Refine Your Search

Topic

Author

Affiliation

Search Results

Video

Development of a 3rd Generation SCR NH3-Direct Dosing System for Highly Efficient DeNOx

2012-06-18
In this project funded by the Bayerische Forschungsstiftung two fundamental investigations had been carried out: first a new N-rich liquid ammonia precursor solution based on guanidine salts had been completely characterized and secondly a new type of side-flow reactor for the controlled catalytic decomposition of aqueous NH3 precursor to ammonia gas has been designed, applied and tested in a 3 liter passenger car diesel engine. Guanidine salts came into the focus due to the fact of a high nitrogen-content derivate of urea (figure 1). Specially guanidinium formate has shown extraordinary solubility in water (more than 6 kg per 1 liter water at room temperature) and therefore a possible high ammonia potential per liter solution compared to the classical 32.5% aqueous urea solution (AUS32) standardized in ISO 22241 and known as DEF (diesel emission fluid), ARLA32 or AdBlue®. Additionally a guanidine based formulation could be realized with high freezing stability down to almost ?30 °C (?
Video

Impact of Biodiesel on Particle Emissions and DPF Regeneration Management in a Euro5 Automotive Diesel Engine

2012-06-18
Biofuel usage is increasingly expanding thanks to its significant contribution to a well-to-wheel (WTW) reduction of greenhouse gas (GHG) emissions. In addition, stringent emission standards make mandatory the use of Diesel Particulate Filter (DPF) for the particulate emissions control. The different physical properties and chemical composition of biofuels impact the overall engine behaviour. In particular, the PM emissions and the related DPF regeneration strategy are clearly affected by biofuel usage due mainly to its higher oxygen content and lower low heating value (LHV). More specifically, the PM emissions and the related DPF regeneration strategy are clearly affected by biofuel usage due mainly to its higher oxygen content and lower low heating value, respectively. The particle emissions, in fact, are lower mainly because of the higher oxygen content. Subsequently less frequent regenerations are required.
Standard

Sampling and Measurement of Bleed Air Supplies from Engines or APUs

2016-02-29
WIP
AIR6418
The scope of this document will consider a broader range of contaminants than ARP4418. In addition, it may provide guidance for measuring on wing, as well as in test cells, Finally, it may also discuss transient measurements, as well as steady state measurements.
Standard

Automatic Transmission Intake Filter Test Procedure

2018-08-28
WIP
J2312
This test procedure is intended to apply to hydraulic pump suction filters and strainers used in automotive automatic transmissions that include hydraulic power pumps. The various paragraphs of Section 5, “Test Procedures,” include a variety of tests and alternative tests that are not applicable to all filters and applications, so the engineer must specify which tests are to be performed for a particular application. These test procedures are intended to evaluate filter functional performance characteristics only, durability is not evaluated under this standard. Filter design requirements must be specified by the engineer on the filter assembly drawing, an applicable engineering specification, or summarized on an application data sheet similar to that found in this recommended practice. See Figure 6, “Filter Assembly Application and Data Sheet.” Pressure circuit filters, both barrier and system contamination control types, are not covered under this standard.
Standard

Measuring Aircraft Gas Turbine Engine Fine Fuel Filter Element Performance

2019-09-11
WIP
ARP1827D
This SAE Aerospace Recommended Practice (ARP) delineates two complementary filter element performance ratings: (1) dirt capacity, and (2) filtration efficiency, and corresponding test procedures. It is intended for non-cleanable (disposable), fine fuel filter elements used in aviation gas turbine engine fuel systems.
Technical Paper

Effects of Low Temperature Premixed Combustion (LTPC) on Emissions of a Modern Diesel Engine for Passenger Cars

2010-04-12
2010-01-0333
In this paper, a Low Temperature Premixed Combustion (LTPC) was investigated employing a four cylinder D.I. common rail Diesel engine, used for passenger cars on the European market. Experiments were carried out setting the engine speed at 2500 rpm with a fuel amount of 26 mg/str to realize an operating condition close to the point of NEDC at 0.8 MPa of BMEP. The experimental approach was the management of the start of injection, injection pressure and EGR rates as a method to control NOx and soot production. The investigation was first carried out testing engine performances and emissions as set from the commercial engine map. Afterward, engine tests were carried out exploring performances, gaseous and smoke emissions at late start of combustion [10 to 17.5 cad ATDC], injection pressures from 80 to 120 MPa and EGR rates up to 50%.
Technical Paper

Fuel Injection Effect on In-cylinder Formation and Exhaust Emission of Particulate from a 4-Stroke Engine for 2-Wheel Vehicles

2010-04-12
2010-01-0354
The small engine for two-wheel vehicles has generally high possibility to be optimized at low speeds and high loads. In these conditions fuel consumption and pollutants emission should be reduced maintaining the performance levels. This optimization can be realized only improving the basic knowledge of the thermo-fluid dynamic phenomena occurring during the combustion process. It is known that, during the fuel injection phase in PFI SI engines, thin films of liquid fuel can form on the valves surface and on the cylinder walls. Successively the fuel films interact with the intake manifold and the combustion chamber gas flow. During the normal combustion process, it is possible to achieve gas temperature and mixture strength conditions that lead to fuel film ignition. This phenomenon can create diffusion-controlled flames that can persist well after the normal combustion event. These flames induce the emission of soot and unburned hydrocarbons.
Technical Paper

Optimization of Control Parameters for a Heavy-Duty CNG Engine via Co-Simulation Analysis

2011-04-12
2011-01-0704
Internal combustion engines for vehicle propulsion are more and more sophisticated due to increasingly restrictive environmental regulations. In case of heavy-duty engines, Compressed Natural Gas (CNG) fueling coupled with Three-Way Catalyst (TWC) and Exhaust Gas Recirculation (EGR) can help in meeting the imposed emission limits and preventing from thermal stress of engine components. To cope with the new issues associated with the more complex hardware and to improve powertrain performance and reliability and after-treatment efficiency, the engine control strategies must be reformulated. The paper focuses on the steady-state optimization of control parameters for a heavy-duty engine fueled by CNG and equipped with turbocharger and EGR. The optimization analysis is carried out to design EGR, spark timing and wastegate control, aimed at increasing fuel economy while reducing in-cylinder temperature to prevent from thermal stress of engine components.
Technical Paper

Use of Renewable Oxygenated Fuels in Order to Reduce Particle Emissions from a GDI High Performance Engine

2011-04-12
2011-01-0628
The use of oxygenated and renewable fuels is nowadays a widespread means to reduce regulated pollutant emissions produced by internal combustion engines, as well as to reduce the greenhouse impact of transportation. Besides PM, NOx and HC emissions, also the size distribution of particles emitted at the engine exhaust represent meaningful information, considering its adverse effects on the environment and human health. In this work, the results of a comprehensive investigation on the combustion characteristics and the exhaust emissions of a GDI high performance engine, fuelled with pure bio-ethanol and European gasoline, are shown. The engine is a 4-cylinder, 4-stroke, 1750 cm₃ displacement, and turbocharged. The engine was operated at different speed/load conditions and two fuel injection strategies were investigated: homogeneous charge mode and stratified charge mode.
Technical Paper

Evaluation of Splash Models with High-Pressure Diesel Spray

2006-04-03
2006-01-1117
Spray impingement on walls is an important physical process in modern DI Diesel engines as it greatly influences mixture formation, combustion process and exhaust emissions. The mixture preparation is, in fact, a crucial aspect for the correct operation of the engine as it significantly affects the combustion process. In this paper three models, among the available in literature, have been selected and implemented in the KIVA-3V code. Namely, the models by O'Rourke and Amsden (OA model) [1, 2], by Bai and Gosman (BG model) [3] and by Lee et al. (LR model) [4, 5] are compared in terms of performance and capability of representing the splash phenomenon. The model capabilities are firstly tested comparing the numerical results with four sets of experimental literature data, characterized by low injection pressures. The high injection pressures of modern Diesel engines result in droplets velocities emerging from the nozzle greater than 300 m/s.
Technical Paper

Multi-Wavelength Spectroscopic Investigations of the Post-Injection Strategy Effect on the Fuel Vapor within the Exhaust Line of a Light Duty Diesel Engine Fuelled with B5 and B30

2013-10-14
2013-01-2519
Optical diagnostic was applied to undiluted engine exhaust to supply a low cost and real time evaluation of the oil dilution tendency of selected fuels. Specifically, UV-visible-near IR extinction spectroscopy was applied in the exhaust line of a Euro 5 turbocharged, water cooled, DI diesel engine, equipped with a common rail injection system. The engine was fuelled with commercial B5 fuel and a B30 v/v blend of RME and ultra low sulfur diesel. The proposed experimental methodology allowed to identify the contribution to the multi-wavelength extinction of soot, fuel vapor, hydrocarbons and nitrogen oxide. Further, the evolution of each species for different post-injection interval settings was followed. On-line optical results were correlated with off-line liquid fuel absorption values. Moreover, spectroscopic measurements were linked to in-cylinder pressure related data and with HC and smoke exhaust emissions.
Technical Paper

Knock Detection in a Turbocharged S.I. Engine Based on ARMA Technique and Chemical Kinetics

2013-10-14
2013-01-2510
During the last years, a number of techniques aimed at the experimental identification of the knocking onset in Spark-Ignition (SI) Internal Combustion Engines have been proposed. Besides the traditional procedures based on the processing of in-cylinder pressure data in the frequency domain, in the present paper two innovative methods are developed and compared. The first one is based on the use of statistical analysis by applying an Auto Regressive Moving Average (ARMA) technique, coupled to a prediction algorithm. It is shown that such parametric model, applied to the instantaneous in-cylinder pressure measurements, is highly sensitive to knock occurrence and is able to identify soft or heavy knock presence in different engine operating conditions. An alternative, more expensive procedure is developed and compared to the previous one.
Technical Paper

Experimental Investigation of a Methane-Gasoline Dual-Fuel Combustion in a Small Displacement Optical Engine

2013-09-08
2013-24-0046
In this paper the methane-gasoline dual fuel combustion was investigated. Gasoline was injected in the intake manifold (PFI fuel), while methane was injected in the combustion chamber (DI fuel), in order to reproduce a stratified combustion. The combustion process and the related engine performance and pollutant emissions were analyzed. The measurements were carried out in an optically accessible small single-cylinder four-stroke engine. It was equipped with the cylinder head of a commercial 250 cc engine representative of the most popular two-wheel vehicles in Europe. Optical measurements were performed to analyze the combustion process with high spatial and temporal resolution. In particular, optical techniques based on 2D-digital imaging were used to follow the flame front propagation and the soot and temperature concentration in the combustion chamber.
Technical Paper

Effect of Port Injected Ethanol on Combustion Characteristics in a Dual-Fuel Light Duty Diesel Engine

2013-04-08
2013-01-1692
Nowadays, alcoholic fuels gain increased interest as alternative transportation biofuel even in compression ignition engines due to the fact that they contain oxygen and can be produced in a sustainable way. Furthermore, due to their lower CN (Cetane Number) they suit better for premixed combustion applications. Experimental research was conducted on a single cylinder engine provided with modern engine architecture modified for DF (Dual-Fuel) purposes. The authors have investigated the use of ethanol in a DF engine in order to exploit its well-known advantages in premixed combustion mode. The DF approach appears to be a promising solution because it permits flexible control of the premixed fuel fraction regardless from the operating conditions. This improves the exploitation of the ethanol potential according the engine working conditions.
Technical Paper

Characterization of PCCI Combustion in a Single Cylinder CI Engine Fuelled with RME and Bio-Ethanol

2013-04-08
2013-01-1672
This paper reports experiments on a single-cylinder direct-injection compression ignition engine operating in premixed charge compression ignition (PCCI) combustion mode. The engine was fuelled with pure rapeseed methyl ester (RME) and bio-ethanol. RME was injected in the combustion chamber by common rail (CR) injection system at 800 bar and bio-ethanol in the intake manifold by commercial port fuel injection system at 3.5 bar. The effects of different percentage of bio-ethanol were studied by means of both the in-cylinder heat release analysis and the high-speed UV-visible chemiluminescence visualization. The pollutant formation and exhaust emissions of the engine operating in dual fuel mode were evaluated. The increase of the bio-ethanol content improved the brake thermal efficiency slightly even if the brake fuel consumption increased. However, the choice to inject two biofuels decreases both the smoke opacity and NOx concentration.
Technical Paper

Optical Investigation of Injection and Combustion Phases of a Fouled Piezoelectric Injector in a Transparent CR Diesel Engine

2013-04-08
2013-01-1591
This study was conducted to determine the effects of the fouling process on the piezoelectric injectors in a transparent common-rail diesel engine. Piezoelectric injectors are characterized by a ceramic actuator that can dilate or retract when it receives a pulse of current. The piezo element controls a valve, which creates an imbalance in the pressure that is exerted at each end of the needle, causing the needle rising or closing. Two same model injectors were tested; one was new and the other one was fouled on a vehicle. The aim of the experimental investigation was to evaluate the performance of a new and a fouled piezoelectric injector in terms of injection and flame evolution. It was evaluated how the nozzle carbon deposits affect the injection quantity and combustion. The experimental apparatus was a single-cylinder research engine equipped with a Euro 5 multi-cylinder head. A second-generation common rail injection system and 6-hole piezoelectric injectors were used too.
X