Search Results

This method of gaging alignment of nut slots allows equal variations for location of the cotter pin hole in the bolt and location of slots in the nut. To inspect the nut, the slotted gage is inserted through the nut hole from the bearing surface of the nut. Alignment of slots is considered satisfactory if the gage pin can be slipped into the gage and nut slots without interference.

Round head bolts are made in two body styles: (a) A full size body, with a maximum diameter somewhat greater than the nominal diameter (not an SAE Standard except for ribbed neck bolts, Table 3); and (b) an undersize body, with a minimum diameter approximating the pitch diameter of the thread and a maximum diameter never exceeding nominal (SAE standard for all types except ribbed neck bolts). The body diameter of either style may be exceeded by a reasonable swelling or fin under the head, or under corners of the square necks, to the extent that serviceability is not affected.

This paper compares two different rule-based power management (PM) strategies, in terms of their resultant fuel consumptions, through a simulation study as applied to a hybrid hydraulic multi-actuator displacement controlled (DC) system. Presenter Rohit Hippalgaonkar

Optical fiber has begun replacing copper in avionic networks. So far, however, it has been mainly restricted to non-critical applications (video transmission to the flight deck, IFE?). In order to take advantage of the high-bandwidth, low weight, no EMI properties of optical fibers in all data transmission networks, it will be necessary to improve the testing. One part of the puzzle, which is still missing, is the self-test button: the possibility to check the network and detect potential failures before they occur. The typical testing tool of a technician involved in optical fiber cables is the ?light source ? optical power meter? pair. With this tool, one can measure the insertion loss of the fiber link. A second important parameter, the return loss at each optical connector, is not analysed. In addition, this is only a global measurement, which does not allow the detection of possible weak points.

This presentation shows the SCADE System product line for systems modeling and generation based on the SysML standard and the Eclipse Papyrus open source technology. SCADE System has been developed in the framework of Listerel, a joint laboratory of Esterel Technologies, provider of the SCADE�, and CEA LIST, project leader of the Eclipse component, Papyrus. From an architecture point of view, the Esterel SCADE tools are built on top of the SCADE platform which includes both SCADE Suite�, a model-based development environment dedicated to critical software, and SCADE System enabling model-based system engineering. SCADE System includes Papyrus, an open source component (under EPL license), integrated in the modeling platform of Eclipse. Using this integrated modeling platform, both system and software teams share the same environment for system development. Furthermore, other model-based tools can be added to the environment, due to the use of Eclipse.

In recent years, all major microprocessor manufacturers are transitioning towards the deploymenet of multiple processing cores on every chip. These multi-core architectures represent the industry consensus regarding the most effective utilization of available silicon resources to satisfy growing demands for processing and memory capacities. Porting off-the-shelf software capabilities to multi-core architectures often requires significant changes to data structures and algorithms. When developing new software capabilities specifically for deployment on SMP architectures, software engineers are required to address specific multi-core programming issues, and in the ideal, must do so in ways that are generic to many different multi-core target platforms. This talk provides an overview of the special considerations that must be addressed by software engineers targeting multi-core platforms and describes how the Java language facilitates solutions to these special challenges.

Probabilistic methods are used in calculating composite part design factors for, and are intended to conservatively compensate for worst case impact to composite parts used on space and aerospace vehicles. The current method to investigate impact damage of composite parts is visual based upon observation of an indentation. A more reliable and accurate determinant of impact damage is to measure impact energy. RF impact sensors can be used to gather data to establish an impact damage benchmark for deterministic design criteria that will reduce material applied to composite parts to compensate for uncertainties resulting from observed impact damage. Once the benchmark has been established, RF impact sensors will be applied to composite parts throughout their life-cycle to alert and identify the location of impact damage that exceeds the maximum established benchmark for impact.

Not available.

Not available.

This document standardizes the design of connector blocks used for joining SAE J518-1/ISO 6162-1 (Code 61) flange heads with other SAE J518-1/ISO 6162-1 (Code 61) flange heads with straight, elbow, and tee geometries. The blocks specified in this document are designed to provide for very compact installations. As a result, the tap depths specified in this document do not conform to those specified in SAE J518-1/ISO 6162-1 to allow for a minimal bend radius in the elbow and tee configurations. This document specifies both inch and metric configurations

Standardize plastic fitting hose terminations and drop distances for SAE J2044 fittings

The development of future more-and full-electric aircraft concepts has significantly impacted aircraft electric power system (EPS) design. Finalizing the EPS architectures involves extensive modeling and simulation activities to ensure the required characteristics of the entire EPS prior to the physical implementation. Hence, the development of accurate, effective and computational time-saving simulation models is of great importance. Correspondingly, there is a need to establish an EPS-specific modeling and simulations common framework to ensure effective and accurate solutions to the problems addressed. The document continues a series of AE-7M documents specific for aircraft electrical systems aiming to establish such a framework (the series has started with AIR 6326 "Aircraft Electrical Power Systems. Modeling and Simulation. Definitions" issued in August, 2015).

This document addresses many of the issues and challenges related to obtaining high quality measurements at the designated Aerodynamic Interface Plane (AIP) necessary to characterize the flow field. The intent is to consolidate information needed to understand the requirements, and techniques for obtaining quality measurements, and provide lessons learned from previous test programs. This document applies to Ground (wind tunnel and engine test) and Flight testing for inlet recovery and distortion for air vehicles.

This document provides an application guide for electric motors that drive aerospace hydraulic pumps. It provides details of the characteristics of electric motors powered by DC, Fixed Frequency AC, and Variable Frequency AC electrical systems. The applications include both military and commercial aircraft.

This document outlines the current state of the art in the understanding of gas in solution in shock absorber oils in unseperated shock absorbers. A literature review, overview of Henry's law, Henry's law coefficients for known gas and oil couples, in-service operational problems, lessons learned, and potential future work will be discussed in the document.

This document outlines historical systems which have used the landing gear as a sensor or installation point for full aircraft weight and balance systems. A number of systems have been developed, installed, certified, and placed in service but few systems remain in regular use. The document will capture the history of these systems, reasons (where known) for their withdrawal from service, and lessons learned.

This document will outline existing best practices in the instrumentation of landing gears for in-service operation (including flight test, operational loads monitoring, etc.).