology previously used to develop the driver eyellipse in SAE J941-2002.

Electrification and hybridization show great potential for improving fuel economy and reducing emission in heavy-duty vehicles. However, high battery cost is unavoidable due to the requirement for large batteries capable of providing high electric power for propulsion. The battery size and cost can be reduced with advanced battery control strategies ensuring safe and robust operation covering infrequent extreme conditions. In this paper, the impact of such a battery control strategy on battery sizing and fuel economy is investigated under various military and heavy-duty driving cycles. The control strategy uses estimated Li-ion concentration information in the electrodes to prevent battery over-charging and over-discharging under aggressive driving conditions. Excessive battery operation is moderated by adjusting allowable battery power limits through the feedback of electrode-averaged Li-ion concentration estimated by an extended Kalman filter (EKF).

Seat comfort is driven in part by the fit between the sitter and seat. Traditional anthropometric data provide little information about the size and shape of the torso that can be used for backrest design. This study introduces a methodology for using three-dimensional computer models of the human torso based on a statistical analysis of body shapes for conducting automated fit assessments. Surface scan data from 296 men and 417 women in a seated posture were analyzed to create a body shape model that can be adjusted to a range of statures, body shape, and postures spanning those typical of vehicle occupants. Finite-element models of two auto seat surface were created, along with custom software that generates body models and postures them in the seat. A simple simulation technique was developed to rapidly assess the fit of the torso relative to the seat back.

Understanding the lightweighting potential of materials is important in making strategic decisions for material selection for a new vehicle program. Frequently benchmarking is done to support these decisions by selecting a reference vehicle which is believed to be mass efficient, then using the teardown mass data to set targets for the vehicle under design. In this work, rather then considering a single benchmark vehicle or a small set of vehicles, we looked at a large sample of vehicles over a range of sizes and segments (approximately 200 vehicles). Statistical methods were used to identify mass drivers for each subsystem. Mass drivers are the attributes of the vehicle and subsystem which determine subsystem mass. Understanding mass-drivers allows comparisons across vehicle size, segments, and materials. Next, we identified those vehicles which had subsystems which were much lighter than the average after adjusting for mass drivers. This set was defined as mass-efficient designs.

The fore-aft location of the steering wheel relative to the pedals is a critical determinant of driving posture and comfort. Current SAE practices lack quantitative guidance on steering wheel positioning. This paper presents a model of subjective preference for fore-aft steering wheel position across a range of seat heights. Sixty-eight men and women evaluated the steering wheel positions in a total of 9 package conditions differentiated by seat height and fore-aft steering wheel position. Numerical responses were given on a 7-point scale anchored with the words “Too Close”, “Just Right”, and “Too Far”. A statistical analysis of the results demonstrated that the preferred fore-aft steering wheel position was affected by seat height and driver stature. An ordinal logistic regression model was created that predicts the distribution of subjective responses to steering wheel location. The model can be used to calculate the preferred steering wheel position for individuals or populations.

Seat belt anchorage locations have a strong effect on occupant protection. Federal Motor Vehicle Safety Standard (FMVSS) 210 specifies requirements for the layout of the anchorages relative to the seating reference point and seat back angle established by the SAE J826 H-point manikin. Sled testing and computational simulation has established that belt anchorage locations have a strong effect on occupant kinematics, particularly for child occupants using the belt as their primary restraint. As part of a larger study of vehicle geometry, the locations of the anchorage points in the second-row, outboard seating positions of 83 passenger cars and light trucks with a median model year of 2005 were measured. The lower anchorage locations spanned the entire range of lap belt angles permissible under FMVSS 210 and the upper anchorages (D-ring locations) were distributed widely as well.

The number of control actuators available on spark-ignition engines is rapidly increasing to meet demand for improved fuel economy and reduced exhaust emissions. The added complexity greatly complicates control strategy development because there can be a wide range of potential actuator settings at each engine operating condition, and map-based actuator calibration becomes challenging as the number of control degrees of freedom expand significantly. Many engine actuators, such as variable valve actuation and flow control valves, directly influence in-cylinder combustion through changes in gas exchange, mixture preparation, and charge motion. The addition of these types of actuators makes it difficult to predict the influences of individual actuator positioning on in-cylinder combustion without substantial experimental complexity.

Rechargeable energy storage systems with Lithium-ion pouch cells are subject to various ambient temperature conditions and go through thousands of charge-discharge cycles during the life time of operation. The cells may change their thickness with internal heat generation, cycling and any other mechanisms. The stacked prismatic cells thus experience face pressure and this could impact the pack electrical performance. The pack consists of stiff end plates keeping the pack in tact using bolts, cooling fins to maintain cell temperature and foam padding in between cells. The pack level thermal requirements limit the amount of temperature increase during normal operating conditions. Similarly, the structural requirements state that the stresses and the deflection in the end plates should be minimal. Uncertainties in cell, foam mechanical and thermal properties might add variation to the pack performance.

This study evaluates powertrain technologies capable of reducing light duty vehicle fuel consumption for compliance with 2025 CAFE standards. A fully integrated GT-Power engine model with physics based sub-models was developed to capture any positive or negative synergies between the technologies. The two zone multi-cylinder engine model included typical thermodynamic subroutines, with predictive combustion, flame quench and knock models, along with map-based turbocharger models to capture key combustion and efficiency behaviors. The engine model was calibrated to data from a boosted GDI engine and exercised through one series of current and production viable technology configurations for 2025 regulations.

This study evaluates the fuel economy implication of powertrain technologies capable of reducing light duty vehicle fuel consumption for compliance with 2025 CAFE standards. In a companion paper, a fully integrated GT-Power engine model was used to evaluate the effectiveness of one plausible series of engine technologies, including valve train improvements such as dual cam phasing and discrete variable valve lift, and engine downsizing with turbocharging and cooled EGR. In this paper, those engine efficiency/performance results are used in a vehicle drive cycle simulation to estimate the impact of engine and transmission technology improvements on light duty vehicle fuel consumption/economy over the EPA’s FTP and HWY test schedules. The model test vehicle is a midsized sedan based on the MY2012 Ford Fusion.

Energy security and climate change challenges provide a strong impetus for investigating Electric Vehicle (EV) concepts. EVs link two major infrastructures, the transportation and the electric power grid. This provides a chance to bring other sources of energy into transportation, displace petroleum and, with the right mix of power generation sources, reduce CO₂ emissions. The main obstacles for introducing a large numbers of EVs are cost, battery weight, and vehicle range. Battery health is also a factor, both directly and indirectly, by introducing limits on depth of discharge. This paper considers a low-cost path for extending the range of a small urban EV by integrating a parallel hydraulic system for harvesting and reusing braking energy. The idea behind the concept is to avoid replacement of lead-acid or small Li-Ion batteries with a very expensive Li-Ion pack, and instead use a low-cost hydraulic system to achieve comparable range improvements.

An oil-lubricated wet clutch has a direct impact on the drivability and fuel economy of a vehicle equipped with an automatic transmission system. However, a reliable analysis of clutch behavior still remains a challenge. The purpose of this study is to advance the state-of the-art in CFD methodology for modeling transient clutch behavior. First, a new iterative scheme is developed, in combination with commercial CFD software, which is capable of simulating the squeeze film process in a wet clutch. The numerical results are then validated using analytical solutions of the Reynolds equation for simplified clutch geometry and various boundary conditions. It is found that the choice of boundary conditions has a strong influence on squeeze film simulation. The iterative scheme is further validated by comparison to clutch engagement experiments.

The paper describes the approach, addresses integration challenges and discusses capabilities of the Hybrid Powertrain-in-the-Loop (H-PIL) facility for the series/hydrostatic hydraulic hybrid system. We describe the simulation of the open-loop and closed-loop hydraulic hybrid systems in H-PIL and its use for concurrent engineering and development of advanced supervisory strategies. The configuration of the hydraulic-hybrid system and details of the hydraulic circuit developed for the H-PIL integration are presented. Next, software and hardware interfaces between the real components and virtual systems are developed, and special attention is given to linking component-level controllers and system-level supervisory control. The H-PIL setup allows imposing realistic dynamic loads on hydraulic pump/motors and accumulator based on vehicle driving schedule.

A supervisory controller strategy for a hybrid vehicle coordinates the operation of the two power sources onboard of a vehicle to maximize objectives like fuel economy. In the past, various control strategies have been developed using heuristics as well as optimal control theory. The Stochastic Dynamic Programming (SDP) has been previously applied to determine implementable optimal control policies for discrete time dynamic systems whose states evolve according to given transition probabilities. However, the approach is constrained by the curse of dimensionality, i.e. an exponential increase in computational effort with increase in system state space, faced by dynamic programming based algorithms. This paper proposes a novel approach capable of overcoming the curse of dimensionality and solving policy optimization for a system with very large design state space.

In this study, two sled series were conducted with a sled buck representing a compact vehicle. The first series of tests focused on the effects of crash pulse, impact angle, occupant size, and front seat location on rear seat occupant restraint with a generic rear-seat belt system without pre-tensioner or load limiter. The second series of tests focused on investigating the benefit of using advanced features for rear-seat occupant restraint in the most severe crash condition in the first sled series. The first series of tests include 16 test conditions with two impact angles (0° and 15°), two sled pulse (soft and severe), and four ATD sizes (HIII 6YO, HIII 5th female, HIII 95th male, and THOR-NT) with two ATDs in each test. The driver seat was located at the mid position, while the front passenger seat was positioned such that a constant distance between the ATD knee and the front seat is achieved.

New vehicle control algorithms are needed to meet future emissions and fuel economy mandates that are quite likely to require a measurement of ambient specific humidity (SH). Current practice is to obtain the SH by measurement of relative humidity (RH), temperature and barometric pressure with physical sensors, and then to estimate the SH using a fit equation. In this paper a novel approach is described: a system of neural networks trained to estimate the SH using data that already exists on the vehicle bus. The neural network system, which is referred to as a virtual SH sensor, incorporates information from the global navigation satellite system such as longitude, latitude, time and date, and from the vehicle climate control system such as temperature and barometric pressure, and outputs an estimate of SH. The conclusion of this preliminary study is that neural networks have the potential of being used as a virtual sensor for estimating ambient and intake manifold's SH.

As lightweight materials and advanced combustion engines are being used in both conventional and electrified vehicles with diverse fuels, it is necessary to evaluate the individual and combined impact of these technologies to reduce energy and greenhouse gas (GHG) emissions. This work uses life cycle assessment (LCA) to evaluate the total energy and GHG emissions for baseline and lightweight internal combustion vehicles (ICVs), hybrid electric vehicles (HEVs) and plug-in hybrid electric vehicles (PHEVs) when they are operated with baseline and advanced gasoline and ethanol engines. Lightweight vehicle models are evaluated with primary body-in-white (BIW) mass reductions using aluminum and advanced/high strength steel (A/HSS) and secondary mass reductions that include powertrain re-sizing. Advanced engine/fuel strategies are included in the vehicle models with fuel economy maps developed from single cylinder engine models.