Search Results

Since transient vehicle HVAC computational fluids (CFD) simulations take too long to solve in a production environment, the goal of this project is to automatically create a lumped-parameter flow network from a steady-state CFD that solves nearly instantaneously. The data mining algorithm k-means is implemented to automatically discover flow features and form the network (a reduced order model). The lumped-parameter network is implemented in the commercial thermal solver MuSES to then run as a fully transient simulation. Using this network a “localized heat transfer coefficient” is shown to be an improvement over existing techniques. Also, it was found that the use of the clustering created a new flow visualization technique. Finally, fixing clusters near equipment newly demonstrates a capability to track localized temperatures near specific objects (such as equipment in vehicles).

Test and verification procedures are a vital aspect of the development process for embedded control systems in the automotive domain. Formal requirements can be used in automated procedures to check whether simulation or experimental results adhere to design specifications and even to perform automatic test and formal verification of design models; however, developing formal requirements typically requires significant investment of time and effort for control software designers. We propose Signal Template Library (ST-Lib), a uniform modeling language to encapsulate a number of useful signal patterns in a formal requirement language with the goal of facilitating requirement formulation for automotive control applications. ST-Lib consists of basic modules known as signal templates. Informally, these specify a characteristic signal shape and provide numerical parameters to tune the shape.

Increasing fuel injection pressure has enabled reduction of diesel emissions while retaining the advantage of the high thermal efficiency of diesel engines. With production diesel injectors operating in the range from 300 to 2400 bar, there is interest in injection pressures of 3000 bar and higher for further emissions reduction and fuel efficiency improvements. Fundamental understanding of diesel spray characteristics including very early injection and non-vaporizing spray penetration is essential to improve model development and facilitate the integration of advanced injection systems with elevated injection pressure into future diesel engines. Studies were conducted in an optically accessible constant volume combustion vessel under non-vaporizing conditions. Two advanced high pressure multi-hole injectors were used with different hole diameters, number of holes, and flow rates, with only one plume of each injector being imaged to enable high frame rate imaging.

A new press/die system for restraining force control has been developed in order to facilitate an increased level of process control in sheet metal forming. The press features a built-in system for controlling drawbead penetration in real time. The die has local force transducers built into the draw radius of the lower tooling. These sensors are designed to give process information useful for the drawbead control. This paper focuses on developing models of the drawbead actuators and the die shoulder sensors. The actuator model is useful for developing optimal control methods. The sensor characterization is necessary in order to develop a relationship between the raw sensor outputs and a definitive process characteristic such as drawbead restraining force (DBRF). Closed loop control of local specific punch force is demonstrated using the die shoulder sensor and a PID controller developed off-line with the actuator model.

The Variable Dynamic Testbed Vehicle (VDTV) concept has been proposed as a tool to evaluate collision avoidance systems and to perform driving-related human factors research. The goal of this study is to analytically investigate to what extent a VDTV with adjustable front and rear anti-roll bar stiffnesses, programmable damping rates, and four-wheel-steering can emulate the lateral dynamics of a broad range of passenger vehicles. Using a selected compact-sized automobile as a baseline, our study indicated this baseline vehicle can be controlled to emulate the lateral response characteristics (including the vehicle's understeer coefficient and the 90% lateral acceleration rise time in a J-turn maneuver) of a fleet of production vehicles, from low to high lateral acceleration conditions.

The paper reviews the role of drawbeads in sheet metal stamping. The design of drawbeads is discussed in depth, with treatment of different bead cross sections, bead end shapes, and bead materials. International standards and practices are included. This is followed by the historical development of the modeling of the drawbead restraining force, starting with basic equilibrium approaches, and leading to the use of the finite element method which permits the study of drawbead effects on sheet metal flow in three dimensions. Finally, the potential of active drawbeads is described based upon ongoing research which is directed toward closed-loop computer control of the stamping process through adjustment of the drawbead penetration.

Heavy-duty diesel engine particulate matter (PM) emissions must be reduced from 0.1 to 0.01 grams per brake horsepower-hour by 2007 due to EPA regulations [1]. A catalyzed particulate filter (CPF) is used to capture PM in the exhaust stream, but as PM accumulates in the CPF, exhaust flow is restricted resulting in reduced horsepower and increased fuel consumption. PM must therefore be burned off, referred to as CPF regeneration. Unfortunately, nominal exhaust temperatures are not always high enough to cause stable self-regeneration when needed. One promising method for active CPF regeneration is to inject fuel into the exhaust stream upstream of an oxidation catalytic converter (OCC). The chemical energy released during the oxidation of the fuel in the OCC raises the exhaust temperature and allows regeneration.

The drive of Design for the Environment is to reduce the environmental impact of both design and manufacturing processes. The most frequent method recommended is to substitute better materials and processes. However, there are processes that will continue to have undesirable environmental impacts due to the lack of knowledge of better methods. These processes are critical to manufacturing of products and can not be eliminated. All possible substitutions appear to have worse impacts. This paper explores modeling these processes and imposing a control method which permits an improvement of the environmental impact.

Simultaneous control of speed and air-fuel ratio in a six-cylinder automobile engine is studied. A three-state engine model including rotational, air intake and fuel intake dynamics is used for control design. Control design focuses on application of nonlinear control techniques, specifically sliding mode control. Controllers are designed for tracking speed profiles and regulating air-fuel mixture. Multiple-surface sliding control is shown to result in good speed tracking in simulation and experiment. The production fuel controller and an observer-based sliding controller are shown to result in the best fuel control during speed transients. A standard sliding fuel controller is shown to result in high amplitude deviations due to oxygen sensor time delay. The best combination of controllers is shown to be the multiple-surface sliding speed controller and the observer-based fuel controller.

The proliferation of small silicon micro-chips has led to a large assortment of low-cost transducers for data acquisition. Production vehicles on average exploit more than 60 on board sensors, and that number is projected to increase beyond 200 per vehicle by 2020. Such a large increase in sensors is leading the fourth industrial revolution of connectivity and autonomy. One major downfall to installing many sensors is compromises in their accuracy and processing power due to cost limitations for high volume production. The same common errors in data acquisition such as sampling, quantization, and multiplexing on the CAN bus must be accounted for when utilizing an entire array of vehicle sensors. A huge advantage of onboard sensors is the ability to calculate vehicle parameters during a daily drive cycle to update ECU calibration factors in real time. One such parameter is driveline damping, which changes with gear state and drive mode. A damping value is desired for every gear state.