Search Results

Due to the large negative impact of combustion gas emissions on air quality and the more stringent environmental legislation, research on internal combustion engines (ICE) are being developed to reduce emissions of pollutant gases to the atmosphere. One of the research fronts is the use of lean mixtures with the pre-chamber ignition system (PCIS). This system consists of a pre-chamber (PC) connected to the main chamber by one or more interconnecting holes. A spark plug initiates combustion of the mixture present in the pre-chamber, which is propagated as gas jet into the main chamber, igniting the lean mixture present therein. The gas jets have high thermal and kinetic energy, which promote faster combustion duration, making the system less prone to knock and with lower cyclic variability of the IMEP, enabling the lean limit extension. The pre-chamber system can be assisted with a supplementary liquid or gaseous fuel injection, enabling the charge stratification.

Atmospheric pollution is the major public health issue in many cities around the world. Internal combustion engines (ICE) and industries are common sources of pollutants that aggravate this situation. Aiming to overcome this problem, increasingly restrictive legislation on combustion pollutant emissions has been formulated and new technologies are being developed to ensure compliance with such restrictions. In this scenario, the lean mixtures appear as a possible alternative, but also bring some inconveniences such as combustion instabilities. Pre-chamber ignition systems (PCIS) enable a more stable combustion process due to high kinetic, thermal and chemical energy of the gases from the pre-chamber (PC), which pass through nozzles and begin the combustion process of the air-fuel mixture contained in the main combustion chamber (MC). However, some challenges still have to be overcome in the development of these systems, one of the main ones being hydrocarbon (HC) emissions.

The work focuses on studying ethanol spray behavior injected directly inside a spark ignited internal combustion engine in the compression stroke. An experimental procedure for measuring spray penetration and spray overall cone angle produced by a multi-hole direct injector was developed by means of computational codes written in Matlab environment for working with images of spray injections and to acquire calculated results in an automatic way. The shadowgraph technique with back continuous illumination associated with a high speed recording image process was used in a single cylinder optical research engine for acquiring images of Brazilian ethanol fuel injected at 120° before the top dead center of compression stroke. The process of spray injections occurred with engine speeds of 1000 rpm, 2000 rpm and 3000 rpm. The results showed that spray penetrations decrease and spray cone angle increase when the engine speed is raised.

Driven by the necessity to reduce costs and improve products quality the automotive industry replaced the design method known as "trial and error" by those grounded on mathematical and physical theory. In this context, a longitudinal performance test was made by BAJA SAE UFMG team, in order to acquire vehicular performance data that will be used to validate computer models. The methodology consists of sensors and data acquisition system research, validation, fixation and installation in the vehicle, test and process of acquired data. From these steps, correlated data were acquired from magnitudes such as angular velocity in transmission shafts, global longitudinal acceleration and velocity, travel of break and throttle pedals and pressure inside of master cylinder. These results developed the knowledge about vehicular dynamic allowing the improvement of futures prototypes.

The torch ignition system consists in the inflammation of the air/fuel mixture by means of gases jet flames that constitute ignition lines. Engines with this feature have a cavity or combustion pre-chamber, physically separate from the main chamber. In these systems happens a larger turbulence generation, due the movement of the gases inside the pre-chamber and through the interconnection orifices. The charge stratification, by means of an auxiliary inlet fuel system, also contributes for the fast and insurance inflammation of lean mixtures and the most varied combustible, including the difficult direct spark ignition fuels. This work presents the design elaboration of combustion pre-chamber from an analysis of the influence of the main constructive parameters in the combustion process.

In this work is proposed the installation of a turbocharger in a low dislocated volume engine, aiming to achieve a higher effective mean pressure and air fuel mixture density, for a better performance of the converted engine. This analysis is made through experimental tests in a break bench, following the Brazilian standard NBR ISO 1585. The results presented shows the basic behavior of the torque curves, power and gas emission, which reflects the changes in performance with both fuels for a aspirated and turbocharged engine, for all the engine rotation speeds. These results show the technical and economical viability of the conversion to Vehicular Natural Gas of a low cc engine, when adapted a commercial turbocharger kit.

The trends in the development of spark ignition engines leads to the adoption of lean mixtures in the combustion chamber. Torch ignition systems have potential to reduce simultaneously the NOx and CO emissions, while keeping the fuel conversion efficiency at a high level. This study aims to design and analyze a torch ignition system running with ethanol on lean homogeneous charge, adapted to an Otto cycle single-cylinder engine with optical visualization. The main objective is to achieve combustion stability under lean burn operation and to expand the flammability limit for increasing engine efficiency by means of redesigning the ignition system adapting a pre-chamber to the main combustion chamber. Experiments were conducted at constant speed (1000 rpm) using ethanol (E100) as fuel, for a wide range of injection, ignition and mixture formation parameters. Specific fuel consumption and combustion stability were evaluated at each excess air ratio.

The emission of nitric oxide (NOx) is the most difficult to limit among numerous harmful exhaust gas components. The NOX emission of internal combustion engines is mainly NO, but it will be oxidized into NO2 quickly after entering the air. NO is formed inside the combustion chamber in post-flame combustion by the oxidation of nitrogen from the air in conditions that are dependent on the chemical composition of the mixture, temperature and pressure. The correlation between NO emissions and temperature in the combustion chamber is a result of the endothermic nature of these reactions and can be described by extended Zeldovich Mechanism. The stratified torch ignition engine is able to run with lean mixture and low cyclic variability. Due to lean operation, the in-cylinder temperature of the STI engine is significantly lower than the conventional spark ignited one. This fact lead to a substantial reduction in NOx specific emission.

Global climate change and an increasing energy demand are driving the scientific community to further advance internal combustion engine technology. Invented by Sr. Henry Ricardo in 1918 the torch ignition system was able to significantly decrease engine’s fuel consumption and emission levels. Since the late 70s, soon after the Compound Vortex Controlled Combustion (CVCC) created by Honda, the torch ignition system R&D almost ceased due to the issues encountered by very complex and costly mechanic control systems that time. This work presents a stratified torch ignition prototype endowed with a sophisticated electronic control systems and components such as electro-injectors from direct injection systems placed on the pre-combustion chamber. The torch ignition prototype was tested and its performance are presented and compared with the baseline engine, which was used as a workhorse for the prototype engine construction.

This work aims to study the selection of a heat exchanger available in the market with the objective of implementing it in a vehicle. The vehicle used for the tests was a prototype, developed by Formula UFMG team. It was made an experimental and a theoretical study in order to calculate the power of the CB600F engine to compare with the experimental study of heat dissipation of the selected heat exchanger. This comparison was made to check whether the heat exchanger reaches the vehicle’s requirements, and it has shown good convergence. The engine technical features were used in the theoretical studies, and thus the power was calculated. The experimental data were obtained by assembling the car in a roller dynamometer with the necessary instrumentation for these tests being performed. In these tests, the critical operation conditions of the vehicle were simulated, once the engine operates at a temperature of 95°C.

The growing demand for more efficient and less polluting engines has lead the scientific community to further develop the road map engine technologies, including direct fuel injection. Direct injection research demands the investigation of spray formation and its characteristics. The present work performs the characterization of the macroscopic parameters of ethanol sprays (E100) produced with a fuel gauge pressure of 80 bar and gauge back pressures of 0, 5 and 10 bar. The sprays analysis was performed using high speed filming by means of Shadowgraph technique. Computational routines of matrix analysis were applied to measure the spray cone angles, penetration and penetration rate. The spray visualization demanded an experimental apparatus composed of a pressurized cylinder with nitrogen, a fuel tank as pressure vessel, an injection driver equipped with a peak and hold module controlled by a MoteC M84, a Phantom V7.3 high speed camera and LEDs for illumination.

Aiming the decrease of manufacturing costs, the automotive industry uses Computational Aided Engineering (CAE) and prototype testing for product development. In the field of simulation CAE could be performed using FEA (finite element analysis) or CFD (Computational Fluid Dynamic), the last one is the analysis of systems involving fluid flow, heat transfer and associated phenomena such as chemical reactions by means of computer-based simulation. One of the most important components of cooling system is a water pump which is evaluated through the fluid dynamic analysis. Therefore, this work aims to analyze the fluid flow inside an automotive water pump considering a three-dimensional steady-state using CFD, but also developing a methodology to evaluate it. The parameters of the analysis and the volumetric mesh were according to the simulated results approached the experimental results.

The automobile industry and its growing commitment to the environment have collaborated in the development of technologies to reduce emissions of gaseous pollutants, including hydrocarbons. Recent works are aimed at the development of the torch ignition in internal combustion engines of the Otto cycle. A prototype characterized by a torch ignition system with fixed geometry of pre-chamber per cylinder, with a volume of 3.66 cm3 and a single nozzle with a diameter of 6.00 mm, fed with homogeneous mixture originating from Combustion chamber. The ignition and injection system was controlled by a reprogrammable electronic management system. The main results were an increase of around 10% in thermal efficiency and reductions of up to 91% in carbon monoxide emissions, but there was a considerable increase in total hydrocarbons (THC) emissions.

A burning process in a combustion chamber of an internal combustion engine is very important to know the maximum temperature of the gases, the speed of combustion, and the ignition delay time of fuel and air mixture exact moment at which ignition will occur. The automobilist industry has invested considerable amounts of resources in numerical modeling and simulations in order to obtain relevant information about the processes in the combustion chamber and then extract the maximum engine performance control the emission of pollutants and formulate new fuels. This study aimed to general construction and instrumentation of a shock tube for measuring shock wave. As specific objective was determined reaction rate and ignition delay time of ethanol doped with different levels of additive enhancer cetane number. The results are compared with the delays measured for the ignition diesel and biodiesel.

Global trends in the development of spark ignition internal combustion engines lead to the adoption of solutions that reduce CO2 emissions and fuel consumption. Downsizing is a well-established path for this reduction, but it is necessary to use other technologies in order to achieve these ever more rigorous levels. A homogeneous torch ignition system is a viable alternative for reducing CO2 emissions with a combined reduction in specific fuel consumption and increased thermal efficiency. Thus a prototype adapted from an Otto engine with four cylinders is used for analysis. The performance and CO2 emission reference data were initially obtained with the baseline engine operating with a stoichiometric mixture. Then for the same conditions of BMEP, angular velocity and gradual lean of the mixture from the stoichiometry, the results of the adapted system are obtained.

It developed a design and construction methodology of a stratified charge torch ignition system for an Otto engine aiming fuel consumption and pollutant emission reduction. The torch ignition system is made of a combustion pre-chamber equipped with a direct fuel injector, an air injector and a spark plug. Fuel is directly injected in the pre-chamber aiming the formation of a lightly rich air fuel mixture. The combustion process starts in the pre-chamber and as the pressure rises, combustion jet flames are produced through interconnection nozzles into the main chamber. The high thermal energy of the jet flames reduces the combustion time, increases the combustion efficiency and allows the engine to efficiently burn lean air fuel mixture of several kinds of fuel in the main chamber, even those that are difficult to ignite. After the combustion takes place in the pre-chamber, air is also injected to help the exhaust process of the combustion products of the previous cycle.

To attend the new tendencies of the automotive market, new technologies must be used throughout the engine conception. One way of improving the project is to use computational numerical simulation, predicting engine behavior in a wide range of situations. This paper presents a methodology to estimate the engine characteristic parameters necessary to numerical simulation. Morse test was used to determine friction power, mean effective pressure friction and friction torque, considering the engine behavior during cylinder ignition cut-off. In this test all the results were compatible with manufacturer data, which validates the methodology. To define the moment of inertia, it's also proposed a fuel cut methodology, associated with the Morse test, because the torque values measured by dynamometer after the fuel cut did not correspond to the real value. Thus, plausible values of engine moment of inertia, very close to values obtained by software, were obtained.

Future engine control systems need suitable and accurate models for combustion. For this purpose, this paper presents a practical application of nonlinear autoregressive moving average polynomial models with exogenous inputs (NARMAX) technique to model pressure dynamics inside the cylinder of a direct injection compression ignition engine. Two models have been investigated taking two different sets of input variables. The first model only includes basic injection settings available from the electronic control unit. The second model uses the instantaneous crankshaft revolution speed as a main model input. Model parameter identification and validation are performed with experimental data obtained from a test engine equipped with a piezoelectric pressure sensor and with data computed from a thermodynamic-based engine cycle simulation code.

Environmental policies and fuel costs have driven the development of new technologies for internal combustion engines. In this sense, the use of mixtures with small portions of fuel allows lower fuel consumption and pollutants emissions, emerging as a promising strategy. Despite the advantages, lean burn requires a larger energy source to provide satisfactory flame propagation speed and consequently a stable combustion. The use of pre-chamber ignition systems (PCIS) has been used in SI engines to assist the start of combustion of lean mixtures, in which a supplementary fuel system can stratify the amount of either liquid or gaseous fuels supplied to the pre-chamber. In this context, this paper aims to evaluate combustion characteristics of a commercial engine with the use of stratified PCIS operating with impoverished mixtures of ethanol-air in main-chamber and hydrogen assistance in pre-chamber.

Extensive studies of pre-chamber ignition systems in internal combustion engines have proven its effectiveness in reduction of fuel consumption and improvement in several combustion parameters. Considering the different types of pre-chamber configurations, this paper aims to compare the combustion in a SI engine with both homogeneous and stratified pre-chamber ignition systems. To achieve this objective a system with the ability to control the hydrogen injection in the pre-chamber was built. This system was installed in a multi-cylinder Ford Sigma 1.6L engine and tested in a dynamometric room. Tests consisted in imposing a constant rotation and IMEP to test three conditions: standard spark ignition, pre-chamber ignition system without fuel injection (homogenous) and with hydrogen injection (stratified). It was possible to identify that with the use of pre-chamber ignition system there is a reduction in specific fuel consumption and in the combustion duration.