Search Results

Fuel efficiency and torque performance are two major challenges for highly downsized turbocharged engines. However, the inherent characteristics of the turbocharged SI engine such as negative PMEP, knock sensitivity and poor transient performance significantly limit its maximum potential. Conventional ways of improving the problems above normally concentrate solely on the engine side or turbocharger side leaving the exhaust manifold in between ignored. This paper investigates this neglected area by highlighting a novel means of gas exchange process. Divided Exhaust Period (DEP) is an alternative way of accomplishing the gas exchange process in turbocharged engines. The DEP concept engine features two exhaust valves but with separated function. The blow-down valve acts like a traditional turbocharged exhaust valve to evacuate the first portion of the exhaust gas to the turbine.

Noise emitted from the pump can be a major influence on the overall noise created by a power steering system. Dynamic simulation can aid the designer by showing the effect of the pump geometry and oil properties on noise before the prototype has been built. This paper discusses a simulation of suction port flow ripple in a power steering vane pump, which is validated against experimental data. Results show that the mean pressure in the delivery line affects the amplitude of suction port flow ripple. Internal leakage in the pump was found to have little effect on suction port flow ripple. The level of high-frequency flow ripple from the suction port was found to be comparable with or greater than that from the delivery port. The simulation is used to recommend the addition of relief grooves to reduce the high-frequency flow ripple.

Electric coolant pumps for IC engines are under development by a number of suppliers. They offer packaging and flexibility benefits to vehicle manufacturers. Their full potential will not be realised, however, unless an integrated approach is taken to the entire cooling system. The paper describes such a system comprising an advanced electric pump with the necessary flow controls and a supervisory strategy running on an automotive microprocessor. The hardware and control strategy are described together with the simulation developed to allow its calibration and validation before fitting in a B/C class European passenger car. Simulation results are presented which show the system to be controllable and responsive to deliver optimum fuel consumption, emissions and driver comfort.

The major contribution of this paper is the general description of a complete integrating procedure of autonomous vehicle system. Using Robot Operating System (ROS) as the framework, process from senor integration to path planning and path tracking were performed. Based on an off-road All-Terrain Vehicle, an Extended Kalman filter based autonomous control strategy was developed on the ROS. Both the position estimation and autonomous control were performed on the ROS platform. For the position estimation phase, sensory measurements from GPS, IMU and wheel odometry were acquired and processed on ROS. In accordance with the ROS architecture, separate packages were developed for each sensor to gather and publish corresponding measurements. Furthermore, Extended Kalman filtering was performed to fuse all sensory measurements to achieve an optimizing accuracy.

The authors describe the early stages of a programme to investigate the wear sensitivity of spool valves to abrasive contaminant in the fluid flow. Wear mechanisms in valves and aspects of test rig design are discussed. Methods of assessing wear are considered, both during and after completion of a test. Preliminary results are presented to highlight the difference between these methods and illustrate the changes in geometry that take place during the wear test.

The design of quiet power steering vane pumps requires accurate experimental and analytical tools to assess fluidborne noise. Measurement of vane pump fluidborne noise-generating potential must minimize hydraulic circuit effects. The difficulties of distinguishing between pump and hydraulic circuit effects is discussed. A technique called the “secondary source” method for measuring positive displacement pump flow ripple is described. The technique allows evaluation of the pump discharge impedance and flow ripple based on the analysis of the wave propagation characteristics in a special test circuit. This test method is used to validate a computer model of the vane pump flow ripple at the rotating group discharge. The model computes the vane chamber pressure histories which are used to obtain net discharge flow ripple. Geometric definition is kept flexible in the model so that compression and leakage can be evaluated for any vane pump design.

Developing controllers for hydraulic servos is difficult due to the inherent uncertainty and nonlinear characteristics of the system. Systems are classed as uncertain when they are subject to unknown parameter variations or disturbances, or when there is incomplete knowledge of the system model, all of which are common in hydraulic servo systems. However, unlike conventional control techniques, the use of modern control methods means that system uncertainty can be considered at the controller design stage, and consequently robust controllers can be developed. In this paper the robust control of hydraulic servo systems is considered, and sources of uncertainty typical in hydraulic drives are discussed. The effect of ignoring these uncertainties is demonstrated by simulation experiments of a hydraulic servo, comparing conventional control techniques to the modern approach of H∞ optimal control. The implementation of modern controllers is also discussed.

In traditional liquid cooled internal combustion engine systems, the coolant temperature is controlled by a thermostat which governs the coolant flow rate to the radiator. The thermostat is effectively a directional control valve in which the spool displacement is used to direct flow to the radiator. The coolant temperature is primarily a function of four parameters, namely radiator and thermostat characteristics, coolant flow rate and ambient temperature. By employing closed-loop feedback, the coolant temperature can be controlled according to environmental conditions. To achieve this goal the overall system must be correctly designed. That is the issue discussed in this paper. The increasing use of simulation for both circuit and component analysis in the automtive industry has come about due to the requirement for acceptable transient as well as steady state system performance.

Problems inherent in pressure control circuits are manifest in many common applications such as those of cushion control, and bumpless transfer between displacement and pressure control. Often, solutions involve complex electrical feedback systems to achieve the required performance characteristics. However, in many cases, a thorough understanding of the plant and control circuit should enable fulfilment of these requirements using a simple and inexpensive open-loop system. In this case the plant is an automotive CVT (Continuously Variable Transmission) which has particular performance requirements. Constraints applied by the plant characteristics dictate that large flows be catered for with a low pressure increase and also that specific frequency response features are attained.

The adoption of two stage serial turbochargers in combination with internal combustion engines can improve the overall efficiency of powertrain systems. In conjunction with the increase of engine volumetric efficiency, two stage boosting technologies are capable of improving torque and pedal response of small displacement engines. In two stage sequential systems, high pressure (HP) and low pressure (LP) turbochargers are packaged in a way that the exhaust gases access the LP turbine after exiting the HP turbine. On the induction side, fresh air is compressed sequentially by LP and HP compressors. The former is able to deliver elevated pressure ratios, but it is not able to highly compressor low flow rates of air. The latter turbo-machine can increase charge pressure at lower mass air flow and be by-passed at high rates of air flow.

Engines equipped with pressure charging systems are more prone to knock partly due the increased intake temperature. Meanwhile, turbocharged engines when operating at high engine speeds and loads cannot fully utilize the exhaust energy as the wastegate is opened to prevent overboost. The turboexpansion concept thus is conceived to reduce the intake temperature by utilizing some otherwise unexploited exhaust energy. This concept can be applied to any turbocharged engines equipped with both a compressor and a turbine-like expander on the intake loop. The turbocharging system is designed to achieve maximum utilization of the exhaust energy, from which the intake charge is over-boosted. After the intercooler, the turbine-like expander expands the over-compressed intake charge to the required plenum pressure and reduces its temperature whilst recovering some energy through the connection to the crankshaft.

When evaluating the performance of new boosting hardware, it is a challenge to isolate the heat transfer effects inherent within measured turbine and compressor efficiencies. This work documents the construction of a lumped mass turbocharger model in the MatLab Simulink environment capable of predicting turbine and compressor metal and gas outlet temperatures based on measured or simulated inlet conditions. A production turbocharger from a representative 2.2L common rail diesel engine was instrumented to enable accurate gas and wall temperature measurements to be recorded under a variety of engine operating conditions. Initially steady-state testing was undertaken across the engine speed and load range in order that empirical Reynolds-Nusselt heat transfer relationships could be derived and incorporated into the model. Steady state model predictions were validated against further experimental data.

In recent years, there has been an impetus in the automotive industry to develop newer diesel injection systems with a view to reducing fuel consumption and emissions. This development has led to hardware capable of higher pressures, typically up to 2500 bar. An increase in pressure will result in a corresponding increase in fuel temperature after compression with studies showing changes in fuel temperatures of up to 150 °C in 1000-2500 bar injection systems. Until recently, the addition of Fatty Acid Methyl Esters, FAME, to diesel had been blamed for a number of fuel system durability issues such as injector deposits and fuel filter blocking. Despite a growing acceptance within the automotive and petrochemical industries that FAME is not solely to blame for diesel instability, there is a lack of published literature in the area, with many studies still focusing on FAME oxidation to explain deposit formation and hardware durability.