Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

Logistics Product Data Reports Handbook

2015-10-21
WIP
TAHB0007_1A
This document describes a set of standardized reports that can be generated using the logistics product data elements contained in GEIA-STD-0007-B. Each report is defined by selection options, processing, format, report sequence, and data sources. The selection options paragraph identifies recommended mandatory and optional selections that can be made by the user to tailor the report content. The processing paragraph identifies qualifying criteria for report data, report calculations, and specific instructions regarding how the data should be presented on the report. Each report has a sample report showing its format. Report sequences specify the sort criteria for a given report, and each Part/Section within a report. There is an attached listing of data sources for the elements that are on a report. The listing provides the report header for each element; and its GEIA-STD-0007-B data element/attribute along with the appropriate entity.
Standard

Connections for On-Board Road Vehicle Electrical Wiring Harnesses - Part 2: Tests and General Performance Requirements

2018-10-22
WIP
J2223/2
Procedures included within this specification are intended to cover performance testing at all phases of development, production, and field analysis of electrical terminals, connectors, and components that constitute the electrical connection systems in low voltage (0 - 20 VDC) road vehicle applications. These procedures are only applicable to terminals used for In-Line, Header, and Device Connector systems with and without Shorting Bars. They are not applicable to Edge Board connector systems, greater than 20 VAC or DC, or to eyelet type terminals.
Standard

Daytime Running Light

2018-01-30
WIP
J2087
This SAE Standard provides test procedures, requirements, and guidelines for a daytime running light (DRL) function.
Standard

Dynamic Cleat Test with Perpendicular and Inclined Cleats

2018-04-16
WIP
J2730
This SAE Recommended Practice describes a test method for measuring the forces and moments generated at a high frequency response spindle when a rolling tire impacts a cleat. The cleat is configured either with its crest perpendicular, 90°, to the path of the tire or optionally with its crest inclined at an angle to the path of the tire. The carriage to which the spindle is attached is rigidly constrained in position during each test condition so as to provide a good approximation to fixed loaded radius operation. The method discussed in this document provides impact force and moment time histories essentially free from variations due to tire non-uniformities. The method applies to any size tire so long as the equipment is properly scaled to conduct the measurements for the intended test tire. The data are suitable for use in determining parameters for road load models and for comparative evaluations of the measured properties in research and development.
Standard

Steel Self-Drilling Tapping Screws

2014-09-09
WIP
J78
This SAE Standard covers the dimensional and general specifications, including performance requirements, for carbon steel self-drilling tapping screws suitable for use in general applications. It is the objective of this document to insure that carbon steel self-drilling tapping screws, by meeting the mechanical and performance requirements specified, shall drill a hole and form or cut mating threads in materials into which they are driven without deforming their own thread and without breaking during assembly. Appendix A is included to provide a recommended technique for measuring the case depth on the screws.
Standard

Inertia Dynamometer Rotor Crack Test Procedure for Air Disc Brakes

2018-04-27
WIP
J3080

This Recommended Practice applies to commercial vehicles equipped with air disc brakes and above 4536 kg of Gross Vehicle Weight Rating. Other assessments on the friction material or rotor related to wear, durability, correlation to product life, noise, judder, compliance to specific regulations, etc., are not part of this RP (Recommended practice).

Training / Education

Introduction to Finite Element Analysis

Anytime
Finite Element Analysis (FEA) is a computer-aided engineering (CAE) tool used to analyze how a design reacts under real-world conditions. Useful in structural, vibration, and thermal analysis, FEA has been widely implemented by automotive companies and is used by design engineers as a tool during the product development process. Design engineers analyze their own designs while they are still in the form of easily modifiable CAD models to allow for quick turnaround times and to ensure prompt implementation of analysis results in the design process.
Standard

Measurement of Passenger Compartment Refrigerant Concentrations Under System Refrigerant Leakage Conditions

2014-01-09
WIP
J2772
This Standard is restricted to refrigeration circuits that provide air-conditioning for the passenger compartments of passenger and commercial vehicles. This Standard includes analytical and physical test procedures to evaluate concentration inside the passenger compartment. In the early phases of vehicle evaluation, usage of the analytical approach may be sufficient without performing physical tests. The physical test procedure involves releasing refrigerant from an external source to a location adjacent to the evaporator core (inside the HVAC-Module). An apparatus is used to provide a repeatable, calibrated leak rate. If the system has multiple evaporators, leakage could be simulated at any of the evaporator locations. This standard gives detail information on the techniques for measuring R-744 [CO2] and R-1234yf [HFO-1234yf], but the general techniques described here can be used for other refrigerants as well.
Standard

Motorcycle Terminology

2016-10-26
WIP
J3133
The motorcycle terminology presented herein addresses two-wheel single track vehicles, as well as three wheel variants. . Although two-wheeled, single track scooters and mopeds are similar to traditional motorcycles, they have many characteristics which differentiate them from motorcycles, and while some terms will apply, this Terminology addresses motorcycles specifically, unless otherwise noted.
Standard

Reflex Reflectors for Use on Vehicles 2032 mm or More in Overall Width

2018-05-02
WIP
J2041
This SAE Standard provides test procedures, requirements, and guidelines for reflex reflectors used on vehicles 2032 mm or more in overall width. Reflex reflectors conforming to these requirements may also be used on vehicles less than 2032 mm in overall width.
Standard

Driver Vehicle Interface (DVI) Message Priority and Presentation

2018-11-05
WIP
J3189
This SAE Recommended Practice applies to both Original Equipment Manufacturer (OEM) and aftermarket message-generating systems for light and heavy vehicles. The recommended practice covers both message prioritization and presentation (including simultaneous display of messages) for visual and auditory modalities. In addition, this recommended practice will consider temporal aspects of external events (e.g. merging into heavy traffic, time-to-collision) and their impact on temporal presentation and format (including multi-modal) of messages.
Standard

Test Procedures for Evaluating Bolt-Load Retention of Magnesium Alloy

2018-11-02
WIP
USCAR35-1
1.1 A bolt-load retention (BLR) test is a practical test to determine the bolt load of a fastener joint with time and at given temperatures. There are three types of BLR tests described in this standard, namely general-purpose test, design-purpose test, and screening material test. A general-purpose BLR test may be used for screening materials, while a design-purpose BLR test is usually used to verify the BLR behavior of a specific joint. The screening material test is an example of the general-purpose test for typical automotive applications. 1.2 The test procedures provides guidance in the following areas: (a) BLR sample and test fixture, (b) test fastener, washer and nut, (c) bolt-load measurement and data acquisition, (d) heating device, (e) initial loading, (f) baseline test, and (g) instrumentation of strain gages and calibration (see Appendix B).
Standard

Air Dryer Test Procedure

2017-05-02
WIP
J2384
This SAE Recommended Practice establishes uniform Test Procedures for desiccant Air Dryers used in vehicles with compressed air systems per SAE J2383. Continuous flow desiccant Air Dryers are excluded from the scope of this document.
Standard

SAE Manual on Blast Cleaning

2011-03-17
WIP
J792
This reportl on blast cleaning is a companion to the SAE Manual on Shot Peening. It is intended to help engineers, management, and shop personnel to increase their knowledge of the process. The information contained herein has been submitted and edited by a group that has had extensive and varied experience with blast cleaning and whose recommendations merit consideration.
Standard

Brake Master Cylinder Plastic Reservoir Assembly for Road Vehicles

2018-10-28
WIP
J2053
This SAE Recommended Practice specifies the performance test procedures and requirements of a plastic reservoir assembly suitable for use on a hydraulic brake master cylinder (reference SAE J1153). Intended usage is for on-road vehicles using brake fluid conforming to fMVSS-116 (DOT 3), and SAE J1703 specifications. This document includes the cap.cover and diaphragm as integral parts of the reservoir assembly. The fluid level sensor (FLS) is also included as an integral part of the assembly. However, additional FLS standards and/or requirements are applicable and necessary which are not covered in this document. This document is intended to provide a recommended practice and minimum performance requirements of current established designs on those reservoir assemblies generally used by individual manufacturers which have demonstrated satisfactory field performance. This document is applicable to new reservoir assemblies for commercial or aftermarket production.
Standard

Crane Boom Hoist Disengaging Device

2017-08-15
WIP
J999
This SAE Standard applies to cranes which are equipped to adjust the boom angle by hoisting and lowering means through rope reeving. The purpose of this standard is to define the function and to stipulate the requirements of an automatic device to prevent raising a variable angle boom above its highest specified angle.
Standard

Ignition System Measurements Procedure

2014-10-23
WIP
J973
This SAE Recommended Practice is intended to provide any technical person or group interested in ignition system design and/or evaluation with the specific equipment, conditions, and methods which will produce test results definitive and reproducible for his own work and yet sufficiently standardized to be acceptable to other groups working on battery ignition systems for automotive engines.
X